MX-5500N, MX-6200N, MX-7000N (serv.man29). MX-FNX4 4K Saddle Stitch Finisher-Installation Manual — Sharp Copying Equipment Peripheral (repair manual)

Model
MX-5500N MX-6200N MX-7000N (serv.man29)
Pages
9
Size
3.08 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-FNX4 4K Saddle Stitch Finisher-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm29.pdf
Date

View Sharp MX-5500N / MX-6200N / MX-7000N (serv.man29) Peripheral online

MX-7000N  MX-FNX4  8 – 1
MX-7000N
Service Manual
 
[8] MX-FNX4
1. Unpacking
A. Removal of the saddle stitch finisher
* For removal of the saddle stitch finisher, manpower of two per-
sons or more is required.
1)
Remove the fixing material, and remove the top case.
2)
Remove the bundled items from packing cushion.
3)
Holding the upper part of the saddle stitch finisher by two peo-
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot. )
4)
Remove the skid and packing cushions.
5)
One person tilt the saddle stitch finisher, another person
remove the lower tray.
6)
Remove the other side similarly.
MX-7000N  MX-FNX4  8 – 2
B. Removal of the protection material
1)
Remove the fixing tapes and protection material.
2)
Remove the screws and remove the fixing material for paper
exit tray. (four positions)
3)
Open the front door of the finisher, and remove the fixing tapes
and protection material.
4)
Pull out the stapler unit.
5)
Remove the screw, and remove the fixing material of the sta-
pler unit.
MX-7000N  MX-FNX4  8 – 3
6)
Replace the stapler unit to the original position, and close the
front door.
7)
Remove the fixing screws, and remove the right lower cover.
8)
Remove the fixing screws, and remove the pressure release
plates of saddle section.
9)
Attach the right lower cover with the fixing screws.
C. Check the packed items
1)
Check that all the items are included in the package.
No.
Names of bundles
Quantity
1
Binding head round tapping M4x8
2
2
IT tapping M4x20
2
3
Binding head M4x12
4
4
Step screw B
2
5
Rail
1
6
Rail reception sheet metal
1
7
Connection fixture F (for x4)
1
8
Connection fixture R (for x4)
1
9
Staple position label (For scanner)
1
10
Staple position label (For DSPF)
1
11
Punch position label (For scanner)
1
12
Punch position label (For DSPF)
1
1
8
9
2
3
4
5
6
7
10
X4
X4
12
11
MX-7000N  MX-FNX4  8 – 4
2. Installation
<Note before installation>
* When the MX-FNX4 is installed, first install the MX-RBX2, and
then install the MX-FNX4.
* When the MX-FNX4 and MX-PNX2 is installed at the same time,
first install the MX-PNX2, and then install the MX-FNX4.
* When the MX-FNX4 and MX-CFX1 is installed at the same time,
execute the installation procedure of MX-CFX1.
A. Installation of the rail
1)
Install the rail (Package part No. 5) to the saddle stitch finisher
with the fixing screws (Package part No. 1).
2)
Install the rail reception sheet metal (Package part No. 6) to
the main unit with the fixing screws (Package part No. 3).
B. Installation of the connection fixture F/R
1)
Install the connection fixture R (Package part No. 8) to the
main unit with the fixing screws (Package part No. 3).
2)
Install the connection fixture F (Package part No. 7) to the
main unit with the fixing screws (Package part No. 3).
C. Check of the connected position of main unit 
and finisher
1)
Insert the rail of the finisher into the slit on the rail reception
sheet metal of the main unit, install the finisher.
2)
Remove the screw, and remove the connector cover on rear
side of the finisher.
MX-7000N  MX-FNX4  8 – 5
3)
Check that the center of the screw hole of the finisher is in the
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
* When not the range of specification, execute the following
adjustment. If the adjustment is not required, Progress to the
procedure of "E. Touch of the auxiliary caster with the floor".
D. Adjustment
1)
Remove the finisher from the main unit.
2)
Open the front door.
3)
Remove the cabinet fixing screw.
4)
Remove the screw, and remove the front lower cabinet 1.
Remove the fixing screw of the front lower cabinet 2.
5)
Remove the screws, and slide to the left the front lower cabinet
2, and remove it.
6)
Remove the fixing tapes.

Download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man29) Peripheral

Here you can view online or download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man29) Peripheral in pdf. This Peripheral can help you recover, restore, fix, disassemble and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man29) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man29) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).