DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

MX-M565N  MX-RB22(PAPER PASS UNIT))  9-3

9) Install the unit (Packed item No.1) from the left side of the main

unit.

*Insert the unit along the rear wall of the main unit.

*Insert straight and carefully it not to contact the red circle posi-
tion.

*Fit the pawl at the upper portion of the cabinet at the left side
of the relay pass into the main unit cabinet.

10) Fix the left cabinet with screws in order of below.

11) Attach the lock holders (Packed item No.4) and fix with screws

(Packed item No.6). (Only for MX-FN10)

MX-M565N  MX-FN10  10 – 1

MX-M565N

Service Manual

 

* For removal of the saddle stitch finisher, manpower of two per-

sons or more is required.

1) Remove the fixing material, and remove the top case.

Remove the packing cushion and bundled items.

2) Holding the upper part of the saddle stitch finisher by two peo-

ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot.)

3)

Remove the skid and packing cushions.

4)

One person tilt the saddle stitch finisher, another person
remove the lower tray.

5)

Remove the other side similarly.

MX-M565N  MX-FN10  10 – 2

* The punch position labels (No.12 and No.13) should be kept at

hand since they will be necessary when installing the punch unit.

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

NOTE: Installing the MX-FN10 requires that the option desk and

paper pass unit be installed in advance.  Be sure to com-
plete the installation of the option desk and paper pass unit
before installing the saddle finisher.
Make sure that the connection plate provided on the front
side of the option desk is securely installed.
Make sure that the connection plate included in the pack-
age is securely installed.

NOTE: Check to confirm that the firmware version is later than

below.
If the version is older, upgrade the firmware.
Firmware version : 01.12.02.00

1)

Remove the Operation Manual storage cover on the left side of
the machine.

2)

Install the Operation Manual storage cover (which was
removed from the machine) to the saddle finisher.

1

Paper exit tray

1

2

Connection plate

1

3

Saddle tray

1

4

Paper holding A

1

5

Paper holding B

1

6

Fixing screw A

5

7

Fixing screw B

2

8

Fixing screw C

2

9

Staple cartridge

1

10

Staple position label (For scanner)

1

11

Staple position label (For RSPF/DSPF)

1

12

Punch position label (For scanner)

1

13

Punch position label (For RSPF/DSPF)

1

2

2

1

MX-M565N  MX-FN10  10 – 3

1) Engage the pawls (two positions) of the paper exit tray

(Packed items) on the finisher.
Fix the paper exit tray with fixing screws A (Packed items).

2) Fix the paper holding A with fixing screws A (Packed items).

3) Installation of two saddle tray (Packed items) and paper hold-

ing B (Packed items).

1) Insert the staple cartridge (Packed items).

1)

Put the finisher closer to the main unit, and check to insure that
the guide pin is smoothly inserted into the connection hole.

* If the guide pin is not inserted smoothly, perform the follow-

ing adjustment.

2)

Check that the alignment stamp on the center of the finisher is
fit with the alignment stamp on the main unit. 

1)

Loosen the fixing screw of the adjustment section on the rear
side. Adjust the height adjustment screw so that the guide pin
is fit with the connection hole in the finisher or the stamp on the
finisher is fit with the stamp on the main unit.
* By making space between the main body and ground, the

adjustment screw can be turned by the finger.

Guide pin

Connection hole

When installing the machine, 

check the stamp position

by opening the front door of 

FN10.