DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Service Manual ↓ Size: 2.19 MB | Pages: 12 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man26)
Pages
12
Size
2.19 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX PEX2 INSTALLATION MANUAL
File
mx-5500n-mx-6200n-mx-7000n-sm26.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Peripheral ▷ View online

INSTALLATION MANUAL
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
CHAPTER 1. Configuration
CHAPTER 2. Installation in MX-3500/4500 series
CHAPTER 3. Installation in MX-5500N/6200N/7000N
CONTENTS
CODE: 00ZMXPEX2/I1E
DIGITAL FULL COLOR 
MULTIFUNCTIONAL SYSTEM OPTION
PRINT CONTROLLER UNIT
MODEL
MX-PEX1
MX-PEX2
MX-PEX2  Configuration  1 – 1
MX-PEX2
Service Manual
 
[1] Configuration
1. Combination list
2. Unpacking
1)
Remove the print controller unit.
3. Packed items
1)
Check that all the items are included in the package.
4. NOTE FOR INSTALLATION
The MFP model is detected when the power is turned on for the first time after the shipment from the factory, and the system that matches the
MFP (MX-5500N/6200N/7000N or MX-3500/4500 series) is started.
After the system is started, the initial setup screen is displayed.
After the completion of the setup, the detection of MFP model at the boot-up will not be executed.
It is necessary to return the controller to the default state if you want to re-connect it to another MFP after the setup.
System setting 
→ Printer Setting (administrator area) → Fiery Setting → Run Setup
Password: Fiery.1 (Default) 
→ Factory Default
NOTE: Please make sure to reset to the default state if you connect the controller to another model, because the controller starts
even when it is connected to another MFP (e.g., the controller set for MX-3500/4500 series to the MFP for MX-5500N/6200N/
7000N) even after completion of the setup. 
NOTE: MX-PEX1 was shipped after setting the basic setting (the information of MFP) by default, but MX-PEX2 is shipped in the fac-
tory shipment setting (without setting of the information of MFP), because it is necessary to detect MFP when turning on the
power.
MX-PEX1
MX-PEX2
MX-3500/4500 series
YES
YES
MX-5500N/6200N/7000N
NO
YES
No.
Names of bundles
Quantity
1
I/F unit
1
2
Step screw
2
3
LAN cable (cross cable)
1
4
AC power cable
1
5
Caution label
1
6
CD-ROM
7
7
Quick guide
1
8
Release notes
1
9
KODAK chart
1
1
4
2
3
6
7
8
5
9
CAUTION:MX-PEX2 is compatible with both MX-5500N/6200N/7000N and MX-3500/4500 series.
MX-PEX2  Installation in MX-3500/4500 series  2 – 1
MX-PEX2
Service Manual
 
[2] Installation in MX-3500/4500 
series
<Note before installation>
* Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
1. Turn off the power of the main unit
1)
Turn the power switch located on the operation panel to the
"OFF" position.
2)
After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the “OFF” opsi-
tion.
3)
Remove the power plug of the main unit from the outlet.
2. Install of the I/F unit
1)
Remove the ozone filter cover. Remove the screws, and
remove the right rear cabinet cover.
2)
Remove the screws, and pull out the MFP cnt PWB unit.
3)
Remove the three screws of the MFP cnt PWB. Install the I/F
unit (package part No. 1) with the three screws that was
detached from MFP cnt PWB.
* When installing the I/F unit, use an extreme care to make
the sheet metal not come in contact with the MFP cnt PWB.
OFF
OFF
OFF
3
2
1
1
2
3
MX-PEX2  Installation in MX-3500/4500 series  2 – 2
4)
Restore the MFP cnt PWB unit to the main unit, and fix with the
screws.
5)
Cut out the cut-out portion of the right rear cabinet cover for
cable along the perforated line. Attach the right rear cabinet
cover, and fix with the screw. Attach the ozone filter cover.
3. Installation of the printer controller
1)
Remove the four screws from the rear cabinet. Attach two step
screws (package part No. 2) to the two positions in four posi-
tions where the fixing screws have been removed.
2)
Engage the printer controller unit with the step screws, and
slide it to the right door side.
3)
Fix the print controller unit using the two screws of the four
screws removed in step 1.
4. Connector connection
1)
Connect the cable (A) of the I/F unit, the LAN cable (package
part No. 3), and the AC power cord (C) (package part No. 4).
4
3
2
1
1
1
1
1
2
1
2
A
B
C
Page of 12
Display

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Peripheral ▷ Download

  • DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Service Manual ↓ Size: 2.19 MB | Pages: 12 in PDF or view online for FREE
  • Here you can View online or download the Peripheral for the Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Peripheral (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.