DOWNLOAD Sharp MX-6500N / MX-7500N (serv.man20) Service Manual ↓ Size: 1.13 MB | Pages: 127 in PDF or view online for FREE

Model
MX-6500N MX-7500N (serv.man20)
Pages
127
Size
1.13 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Section 6 Simulation
File
mx-6500n-mx-7500n-sm20.pdf
Date

Sharp MX-6500N / MX-7500N (serv.man20) Service Manual ▷ View online

MX-7500N  SIMULATION  6 – 1
MX-7500N
Service Manual
 
[6] SIMULATION
1. General and purpose
The  simulation  mode  has  the  following  functions,  to  display  the
machine operating status, identify the trouble position and causes
in an earlier stage, and to efficiently setup and adjust the machine
for improved serviceability.
1) Various adjustments
2) Setting of the specifications and functions
3) Canceling troubles
4) Operation check
5) Counters check, setting, clear
6) Machine  operating  conditions  (operation  hysteresis),  data
check, clear.
7) Various  (adjustments,  setting,  operation,  counters,  etc.)  data
transport.
2. Starting the simulation
Entering the simulation mode
1) Double-click  the  [HOME]  key.  (Total  use  quantity/Toner
remaining quantity display mode screen)
2) Touch  the  VER  display  section.  (10-key  mode  input  mode
screen)
3) Touch the (#) key - Asterisk (*) key - Clear key - 
Asterisk (*) key - Ready for input of main code of simulation.
4) Enter  a  main  SIM  code  with  the  10-key  pad  then  touch  the
[START] key or select a main code from the SIM key list on the
touch panel.
5) Enter a sub code with the 10-key pad, then touch the [START]
key or select a sub code from the code list on the touch panel.
6) Select an item with the scroll key and the item key.
7) The machine enters the mode corresponding to the selected
item. Press [START] key or [EXECUTE] key to start the simu-
lation operation.
To cancel the current simulation mode and change the main
code and the sub code, press [BACK] key.
Canceling the simulation mode to return to the normal mode
1) Press [EXIT] key.
NOTE: Do not turn OFF the power when the machine is in the sim-
ulation mode.
If the power switch should be turned OFF in the simulation
mode,  a  malfunction  may  be  resulted.  In  this  case,  turn
OFF/ON the main power source.
Touch the [BACK] key.
[BACK] key
VER display section
(10-key mode input mode screen)
Touch the VER display section.
MX-7500N  SIMULATION  6 – 2
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
NO
YES
YES
NO
NO
YES
YES
NO
Standby for entry of SIM
sub code
Enter SIM sub code with
the 10-key.
Press the 
COLOR/MONO key.
The display is made according
to the selected mode and the item.
START (Copy mode)
Double-click the HOME key.
Touch the VER display section.
Press the sharp (#) key.
Press the asterisk (*) key.
Press the clear key.
Press the Program key.
Standby for entry of
SIM code.
Enter the main code of
SIM with the 10-key.
The main code of SIM
is displayed.
Press the 
COLOR/MONO key.
Is there a sub code ?
Select the mode and the
item with the scroll key 
and the item key.
Operation check ?
Operating conditions
check ?
Data clear ?
Adjustments
or setting (counter data
change) ?
Do you
want to change the
content ?
Enter the new setting and
adjustment values.
Press the BACK key
Press the BACK key
Press the EXECUTE key
and OK key.
Operation is made according
to the selected mode and item.
Press the EXECUTE key
and OK key.
Press the EXECUTE key
and OK key.
The display is made according to
the selected some and the item.
Press the EXECUTE key
and OK key.
Is it the same
simulation main
code?
Do you want
to perform another
simulation ?
Do you
want to end the
simulation ?
The changed content
is stored.
The simulation mode
is canceled.
Press the EXIT key.
Operation is made according
to the selected mode and the item.
(Other modes)
The selected mode and
the item are cleared.
        <Exclusion type>
You have to exit
simulation mode
before entering into
this mode for self
printing type.
In the power OFF/ON type
 simulation, OFF/ON
 message is
 displayed by the
 SYSTEM
 SETTINGS key.
If there is no item.
MX-7500N  SIMULATION  6 – 3
3. List of simulation codes
Main
Sub
Functions
Section
1
1
Used to check the operation of the scanner (reading) unit and the control circuit.
Scanner (reading)
2
Used to check the sensors in the scanner (reading) section and the related circuits.
Scanner (reading)
5
Used to check the operation of the scanner (reading) unit and the control circuit.
Scanner (reading)
2
1
Used to check the operations of the automatic document feeder and the control circuit.
DSPF
2
Used to check the operations of the sensors and the detectors in the automatic document feeder section 
and the control circuits.
DSPF
3
Used to check the operations of the loads in the automatic document feeder and the control circuit.
DSPF
6
Used to check the operation of the scanner fan motor.
Scanner (reading)
3
2
