DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ↓ Size: 5.46 MB | Pages: 20 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man72)
Pages
20
Size
5.46 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual-Main Unit
File
mx-5500n-mx-6200n-mx-7000n-sm72.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ▷ View online

MX-7000N  MX-5500N/6200N/7000N  1 – 1
MX-7000N
Service Manual
 
[1] MX-5500N/6200N/7000N
1. Installing (use) conditions
Before installing the machine, check that the following installing
(use) conditions are satisfied.
If the installing (use) conditions are not satisfied, the machine may
not display full performances, resulting in troubles. It may also
cause safety problems. Therefore, be sure to arrange the installing
(use) conditions before setting up the machine.
A. Bringing space
For installation of a large size machine, be sure to check that the
door size is great enough before bringing in.
B. Installing space
The following space must be provided around the machine in order
to assure machine performances and proper operations. If any
option is installed, provide the additional space for installing it.
Especially the space at the rear of the machine must be provided
sufficiently. If not, the machine cannot exhibit functions against
heat and dust, causing some troubles.
C. Power source (Capacity, voltage, frequency, 
safety, plug)
If the power specifications are not satisfied, the machine cannot
exhibit full performances and may cause safety trouble.
Strictly observe the following specifications.
(1) Power capacity
Check that the following power capacity is satisfied. If not, addition-
ally provide a power source.
(2) Power voltage
Measure the voltage during copying to check that the voltage is in
the range of the specified voltage 
±10%.
If the voltage is outside the specified range, use thicker lead wires
to reduce impedance. (An electrical work is required.)
Use of a step-up transformer is also available. In this case, the
capacity must be great enough for the max. Power consumption of
the machine.
(3) Power frequency, waveform
The frequency must be within the range of the specified frequency
±2%. If power waveform is deformed, a trouble may occur.
(4) Safety
Be sure to properly ground the machine.
(5) Power plug
Check the form of the power plug. If the shape does not match, do
not use it.
D. Floor strength and level
This machine is considerably heavy and becomes heavier with an
option installed. The floor must be strong enough for assuring
safety.
If the floor is not level, the toner density control is not normal, 
and the copy quality may be adversely affected.
If not, color shift or image distortion may occur.
E. Direct rays of the sun, dust, temperature, 
humidity, gasses, chemicals, vibration
(1) Temperature and humidity
This machine is designed to perform properly under the specified
temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Do not install the machine near a heater, a cooler, or a humidifier.
Dew may be formed inside the machine to cause a trouble. Use
enough care for ventilation.
• Working environment
Temperature: 10 to 35
°C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
No
Content
1
Bringing space
2
Installing space
3
Power source (Capacity, voltage, frequency, safety)
4
Floor strength
5
Direct rays of the sun, dust, temperature, humidity, gasses, 
chemicals
Power capacity
Japan
20A or more
EX 100V
15A or more
EX 200V
10A or more
30cm
30cm
45cm
85%
(humidity)
(Temperature)
60%
20%
MX-7000N  MX-5500N/6200N/7000N  1 – 2
(2) Dust
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
(3) Direct rays of the sun
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
(4) Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, Be sure to use the skid slope (DKIT-
0367FCZZ). Be careful to safety and pull the machine down. The
carrying in must ensure manpower of four persons or more for
safety. The machine is considerably heavy, and requires safety
precautions for delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
3. Unpacking
A. Pulling out of the main unit
1)
Remove the top case, the top cushion, the packing case, and
the bundled item.
No
Content
Method
1
Implements, facility, and 
manpower
Use a forklift. (If no forklift is 
available, ensure manpower of four 
persons or more, and use the skid 
slope (DKIT-0367FCZZ)).
2
Delivery
Transit must be made in packed 
condition.
MX-7000N  MX-5500N/6200N/7000N  1 – 3
2)
Cut the four corners of the bottom case.
3)
Lift the main unit slightly, and remove the bottom pad R.
4)
Lift the main unit slightly, and remove the bottom pad L.
5)
Remove the vinyl bag from the main unit.
6)
Remove the slope.
* Slope : Deal as a parts.
7)
Attach the slope to the concave section of the skid.
Part name
Part code
Skid slope
DKiT– 0367FCZZ
MX-7000N  MX-5500N/6200N/7000N  1 – 4
8)
Hold the grips of main unit and pull them down in the arrow
direction.
B. Removal of the fixing tape and protection 
material
1)
Remove the fixing tape and protection material.
C. Pulling out of the bundled items
1)
Pull out the bundled items.
D. Check the packed items
1)
Check that all the items are included in the package.
NO.
Names of bundles
Quantity
1
Waste toner bottle
1
2
Paper exit tray
1
3
Paper exit full detection actuator
1
4
Operation manual pocket
1
5
Operation manual
1
1
2
3
4
5
Page of 20
Display

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ▷ Download

  • DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ↓ Size: 5.46 MB | Pages: 20 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.