Sharp XG-V10XE (serv.man32) User Manual / Operation Manual ▷ View online
24
Scan Setting
This is a function by which this software automatically identifies and
controls all the projectors connected to the PC without setting the ports
and models. To use this function, the COM ports and
controls all the projectors connected to the PC without setting the ports
and models. To use this function, the COM ports and
IP address
to be
scanned with “Scan Setting” must be set beforehand.
See below about Scan Setting.
See below about Scan Setting.
1
Select “Scan Setting...” from the “File” menu.
Set the projector to be scanned here.
1
COM port enable/disable check box
2
Set the COM port Transmission Speed.
3
IP address input area
4
List of input IP addresses and enable/disable check box
5
Add button
When clicked after inputting the IP address, the address is added to
the list in
When clicked after inputting the IP address, the address is added to
the list in
4
.
6
Delete button
When clicked after selecting the IP address in
When clicked after selecting the IP address in
4
, that address is
deleted.
7
List of projectors whose IDs are redundant.
8
List of projectors whose IDs are missing.
9
Scan button
0
OK button
q
Cancel button
1
8
5
6
9
0
q
7
2
4
3
25
Adjusting and
Controlling
2
Set the port to which the projector is connected.
●
At
1
, check the check box of the COM port to which the projector
is connected.
●
To use a LAN, input the IP address at
3
, click the “Add” button,
then check the check box at
4
.
3
Click the “Scan” button.
The connected projectors are identified.
●
If projectors with the same IDs are discovered through scanning,
the data for those projectors is displayed in the “Redundant” area.
If this happens, reassign suitable IDs to the projectors.
the data for those projectors is displayed in the “Redundant” area.
If this happens, reassign suitable IDs to the projectors.
●
The results of scanning are compared with the pre-scanning All
Projector List and the data for projectors that could not be
confirmed as being connected is displayed in the “Missing” area.
Projector List and the data for projectors that could not be
confirmed as being connected is displayed in the “Missing” area.
4
Press “OK” if you wish to create an “All Projector List”
based on the results of scanning.
based on the results of scanning.
If you do not wish to create an “All Projector List”, press “Cancel”.
Deleting the set IP address
1
Select the IP address to be deleted at 4
4
4
4
4.
2
Click the “Delete” button.
LAN connections are possible when using the optional extension board
(AN-L10T).
The AN-L10T is scheduled for release in the near future.
(AN-L10T).
The AN-L10T is scheduled for release in the near future.
26
Projector Setting
When “Multiple Projector Operation Mode (Use ID Number)” is selected
at “Operation Mode Setting”, it is possible to add projectors manually
without using the scan setting automatic identification function. In
addition, when “Multiple Projector Operation Mode (Don’t Use ID
Number)” or “Single Projector Operation Mode” is selected, make the
respective settings at “Projector Setting”.
at “Operation Mode Setting”, it is possible to add projectors manually
without using the scan setting automatic identification function. In
addition, when “Multiple Projector Operation Mode (Don’t Use ID
Number)” or “Single Projector Operation Mode” is selected, make the
respective settings at “Projector Setting”.
Multiple Projector Operation Mode (Use ID Number)
1
From the “File” menu, select “Projector Setting”.
1
Select the ID number.
2
Select the port.
3
Select the transmission speed.
4
Input the IP address.
5
Enable/disable check box
6
Select the projector model.
7
Backup function enable/disable check box
8
Backup projector selection pull-down menu
9
Apply button.
2
Select the ID number.
3
Select the port to which the projector is connected.
If “LAN” is selected here, input the projector’s IP address.
1
2
3
4
5
6
8
7
9
27
Adjusting and
Controlling
4
Select the transmission speed between the computer and
the projector.
the projector.
●
Set the transmission speed set here and the transmission speed on
the projector to the same speed.
the projector to the same speed.
●
For instructions on the projector’s transmission speed setting, refer
to the projector’s operation manual.
to the projector’s operation manual.
5
Select the projector model and check the “Use Projector”
check box.
check box.
6
Set the backup projector.
If necessary, set the backup projector. See
page 44
for details.
7
Click the “Apply” button.
Multiple Projector Operation Mode (Don’t Use ID Number)
1
From the “File” menu, select “Projector Setting”.
2
Select the port to which the projector is connected.
3
Select the transmission speed between the computer and
the projector.
the projector.
●
Set the transmission speed set here and the transmission speed on
the projector to the same speed.
the projector to the same speed.
●
For instructions on the projector’s transmission speed setting, refer
to the projector’s operation manual.
to the projector’s operation manual.
4
Select the projector model and check the “Use Projector”
check box.
check box.
5
Set the backup projector.
If necessary, set the backup projector. See
page 44
for details.
6
Click the “Apply” button.
Click on the first or last page to see other XG-V10XE (serv.man32) service manuals if exist.