DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

MX-M565N  MX-LC11  5 – 5

3) Set the mark position ( ) of the auxiliary guide and the cas-

sette R to the size from A4 to LT, and fix with the fixing screw
(flat screw).

At that time, set the mark position ( ) of the auxiliary guide
and the cassette R to the same scale of the mark position ( )
of the side plate R and the size guide adjustment plate con-
firmed in procedure 1). (If the scale of the size guide adjust-
ment plate is at the center, set it to the center. If the size guide
adjustment plate is in 1mm in the front side, set it in 1mm in the
front side.)

c. Rear edge shaft switch
1) Remove the rear edge shift fixing screw (blue screw) which is

fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.

2) Tighten the removed rear edge shaft with the fixing screw

(blue), and store it in the storage space inside the front cabi-
net.

3)

Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.

At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.

4)

Slowly insert the tray to the original position.

A4

LT

MX-M565N  MX-LC11  5 – 6

1) Slowly pull out the tray until it stops.

2) Loosen the stopper fixing screw on the right lower side of the

tray so that the stopper does not function.

3) Pull out the tray again until it stops.

a. Side plate size switch
1) Remove four fixing screws (blue screws) which are fixing the

upper and the lower sections of the side plate F and the side
plate R.

2)

Adjust the mark position of the tray and the side plates in the
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).

Since the auxiliary guide setting is not required, fix the auxiliary
guide to either of A4 or LT. (To prevent against missing of the part)

c. Rear edge shaft switch
1)

Remove the rear edge shift fixing screw (blue screw) which is
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.

For the inch-series destinations, the auxiliary guide is not pro-
vided.

F side

R side

F side

R side

MX-M565N  MX-LC11  5 – 7

2) Insert the removed rear edge shaft into the mounting hole in

the paper feed base as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.

When the rear edge shaft is switched to B5, check to confirm
that the side plates F/R are already set to B5. If the side plates
F/R are not set to B5, the rear edge shaft cannot be switched
to B5.

3) Slightly push the tray, restore the stopper to the original posi-

tion, and fix the fixing screw.

At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.

4)

Slowly insert the tray to the original position.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

Execute SIM 26-2 "Size setting" with the key operations of the main
unit.
1)

The size selection menu of the large capacity tray is displayed
on the operation message display.

2)

Select a size button to be set on the message screen.

Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, perform the following adjustment procedures.
1)

Enter the SIM50-28 mode.

2)

Select [SETUP/PRINT] ADJ with the key button.

3)

Select [ALL] with the key button.

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

2&ǂ$'-

%.0$*ǂ$'-

63)ǂ$'-

6(78335,17ǂ$'-

5(68/7

'$7$

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

/($'

2))6(7

$//

MX-M565N  MX-LC11  5 – 8

By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.

-  [LEAD]: Print image lead edge image position adjustment

-  [OFFSET]: Print image off-center adjustment

When [ALL] is selected, both of the above two items are
executed simultaneously.

4) Select a paper feed tray to be adjusted.

5) Press [EXECUTE] key.

The adjustment pattern is printed out.

6) Set the adjustment pattern on the document table. (Any direc-

tion)

Fit the adjustment pattern correctly with the document guide.

7) Press [EXECUTE] key.

The following item is automatically adjustment.

-  Print image lead edge image position adjustment

-  Print image off-center adjustment

8) Press [OK] key.

The adjustment result becomes valid.

Perform procedures 4) to 7) for each paper feed tray.

Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
removed, perform the following adjustment procedures.
1)

Slowly pull out the tray until it stops.

2)

Loosen the stopper fixing screw on the right lower side of the
tray so that the stopper does not function.

3)

Pull out the tray again until it stops.

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

(;(&87(

0)7

&6

$'8

&6

&6

&6

/&&