MX-5500N, MX-6200N, MX-7000N (serv.man33). MX-LCX3 LCT A3-Installation Manual — Sharp Copying Equipment Peripheral (repair manual)

Model
MX-5500N MX-6200N MX-7000N (serv.man33)
Pages
13
Size
3.72 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-LCX3 LCT A3-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm33.pdf
Date

View Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral online

MX-7000N  MX-LCX3  3 – 1
MX-7000N
Service Manual
 
[3] MX-LCX3
1. Unpacking
A. Pulling out of the large capacity tray (A3) unit
1)
Pull out the large capacity tray (A3) unit.
B. Removal of the fixing material and packing 
parts
1)
Remove the bundled items from the large capacity tray. 
2)
Remove the fixing material from the large capacity tray.
3)
Manually pull out the cassette.
Push the shaft at the rear side of the front cabinet to release
the lock. (About 5mm)
* When the lock is released, be careful the spring will push out
the cassette about 50mm.
4)
Slowly pull out the paper feed base tray until it stops.
5)
Remove the fixing material from large capacity tray.
MX-7000N  MX-LCX3  3 – 2
6)
Remove the fixing screws (3 pcs.) of the paper feed table of
the LCC, and remove the cautionary note A.
Note: When the power is turned on without removing the fixing
screw, remove the fixing screw and execute SIM 15.
7)
Push the large capacity tray slowly into the original position.
C. Check the packed items
1)
Check that all the items are included in the package.
2. Installation
<Note before installation>
* Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
A. Turn OFF the power of the main unit.
1)
Turn OFF the power switch on the operation panel.
A
No.
Names of bundles
Quantity
1
Mounting plate upper
2
2
Connecting plate lower front
1
3
Connecting plate lower rear
1
4
Positioning plate
2
5
Left front cabinet
1
6
Fixing screw A (S-tight, M4 x 18)
4
7
Fixing screw B (Hexagon with seat, S-tight, M4 x 12)
6
8
Fixing screw C (Binding head S tight M4x8)
1
1
2
3
4
5
8
6
7
"OFF"
"OFF"
MX-7000N  MX-LCX3  3 – 3
2)
Open the front cabinet of the main unit. Turn OFF the power
switch in the front cabinet.
3)
Disconnect the power plug of the main unit from the power out-
let.
B. Attach the mounting plate upper and the lower 
front/rear connecting plate
1)
Attach the mounting plate upper (Package part No. 1) with the
fixing screw A (Package part No. 6) to the installation part of
right side of the main unit. When installing, put the rubber sec-
tion (
) of the mounting plate upper on the lower side.
2)
Remove the fixing screws of the front/rear cover on the lower
part of the main unit. Attach the connecting plate lower front
(Package part No. 2) to the lower front side of the main unit
with the fixing screw B (Package part No. 7).
Attach the connecting plate lower rear (Package part No. 3) to
the lower rear side of the main unit with the fixing screw B
(Package part No. 7).
3)
Release the lock, and open the right door.
4)
Remove the screws, and remove the upper cover.
5)
Close the right door.
"OFF"
MX-7000N  MX-LCX3  3 – 4
6)
Remove the two fixing screws of the machine entry port, and
remove the entry port cover.
7)
Attach the entry port cover reversely to the machine and fix it
with the two fixing screws which was removed in procedure 3.
* When working, be careful to prevent damage of the paper
pass (transport) surface on the entry port cover.
8)
Release the lock, and open the right door.
9)
Install the upper cover, and fix with screws.
10) Close the right door.
C. Installation to the main unit and height 
adjustment
1)
Use the edge of the connection plates F/R mounted to the
lower side of the machine and the mark on the mounting plate
in the lower left side of the LCC to check the installation height.
Front side
Rear side
MX-7000N  MX-LCX3  3 – 5
a. When the height is properly adjusted:
When both the edges of the connecting plates on front and
rear are fit with the longest mark on the mounting plates each,
install the positioning plates (Package part No. 4) to the front
and the rear sides and fix them with the fixing screw B (Pack-
age part No. 7) (1 for each side).
Front side
Rear side
b. When the height is not properly adjusted:
Use the adjustment device on the lower left side of the LCC to
adjust the height of the left caster section.
Front side
Rear side
<1>
Loosen the hex washer based screws on the both ends of the
caster movable plate in the front and the rear sides.
F
R

Download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral

Here you can view online or download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral in pdf. This Peripheral can help you recover, restore, fix, disassemble and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).