Used to check the operations of the sensors and the detectors in the finisher and the control circuit.
Finisher
3
Used to check the operation of the load in the finisher and the control circuit.
Finisher
10
Used to adjust the finisher.
Finisher
30
Inserter sensor check
Inserter
31
Inserter individual load check
Inserter
40
Paper folding unit sensor check
Paper folding unit
41
Paper fold unit individual load check
Paper folding unit
42
Paper folding unit adjustment
Paper folding unit
50
Decurler sensor check
Decurler
51
Decurler individual load check
Decurler unit
60
Stacker sensor check
Stacker unit
61
Stacker individual load check
Stacker unit
62
Stacker adjustment
Stacker unit
70
Booklet maker sensor check
Booklet maker
4
2
Used to check the operations of the sensors and detectors in the desk/large capacity tray (LCC), and the 
control circuit of those.
Desk/Large capacity tray (LCC)
3
Used to check the operations of the loads in the desk/large capacity tray (LCC), and the control circuit of 
those.
Desk/Large capacity tray (LCC)
5
Used to check the operations of the paper feed desk paper transport clutch (DTRC) and the LCC paper 
transport clutch (LTRC).
Desk/Large capacity tray (LCC)
10
LCT warm air heater temperature setting
LCT
11
LCT fan Duty setting
LCT
14
LCT temperature and humidity sensor monitor display
LCT
5
1
Used to check the operation of the display, LCD in the operation panel, and control circuit.
Operation panel
2
Used to check the operation of the heater lamp and the control circuit.
Fusing
3
Used to check the operation of the scanner lamp and the control circuit.
Scanner (reading)
4
Used to check the operation of the discharge lamp and the control circuit.
Process
6
1
Used to check the operations of the load in the paper transport system (clutches and solenoids) and the 
control circuits.
Paper transport/Paper exit section
2
Used to check the operations of each fan motor and its control circuit.
Others
3
Used to check the operations of the transport unit and the control circuit.
Process (Transport)
4
Used to check the cleaning operation of the PTC and the main charger.
Process
6
Used to perform fusing pressure release and applying, and to check the operations of the control circuits. Fusing
90
Used to reset the machine to the factory setting. (The scanner is set to the lock enable position)
Scanner
7
1
Used to set the operating conditions of aging.
Others
6
Used to set the operating intermittent aging cycle.
8
Used to display the warm-up time.
9
Color setting in the color copy test mode (Used to check the copy operation and the image quality for 
each color).
12
The document reading number of sheets setting (for aging operation)
DSPF
8
1
Used to check and adjust the operations of the developing voltage in each print mode and the control 
circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously.
Process (Developing)
2
Used to check and adjust the operation of the main charger grid voltage in each printer mode and the 
control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously.
Process (Charging)
6
Used to check and adjust the operation of the transport voltage and the control circuit.
Process (Transport)
10
Main charger total current output setting
Process
9
2
Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) 
and its control circuit.
Duplex
3
Used to check the operations of the load in the paper reverse section (duplex section) and its control 
circuit.
Duplex
10
1
Used to check the operations of the toner supply mechanism (toner motor) and the related circuit.
Toner supply section
2
Used to check the operations of the toner remaining quantity sensor and the control circuit.
Toner supply section
13
-
Used to cancel the self-diag "U1" trouble.
14
-
Used to cancel the self-diag H3, H4, H5 troubles.
15
-
Used to cancel the self-diag "U6" trouble.
LCC/LCT
16
-
Used to cancel the self-diag "U2" trouble.
MFP PWB / PCU PWB / SCU PWB
17
-
Used to cancel the self-diag "PF" trouble.
21
1
Used to set the maintenance cycle.
22
1
Used to check the print count value in each section and each operation mode. (Used to check the 
maintenance timing.)
2
Used to check the total number of misfeed and troubles. (When the number of total jam is considerably 
great, it is judged as necessary for repair.)
MX-7500N  SIMULATION  6 – 4
22
3
Used to check misfeed positions and the misfeed count of each position. 
* Presumption of the faulty point by this data is possible.
4
Used to check the trouble (self diag) history.
5
Used to check the ROM version of each unit (section).
Firmware
6
Used to output the setting/adjustment data (simulation, FAX soft switch, counter), the firmware version, 
and the counter list.
8
Used to check the number of operations (counter value) of the finisher, DSPF, and the scan (reading) unit.
9
Used to check the number of use (print quantity) of each paper feed section.
Paper feed, ADU, LCC
10
Used to check the system configuration (option, internal hardware).
