Sharp UP-3500 (serv.man25) Service Manual ▷ View online
Page 37 - 39
75.
Enhance of Free Text programming.
In order to enhance the Free Text programming, the following specification are implemented.
Whenever the Free Text has been changed and saved:
Whenever the Free Text has been changed and saved:
• It will be taken over in the Free Text list to make the selection more easily.
• It will also be stored as the text for the related function key. The new text will
automatically be shown on the Free Text key on the screen.
76.
Registration of scale item with tara result in error.
By some scale models, the calculation of the item amount takes more time in case of working
with the tara function. Because the ECR is awaiting the item amount right after sending the item
details to the scale, an error will occure because the scale is not ready for sending the
calculated data. To avoid this, with this version a new parameter has been introduced, for
setting a waiting between sending the data to the scale and requesting the calculated data from
the scale. The waiting time can be set from 1 to 9 which correspond to 100ms to 900ms. A
value of 0 disable the timer.
with the tara function. Because the ECR is awaiting the item amount right after sending the item
details to the scale, an error will occure because the scale is not ready for sending the
calculated data. To avoid this, with this version a new parameter has been introduced, for
setting a waiting between sending the data to the scale and requesting the calculated data from
the scale. The waiting time can be set from 1 to 9 which correspond to 100ms to 900ms. A
value of 0 disable the timer.
PGM2 MODE\SETTING\TERMINAL\SCALE WAIT
77.
Inline System with Backup Master.
If presets for centralized data, in example for Clerks or Employees, has been changed after
setup the IRC system, the data base of the Master has to be synchronized with the Backup
Master again. For the synchronisation carry out the job:
setup the IRC system, the data base of the Master has to be synchronized with the Backup
Master again. For the synchronisation carry out the job:
\PGM2\SETTING\9 DECLARE AND RECOVERY MA/BMA\2 SYNCHRONIZE DB MA/BMA
The above mentioned job has also to be carried out, if SRV #987A (TimeIn compulsory) has
been changed after setup the system.
been changed after setup the system.
78.
TimeOut by Terminal-CCD with Employee Transaction file.
To avoid Online communication problems due to a not carried out CCD Report, the last
Employee have to make the CCD prior to his TimeOut operation. This specification was valid
since V1.22. By this version, a new SRV parameter, #986A +2, is available. If this parameter is
set, the last Employee is able to make his TimeOut operation, even the CCD has not been
done.
Employee have to make the CCD prior to his TimeOut operation. This specification was valid
since V1.22. By this version, a new SRV parameter, #986A +2, is available. If this parameter is
set, the last Employee is able to make his TimeOut operation, even the CCD has not been
done.
79.
Orderman registration of SIDEABLE PLUs.
A SIDEABLE PLU registration done at the OM Handheld was not allowed. This specification
has been changed. Now, SIDEABLE as well as SIDE PLU registration becomes available.
Since the OM has no entry sequence checking, the Clerk has to take care that a SIDEABLE
PLU must be registered prior to any SIDE or SIDE W. ROLLUP –PLU. Furthermore it is not
allowed to enter any other quantity than 1 for any SIDEABLE PLU registration. Any void or
additional registration by the OM, to an already registered SIDEABLE PLU, is also not allowed
and will result in an error.
has been changed. Now, SIDEABLE as well as SIDE PLU registration becomes available.
Since the OM has no entry sequence checking, the Clerk has to take care that a SIDEABLE
PLU must be registered prior to any SIDE or SIDE W. ROLLUP –PLU. Furthermore it is not
allowed to enter any other quantity than 1 for any SIDEABLE PLU registration. Any void or
additional registration by the OM, to an already registered SIDEABLE PLU, is also not allowed
and will result in an error.
Page 38 - 39
80.
Corrected phenomenons.
• Header print of the copy for Advance Order and Credit Customer Advance Order.
In case of print out a copy of a previous made Advance Order or Credit Customer Advance
Order registration, the text COPY was printed on the wrong position in the header. This problem
happened only, if the TM-T88 is assigned as a receipt printer.
