DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

MX-M565N  MX-LC11  5 – 1

MX-M565N

Service Manual

 

Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.

1) Remove the paper feed base fixing screw.

Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on without
removing the fixing screw, a trouble may be resulted.

1)

Attach the mounting plate upper to the right side of the main
unit with the fixing screw A.

When attachment, put the rubber section of the mounting plate
upper on the lower side.

2)

Remove the right door cover from the machine.

3)

Remove the screw cap, and remove the screw.

1

Large capacity tray unit

1

2

Mounting plate upper

2

3

Connection unit

1

4

Fixing screw A (Hexagon with seat, S-tight, M4 x 35)

4

5

Fixing screw B (Hexagon with seat, S-tight, M4 x 12)

2

6

Fixing screw C (screw 4 x 8 cup)

1

2

1

4

5

3

6

MX-M565N  MX-LC11  5 – 2

4) Remove the cover.

5) Temporarily fix the fixing screw B midway.

6) Insert the temporarily fixed screw B into the key hole in the

connection unit, and temporarily fix the connection unit.

7) Fix the other fixing screw B, and tighten the temporarily fixed

screw B securely.

8)

While lifting the section marked with O, insert the connection
unit into the large capacity tray unit, and fix the fixing screw C
at the mark A on the connection unit.

1)

Put the large capacity tray unit closer to the main unit.

2)

Check to insure that the height adjustment check rib of the
large capacity tray unit and the axis line of the mounting plate
upper mounted to the main unit are in the same line.

[Shift to the left]

[Shift to the right]

MX-M565N  MX-LC11  5 – 3

3) If the height adjustment is not required, insert the large capac-

ity tray unit further more.
If the height adjustment is required, perform the adjustment
procedures from 4).

4) Loosen the adjustment screw on the F side.

Use the adjustment screw on the front side for the adjustment.
Do not touch the screw on the rear side.

If the screw is loosened or removed when servicing, be sure to
execute “C. Height adjustment” after completion of servicing.

5) In the case of a shift to the right, press the front upper section

and fit the height adjustment check rib so that it is in the same
line with the axis line of the mounting plate upper. Insert the
large capacity tray unit into the main unit.

6)

In the case of a shift to the left, lift the grip so that the height
adjustment check rib is in the same line with the axis line of the
mounting plate upper, and insert the large capacity tray unit.

7)

Tighten the loosened screw.

1)

Remove the connector cover.
If the dehumidifier heater kit is not installed, there is no need to
remove the connector cover on the lower side.

2)

Connect the connector, and tighten the screw.
If the dehumidifier heater kit is not installed, there is no need to
connect the dehumidifier heater connector to the connector on
the lower side.

MX-M565N  MX-LC11  5 – 4

Since the factory setting of the paper size is A4, if paper size switch
is required, perform the following procedures.

1) Slowly pull out the tray until it stops.

2) Loosen the stopper fixing screw on the right lower side of the

tray so that the stopper does not function.

3) Pull out the tray again until it stops.

a. Side plate size switch
1)

Remove four fixing screws (blue screws) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.

2)

Adjust the mark position of the tray and the side plates in the
lower section of the side plates F/R according to the desired
size. Also adjust the upper section according to the desired
size, and fix with the four fixing screws (blue screws).

b. Auxiliary guide size switch
1)

When switching the size of the side plate R, check to confirm
the mark position ( ) of the side plate R and the size guide
adjustment plate.

2)

Loosen the fixing screw (flat screw 1pc) of the auxiliary guide.

F side

R side

F side

R side