Sharp MX-M364N / MX-565N (serv.man5) Service Manual ▷ View online
MX-M565N MX-LC11 5 – 9
a. When the shift is in the front side
To adjust the print line in the direction A from the paper center as
shown in the figure:
1) Loosen two fixing screws (red screws) of the front/rear size
To adjust the print line in the direction A from the paper center as
shown in the figure:
1) Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction A (R side) by the shift amount, and tighten
the red fixing screws (2 for each). Move the auxiliary guide in
the direction A by the same size.
plate in the direction A (R side) by the shift amount, and tighten
the red fixing screws (2 for each). Move the auxiliary guide in
the direction A by the same size.
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
2) Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
shift. Repeat the procedures until there is no shift.
b. When the shift is in the rear side
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)
Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction B (F side) by the shift amount, and tighten
the red fixing screws (2 for each). Restore the stopper to the
original position, and fix it with the fixing screws. Move the aux-
iliary guide in the direction B by the same size.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
guide adjustment plate, and move the size guide adjustment
plate in the direction B (F side) by the shift amount, and tighten
the red fixing screws (2 for each). Restore the stopper to the
original position, and fix it with the fixing screws. Move the aux-
iliary guide in the direction B by the same size.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
2)
Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
A
R side
F side
B
R side
F side
MX-M565N MX-LT10 6 – 1
MX-M565N
Service Manual
[6] MX-LT10
1. Unpacking
A. Packed items check
2. Installation
Do not insert the finger in the hook part of the tray.
A. Long paper feeding tray attachment
1) Open the long paper feeding tray guide and hook it to the lock
of the long paper feeding tray.
2) Pull out the guide of the machine.
Do not pull out the MF tray unit with the guide.
3)
Hook the Long paper feeding tray to the guide of the machine.
4)
Insert the guide of the machine.
This tray can only be used for long paper feeding.
Do not leave long paper for an extended period of time.
You can use long paper with this tray.
No.
Name
Quantity
1
Long paper feeding tray
1
MX-M565N MX-FN17 7 – 1
MX-M565N
Service Manual
[7] MX-FN17
1. Unpacking
A. Packed items check
2. Installation
Check to confirm that the firmware version is later than below.
If the version is older, upgrade the firmware.
Firmware version : 01.07.03.00
If the version is older, upgrade the firmware.
Firmware version : 01.07.03.00
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Paper holding arm and paper exit full detection
actuator removal
1)
Remove the paper holding arm.
The paper holding arm must be removed together with the
paper holding arm holder. Since the paper holding arm is easy
to remove alone, be careful not to leave the paper holding arm
holder unremoved.
paper holding arm holder. Since the paper holding arm is easy
to remove alone, be careful not to leave the paper holding arm
holder unremoved.
2)
Remove the paper exit full detection actuator.
No.
Name
Quantity
1
Finisher
1
2
Attachment
1
3
Blinding bottom plate
1
4
Front rail guide
1
5
Path guide
1
6
Open/Close cover
1
7
Left rear cover
1
8
Punch F cover
1
9
Fulcrum upper cover
1
10
Take-up roller
1
11
Screw (M4 x 10 S tight)
1
12
Screw (M3 x 6 S tight, with flange)
4
13
Screw (M4 x 7 S tight)
5
14
Screw (M3 x 6 S tight)
3
15
Clip
1
16
Fulcrum shaft
1
17
Staple position label (For the scanner)
1
18
Staple position label (For the RSPF)
1
19
Safety cover
1
20
Protection sheet
1
11
12
13
14
15
16
17
18
19
20
2
1
4
3
5
8
9
10
6
7
MX-M565N MX-FN17 7 – 2
3) Pull and remove the delivery sponge.
Take care not to leave the fragment of the sponge.
B. External fixture removal
1) Open the front cabinet, and remove the front cabinet upper.
2) Remove the paper exit tray.
3) Remove the left cabinet.
4)
Remove the left cabinet upper.
C. Packed items attachment
1)
Attach the safety cover to the attachment, and fix it with the
screw (M3 x 6 S tight, with flange).
screw (M3 x 6 S tight, with flange).
2)
Attach the attachment.
1
2
2
1
1
2
1
2
Click on the first or last page to see other MX-M364N / MX-565N (serv.man5) service manuals if exist.