Order registration, the text COPY was printed on the wrong position in the header. This problem
happened only, if the TM-T88 is assigned as a receipt printer.
• The following bugs in relation to an Orderman registration have been solved.
- A Bill Separation of a Condiment has been printed on the KP as a void.
- A Bill Separation of a Combo PLU has been printed on the KP as a void.
- A Bill Separation of a Drink Dispenser article has been send as a void to the Drink
- A Bill Separation of a Condiment has been printed on the KP as a void.
- A Bill Separation of a Combo PLU has been printed on the KP as a void.
- A Bill Separation of a Drink Dispenser article has been send as a void to the Drink
Dispenser.
- A Bill Separation of a Link PLU could result in a system hang up at the ECR.
- Now, all Bill Separations from the Orderman will be marked with BS at the ECR’s E/J or
- Now, all Bill Separations from the Orderman will be marked with BS at the ECR’s E/J or
journal print and is no longer treated as a void.
• Direct and Indirect Void of Drink Dispenser article.
In “\PGM2 MODE\2 SETTING\10 OPTIONAL\1 FUNCTION PROHIBITED” it is possible to set
‘ISSUE ITEM VOID’ and ‘NO ISSUED VOID’ to limited access. If one of these void functions
has been carried out for a Drink Dispenser article, the ECR pops up with an error message
correctly, but the voided article was sent to the Drink Dispenser by mistake in case of using the
Credit-Mode.
‘ISSUE ITEM VOID’ and ‘NO ISSUED VOID’ to limited access. If one of these void functions
has been carried out for a Drink Dispenser article, the ECR pops up with an error message
correctly, but the voided article was sent to the Drink Dispenser by mistake in case of using the
Credit-Mode.
• VAT information on BILL in case of VIP sales.
In case of VIP sales, the article prices will become 0 prices. No VAT information is printed on
the receipt. But on a bill there will be a print out of the VAT information. With this new version,
there is also no print out of the VAT information on the bill.
the receipt. But on a bill there will be a print out of the VAT information. With this new version,
there is also no print out of the VAT information on the bill.
• Wrong range setting for GLU- and ROOM- Reading.
For the reports GLU (#32) and ROOM GLU (#34) at “\2 X1/Z1 MODE\READING\”, wrong
numbers for the given range were displayed. This has been corrected.
numbers for the given range were displayed. This has been corrected.
• Misprint at PGM reading.
In the PGM reading print out for “\PGM2 MODE\1 READING\26 OPTIONAL” there was a
misprint of set parameters at ‘FUNCTION SELECT2’.
misprint of set parameters at ‘FUNCTION SELECT2’.
• VAT shift calculation for an article with given discount.
A VAT shift calculation for an article with a discount could cause in a Break Error.
• Item registration becomes Condiment item.
After the registration of a Condiment out of a PLU Menu screen, the next registration, of the
same last Condiment item in the same PLU Menu screen, was added to the Condiment
registration. With this version, the next registered same article is treated like an individual item
registration.
same last Condiment item in the same PLU Menu screen, was added to the Condiment
registration. With this version, the next registered same article is treated like an individual item
registration.
• Employee TimeOut after Terminal CCD.
In an Inline-System, the last signed on employee could not make his TimeOut after he has
made the Terminal CCD. The error message “CCD ENTRY ERROR” appeared. After the
System-General-Z-Report has been taken, the employee could make the TimeOut. With this
ROM-Version, the last employee can make a TimeOut after he made the Terminal CCD.
made the Terminal CCD. The error message “CCD ENTRY ERROR” appeared. After the
System-General-Z-Report has been taken, the employee could make the TimeOut. With this
ROM-Version, the last employee can make a TimeOut after he made the Terminal CCD.
• Screen get garbled.
In case of the drawer alarm is set and the drawer will be opened manually while the screen
saver is active, the screen content gets garbled.
saver is active, the screen content gets garbled.
Page 39 - 39
81.
New/Changed Parameter.
