Sharp MX-M364N / MX-565N (serv.man5) Service Manual ▷ View online
MX-M565N MX-DE20 (STAND500&2000 SHEET PAPER DRAWER) 4 – 2
Place the main unit on the desk unit slowly by fitting the exter-
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning groove of
the main unit.
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning groove of
the main unit.
2) Remove the tray 1 and the desk tray.
3) Raise the linkage plates on the right and left sides of the front
side of the desk unit, and fix the connection plate FL(Packed
items No.5) and the connection plate FR(Packed items No.6)
with the fixing screws (Packed items No.2 M4x8, Packed items
No.3 M3x8).
* Note that the shape of the connection plates are different.
items No.5) and the connection plate FR(Packed items No.6)
with the fixing screws (Packed items No.2 M4x8, Packed items
No.3 M3x8).
* Note that the shape of the connection plates are different.
4)
Attach the tray 1 and the desk tray.
5)
Raise the linkage plates on the right and left sides of the rear
side of the desk unit, and fix the connection plate RL (Packed
items No.7) and the connection plate RR (Packed items No.8)
with the fixing screws (Packed items No.2 M4x8, Packed items
No.3 M3x8).
* Note that the shape of the connection plates are different.
side of the desk unit, and fix the connection plate RL (Packed
items No.7) and the connection plate RR (Packed items No.8)
with the fixing screws (Packed items No.2 M4x8, Packed items
No.3 M3x8).
* Note that the shape of the connection plates are different.
6)
Attach the connection cover included in the package.
3
1
FL(No.5)
2
3
1
FR(No.6)
2
RL(No.7)
RR(No.8)
3
3
1
2
1
RR(No.8)
RL(No.7)
2
MX-M565N MX-DE20 (STAND500&2000 SHEET PAPER DRAWER) 4 – 3
C. Release the lock
1) Pull out each tray. Turn and remove the fixing material, and
remove the caution sheet.
Attach the removed fixing material to the position shown in the
figure for storage.
Close the cassette which was pulled out.
Attach the removed fixing material to the position shown in the
figure for storage.
Close the cassette which was pulled out.
Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
2) Pull out the tandem tray. Remove the four screws and remove
the caution sheet.
D. Connector connection
1)
Remove the cover from the rear side of the machine.
2)
Connect the connector.
3)
Split the removed cover along the perforated line.
4)
Attach the cover.
E. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
1
2
2
1
MX-M565N MX-DE20 (STAND500&2000 SHEET PAPER DRAWER) 4 – 4
F. Tray setup
(1) System setting
1) Touch the [Paper Tray Settings] key.
2) Touch the [Paper Tray Settings] key to configure the settings.
2) Touch the [Paper Tray Settings] key to configure the settings.
These settings specify the paper type, paper size, and func-
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.
3) Touch the [Change] key in the above screen to change the set-
tings. The following settings can be configured.
(2) Tray size setup
a. Tray 2
1) Pull out the paper tray.
1) Pull out the paper tray.
Gently pull the tray out until it stops.
If paper remains in the tray, remove it.
If paper remains in the tray, remove it.
2) Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.
b. Inch series tray 3, tray 4 (LT to A4)
1)
1)
Open the tandem paper feed tray.
2)
Push down the paper feed base plate gently, hold the hooks
and remove A4 size regulation plate.
and remove A4 size regulation plate.
3)
Fit the A4 size regulation plate to A4 size, and attach it.
* Be careful to place and direction that install the sheet.
* Be careful to place and direction that install the sheet.
4)
Close the tandem paper feed tray.
5)
Execute SIM26-2 to set tray size for Tray3.
Item
Description
Type
Select the type of paper that is loaded in the tray.
The paper types that can be selected vary by paper
tray.
The paper types that can be selected vary by paper
tray.
Size
Select the paper size from the list. The paper sizes
that can be selected vary by tray. The sizes that
can be selected may also be restricted by the paper
type selected above.
If the desired size does not appear in the list, select
[Custom Size] and directly enter the size (only for
the bypass tray).
that can be selected vary by tray. The sizes that
can be selected may also be restricted by the paper
type selected above.
If the desired size does not appear in the list, select
[Custom Size] and directly enter the size (only for
the bypass tray).
Feeding Approved
Job
Job
Select the modes that can be used. If there is a
function that you do not wish to be used with the
selected tray, disable the function. When the "Type"
is other than plain paper, recycled paper, colored
paper, or a user type, [Fax] and [Internet Fax]
cannot be selected.
function that you do not wish to be used with the
selected tray, disable the function. When the "Type"
is other than plain paper, recycled paper, colored
paper, or a user type, [Fax] and [Internet Fax]
cannot be selected.
A
B
1
1
3
3
3
3
2
2
MX-M565N MX-DE20 (STAND500&2000 SHEET PAPER DRAWER) 4 – 5
G. Image off-center adjustment
The image lead edge position and the off-center adjustment value
of the desk unit have been set to the average value when shipping
from the factory.
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.
of the desk unit have been set to the average value when shipping
from the factory.
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.
1) Enter the SIM50-28 mode.
2) Select [SETUP/PRINT] ADJ with the key button.
3) Select [ALL] with the key button.
3) Select [ALL] with the key button.
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
can be executed individually.
- [LEAD]: Print image lead edge image position adjustment
- [OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
executed simultaneously.
4) Select a paper feed tray to be adjusted.
5) Press [EXECUTE] key.
The patch image (adjustment pattern) is printed out.
6) Set the adjustment pattern on the document table.
Fit the adjustment pattern correctly with the document guide.
In this case, put 5 sheets of white paper on the printed adjust-
ment pattern.
In this case, put 5 sheets of white paper on the printed adjust-
ment pattern.
7)
Press [EXECUTE] key.
The following item is automatically adjustment.
The following item is automatically adjustment.
- Print image lead edge image position adjustment
- Print image off-center adjustment
8)
Press [OK] key.
The adjustment result becomes valid.
The adjustment result becomes valid.
Perform procedures 4) to 7) for each paper feed tray.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
2&ǂ$'-
%.0$*ǂ$'-
63)ǂ$'-
6(78335,17ǂ$'-
5(68/7
'$7$
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
/($'
2))6(7
$//
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
$872,0$*(326,7,21$'-8670(176(59,&(
(;(&87(
0)7
&6
$'8
&6
&6
&6
/&&
Click on the first or last page to see other MX-M364N / MX-565N (serv.man5) service manuals if exist.