MX-5500N, MX-6200N, MX-7000N (serv.man27). MX-RBX2 Paper Pass Unit-Installation Manual — Sharp Copying Equipment Peripheral (repair manual)

Model
MX-5500N MX-6200N MX-7000N (serv.man27)
Pages
5 Few pages! See other manuals at the bottom of the first or last page.
Size
2.18 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-RBX2 Paper Pass Unit-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm27.pdf
Date

View Sharp MX-5500N / MX-6200N / MX-7000N (serv.man27) Peripheral online

MX-7000N  MX-RBX2  4 – 1
MX-7000N
Service Manual
 
[4] MX-RBX2
1. Unpacking
A. Pulling out of the paper pass unit
1)
Pull out the paper pass unit.
B. Removal of the protection material
1)
Remove the fixing tape.
C. Check the packed items
1)
Check that all the items are included in the package.
* Use the short harness (Package part No. 7) only for North Amer-
ica and Australia,  New Zealand. It is not used in other destina-
tions.
No.
Names of bundles
Quantity
1
Binding head round tapping M4x7
11
2
Binding head P tight M4x10
6
3
hand screw
1
4
E-ring
1
5
Right rail mounting fixture
1
6
Reverse detection lever
1
7
Short harness *
1
8
Left cabinet upper
1
9
Left cabinet lower
1
10
Right rail
1
11
Left rail
1
12
Upper front cover 
1
13
Reverse tray
1
1
2
3
5
8
9
10
11
12
13
6
4
7
MX-7000N  MX-RBX2  4 – 2
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn OFF the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet of the main unit. Turn OFF the power
switch in the front cabinet.
3)
Disconnect the power plug of the main unit from the power out-
let.
B. Removal of the toner cartridge
1)
Open the toner cover.
2)
Remove the toner cartridge.
C. Removal of the paper exit tray
1)
Remove the E-ring, and remove the toner cover.
2)
Remove the paper holding arm and the paper exit full detec-
tion actuator.
3)
Remove the screws, and remove the paper exit tray.
"OFF"
"OFF"
"OFF"
MX-7000N  MX-RBX2  4 – 3
D. Installation of the short-circuit harness
* As for the following procedures, only destinations other than
North America, Australia, and New Zealand are required. For
North America and Australia, New Zealand, progress to the pro-
cedure of "E. Installation of the reverse detection lever".
1)
Remove the screw, and remove the switch cover.
2)
Install the short harness (Package part No. 7).
3)
Install the switch cover, and fix it with the screw.
E. Installation of the reverse detection lever
1)
Install the reverse detection lever (Package part No. 6).
* Be careful of the installing direction of the reverse detection
lever.
F. Installation of the right rail
1)
Fix the right rail mounting fixture (Package part No. 5) to the
main unit with the fixing screws (Package part No. 1).
2)
Engage the right rail (Package part No.10) to cut-out portion of
main frame. (Refer to (A) and (B).)
Install the right rail while pressing so that engage the projec-
tion of the main unit frame with the hole (C) in rear side of the
right rail.
* When installing, check that the reverse detection lever (D) is
in the cut-out portion in the sheet metal of the right rail.
A
B
C
D
MX-7000N  MX-RBX2  4 – 4
3)
Fix the right rail with the fixing screw (Package part No. 1).
G. Installation of the left rail
1)
Insert the rib of the left rail (Package part No. 11) into the slit
on the lower surface of the scanner left cabinet. Fix the left rail
with the fixing screws (Package part No. 1).
H. Installation of the reverse tray
1)
Insert the reverse tray (Package part No. 13) according to the
guide of the right rail and the left rail.
2)
Fix the reverse tray with the hand screw (Package part No. 3)
while holding it to upper direction.
I. Installation of the paper pass unit
1)
Pull out the slide rails.
2)
Place the paper pass unit on the slide rails, and fix it with the
fixing screws (Package part No. 1).
* Fix the screws from the rear side sequentially.
3)
Push the paper pass unit into the main unit to install.
1
2
3
4
MX-7000N  MX-RBX2  4 – 5
4)
Insert the upper front cover (Package part No. 12) to the sup-
porting point, and fix it with a E-ring (Package part No. 4).
5)
Fix the wire with fixing screws (Package part No. 2).
J. Installation of the left cabinet upper and lower
* If the MX-CFX1 is installed, The following procedures are unnec-
essary.
1)
Attach the left cabinet upper (Package part No. 8) and the left
cabinet lower (Package part No. 9) to the main unit with the fix-
ing screws (Package part No. 2).
K. Installation of the toner cartridges
1)
Install the toner cartridges.
2)
Close the upper front cover.
1
2

Download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man27) Peripheral

Here you can view online or download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man27) Peripheral in pdf. This Peripheral can help you recover, restore, fix, disassemble and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man27) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man27) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).