12
Used to check the DSPF misfeed positions and the number of misfeed at each position. (When the 
number of misfeed is considerably great, it can be judged as necessary for repair.)
DSPF
13
Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge) and the 
fusing unit
Process
14
Used to display the use status of the toner cartridge.
Process
18
Used to display the user data delete history.
19
Used to check the values of the counters related to the scan - image send.
40
Used to display the error code list and the contents.
42
Used to check the JAM/trouble data.
43
JAM data details display
90
Used to output the various set data lists.
23
2
Used to output the trouble history list of paper jam and misfeed. (If the number of troubles of misfeed is 
considerably great, the judgment is made that repair is required.)
80
Used to check the operation of paper feed and paper transport in the paper feed section and the paper 
transport section. Used to output the list of the operation status of the sensor and the detectors in the 
paper feed section and the paper transport section.
Paper feed, Paper transport
24
1
Used to clear the jam counter, and the trouble counter. (After completion of maintenance, clear the 
counters.)
2
Used to clear the number of use (the number of prints) of each paper feed section.
3
Used to clear the finisher, DSPF, and the scan (reading) unit counter.
4
Used to clear the maintenance counter, the printer counters of the transport unit and the fusing unit. 
(After completion of maintenance, clear the counters.)
5
Used to clear the developer counter value and the toner hopper remaining quantity counter. 
(After replacing developer, clear these counters.)
6
Used to clear the copy counter.
Used to clear the counter value of the toner hopper remaining quantity. (Clear the data after replacing or 
cleaning the toner hopper.)
9
Used clear the printer mode print counter and the self print mode print counter.
12
Used to clear the document filing counter.
15
Used to clear the counters related to the scan mode and the image send.
35
Used to clear the toner cartridge use status data.
60
Used to clear the utility counter
25
1
Used to check the operations of the developing section.
Process (Developing section)
2
Used to make the initial setting of toner density when replacing developer. (Automatic adjustment)
Image process (Photoconductor/
Developing/Transfer/Cleaning)
4
Used to display the operation data of the toner supply quantity. (Not used in the market.)
Process
5
Used to display the toner density correction data. (Not used in the market.)
Process
26
1
Used to set Yes/No of installation of the right paper exit tray.
Paper exit
2
Used to set the paper size of the large capacity tray (LCC). (When the paper size is changed, this 
simulation must be executed to change the paper size in software.)
Paper feed
3
Used to set the specifications of the auditor. 
(Setting must be made according to the auditor use conditions.)
Auditor
5
Used to set the count mode of the total counter and the maintenance counter. (A3/11x17 size)
6
Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination.
7
Used to set the machine ID.
8
Counter mode setting (Long scale)
10
Used to set the trial mode of the network scanner.
18
Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.)
30
Used to set the operation mode corresponding to the CE mark (Europe safety standards). (For slow start 
to drive the fusing heater lamp)
32
Used to set the specifications of the fusing cleaning operation.
Fusing
35
Used to set the display mode of SIM 22-4 trouble history when a same trouble occurred repeatedly. There 
are two display modes: display as one trouble and display as several series of troubles.
38
Used to set Continue/Stop of print when the maintenance life is reached.
41
Used to set Enable/Disable of the magnification ratio automatic select function (AMS) in the center 
binding mode.
49
Used to set the print speed of postcards mode.
50
Used to set functions.
52
Used to set whether non-printed paper (insertion paper, cover paper) is counted up or not.
60
Used to set the utility counter mode.
61
Used to set the threshold of the coverage counter.
53
User auto color calibration (color balance adjustment) Inhibit/Allow setting.
65
Used to set the finisher alarm mode.
69
Used to set the operating conditions for toner near end.
Main
Sub
Functions
Section
Page of 127
Display

Sharp MX-6500N / MX-7500N (serv.man20) Service Manual ▷ Download

  • DOWNLOAD Sharp MX-6500N / MX-7500N (serv.man20) Service Manual ↓ Size: 1.13 MB | Pages: 127 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp MX-6500N / MX-7500N (serv.man20) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-6500N / MX-7500N (serv.man20) Copying Equipment. Information contained in Sharp MX-6500N / MX-7500N (serv.man20) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.