DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Service Manual ↓ Size: 2.09 MB | Pages: 6 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man30)
Pages
6
Size
2.09 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-PNX2A-D Punch Module-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm30.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Peripheral ▷ View online

MX-7000N  MX-PNX2A/B/C/D  6 – 1
MX-7000N
Service Manual
 
[6] MX-PNX2A/B/C/D
1. Unpacking
A. Pulling out of the punch unit
1)
Pull out the punch unit.
B. Removal of the protection material
1)
Remove the fixing tape and protection material.
2)
Open the front cover, and open the top cover.
3)
Remove the screws, and remove the fixing material. (2 posi-
tions)
4)
Close the top cover, and close the front cover.
1
2
1
2
MX-7000N  MX-PNX2A/B/C/D  6 – 2
C. Check the packed items
1)
Check that all the items are included in the package.
2. Installation
<Note before installation>
* Before installing the MX-PNX2, unpack the MX-FNX3 or MX-
FNX4.
A. Installation of punch unit
* Carry out the procedure 1) only for MX-FNX4.
1)
Peel off the released paper of the washer (Package part No.
9), and stick it to the finisher.
2)
Attach the step screw A (Package part No. 2) to the finisher.
3)
Remove the fixing screw, and remove the connector cover on
rear side of the finisher.
4)
Hang the punch unit on the step screws installed to the fin-
isher.
5)
Tighten the step screws bundled to the punch unit, fix the
punch unit.
No.
Names of bundles
Quantity
1
P tight M4x12
1
2
Step screw A
2
3
Cap screw M3x6
3
4
Binding head M4x12
4
5
Front cover
1
6
Front cover mounting fixture
1
7
Connection fixture F (for punch)
1
8
Connection fixture R (for punch)
1
9
Washer (For MX-FNX4 only)
1
1
2
3
5
6
7
8
9
MX-FNX4
only
P
P
4
1
2
MX-7000N  MX-PNX2A/B/C/D  6 – 3
6)
Attach the front cover mounting fixture (Package part No. 6)
with the fixing screws (Package part No. 3).
• In the case of the saddle stitch finisher (MX-FNX4)
Install it using three fixing screws (Package part No. 3) bun-
dled to punch unit.
• In the case of the finisher (MX-FNX3)
Remove the screw of the finisher, and reuse it. Install it using
the reuse screw, and three fixing screws (Package part No.
3) bundled to punch unit.
7)
Open the front door of punch unit.
8)
Engage the pawls of the rear side of front cover (Package part
No. 5), attach the front cover with the fixing screw (Package
part No. 1).
B. Connection of connector of the finisher and 
punch unit
1)
Remove the fixing screws, and remove the rear cover.
2)
Connect two connectors of the finisher to the PWB of punch
unit, and fix the harness to the clamp.
* When installing the MX-CFX1, execute the installation procedure
of MX-CFX1. If not, execute the following procedures.
C. Install of the Connection fixture F/R
1)
Install the Connection fixture F (Package part No. 7) to the
main unit with the fixing screws (Package part No. 4).
1
2
3
MX-7000N  MX-PNX2A/B/C/D  6 – 4
2)
Install the Connection fixture R (Package part No. 8) to the
main unit with the fixing screws (Package part No. 4).
D. Check of the connected position of main unit 
and finisher
1)
Engage the finisher that has installed punch unit to the main
unit, and temporarily fix.
* Insert the rail of the finisher unit into the rail reception fixture
of main unit, fix temporarily.
2)
Open the front door of punch unit.
3)
Check that the center of the screw hole of the punch unit is in
the range of specification of an oval hole of the mounting fix-
ture  in front side of main unit.
* When not the range of specification, execute the adjustment
procedure of each finisher. If the adjustment is not required,
execute the procedure for touch of the auxiliary caster with
the floor of each finisher.
E. Adjustment
* Refer to the adjustment procedure of each finisher.
F. Touch of the auxiliary caster with the floor.
* Refer to the procedure for touch of the auxiliary caster with the
floor of each finisher.
G. Install to main unit
1)
Engage the finisher that has installed punch unit to the main
unit.
2)
Open the front door of punch unit.
Page of 6
Display

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Peripheral ▷ Download

  • DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Service Manual ↓ Size: 2.09 MB | Pages: 6 in PDF or view online for FREE
  • Here you can View online or download the Peripheral for the Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Peripheral (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.