SRV
• #901A +4 VAT ratio for PLU
• #908C +1 Reset Transaction number after Closed Transaction Z Report also
• #929A Solid line printing for KP, Receipt and KP
• #981D +1 PLU-Search algorithm
• #987C +2 Supervisor can work on his own account
• #987B +2 Employee password in case of Employee –Sales and –Consumption
• #988C Number of copies of the CCD report in case of Terminal-CCD
• #921C +4 VAT Shift toggle
• #981B +1 Clear Data Entries by Open Receipt
• #986C +4 Detailed General Report data print on Journal and in E/J
• #987D +2 ST(%), ST(-) and GrpDisc(%) discounts
PGM
• \PGM2 MODE\2 SETTING\10 OPTIONAL\6 DISPLAY SELECT\PLU MENU AFT. COND
Screen return logic after Condiment from a PLU Menu screen
• \PGM2 MODE \2 SETTING\1 ARTICLE\6 PLU MENU KEY\[PLU MENU]\KEY STYLE
PRESET\PLU MENU COLOUR
Key colour for PLU Menu articles
Key colour for PLU Menu articles
• \PGM2 MODE\2 SETTING\10 OPTIONAL\6 DISPLAY SELECT\HOME SCREEN #
Define a screen as new HOME screen
• \PGM2 MODE\2 SETTING\18 ORDER MASK\3 MASK ATTRIBUTE
Mask colour setting
• PGM2 MODE\SETTING\MESSAGE\MESSAGE OPTIONS\ Scroll message timer
• PGM2 MODE\SETTING\OPTIONAL\FUNCTION SELECT2\GDSC DEPT LOOKUP
• PGM2 MODE\SETTING\OPTIONAL\FUNCTION SELECT2\CLEAR GLU# DISP
• PGM2 MODE\SETTING\OPTIONAL\FUNCTION SELECT2\LEAVE XZ AFTER CCD
• PGM2 MODE\SETTING\TERMINAL\SCALE WAIT
Page 39 - 39
81.
New/Changed Parameter.
SRV
• #901A +4 VAT ratio for PLU
• #908C +1 Reset Transaction number after Closed Transaction Z Report also
• #929A Solid line printing for KP, Receipt and KP
• #981D +1 PLU-Search algorithm
• #987C +2 Supervisor can work on his own account
• #987B +2 Employee password in case of Employee –Sales and –Consumption
• #988C Number of copies of the CCD report in case of Terminal-CCD
• #921C +4 VAT Shift toggle
• #981B +1 Clear Data Entries by Open Receipt
• #986C +4 Detailed General Report data print on Journal and in E/J
• #987D +2 ST(%), ST(-) and GrpDisc(%) discounts
PGM
• \PGM2 MODE\2 SETTING\10 OPTIONAL\6 DISPLAY SELECT\PLU MENU AFT. COND
Screen return logic after Condiment from a PLU Menu screen
• \PGM2 MODE \2 SETTING\1 ARTICLE\6 PLU MENU KEY\[PLU MENU]\KEY STYLE
PRESET\PLU MENU COLOUR
Key colour for PLU Menu articles
Key colour for PLU Menu articles
• \PGM2 MODE\2 SETTING\10 OPTIONAL\6 DISPLAY SELECT\HOME SCREEN #
Define a screen as new HOME screen
• \PGM2 MODE\2 SETTING\18 ORDER MASK\3 MASK ATTRIBUTE
Mask colour setting
• PGM2 MODE\SETTING\MESSAGE\MESSAGE OPTIONS\ Scroll message timer
• PGM2 MODE\SETTING\OPTIONAL\FUNCTION SELECT2\GDSC DEPT LOOKUP
• PGM2 MODE\SETTING\OPTIONAL\FUNCTION SELECT2\CLEAR GLU# DISP
• PGM2 MODE\SETTING\OPTIONAL\FUNCTION SELECT2\LEAVE XZ AFTER CCD
• PGM2 MODE\SETTING\TERMINAL\SCALE WAIT
