DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

MX-M565N  MX-DE12/DE13/DE14 (STAND/1X500/2X500/3X500 SHEET PAPER DRAWER)  3 – 2

3)

Raise the linkage plates on the right and left sides of the front
side of the desk unit, and fix them with the fixing screws
included in the package.

4)

Attach the tray 1 and the tray 2.

5)

Raise the linkage plates on the right and left sides of the rear
side of the desk unit, and fix them with the fixing screws
included in the package.

6)

Attach the connection cover included in the package.

1)

Pull out each tray. Turn and remove the fixing material, and
remove the caution sheet.
Attach the removed fixing material to the position shown in the
figure for storage.
Close the cassette which was pulled out.

Before turning on the power, check to insure that the fixing
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.

1)

Remove the cover from the rear side of the machine.

MX-M565N  MX-DE12/DE13/DE14 (STAND/1X500/2X500/3X500 SHEET PAPER DRAWER)  3 – 3

2)

Connect the connector.

3)

Split the removed cover along the perforated line.

4)

Attach the cover.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

For setting the tray size, refer to “Tray size setup” (1-6).

The image lead edge position and the off-center adjustment value
of the desk unit have been set to the average value when shipping
from the factory. 
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.

2)

Enter the SIM50-28 mode.

3)

Select [SETUP/PRINT] ADJ with the key button.

4)

Select [ALL] with the key button.

By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.

-  [LEAD]: Print image lead edge image position adjustment

-  [OFFSET]: Print image off-center adjustment

When [ALL] is selected, both of the above two items are
executed simultaneously.

5)

Select a paper feed tray to be adjusted.

6)

Press [EXECUTE] key.

The patch image (adjustment pattern) is printed out.

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

2&ǂ$'-

%.0$*ǂ$'-

63)ǂ$'-

6(78335,17ǂ$'-

5(68/7

'$7$

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

/($'

2))6(7

$//

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$872,0$*(326,7,21$'-8670(176(59,&(

(;(&87(

0)7

&6

$'8

&6

&6

&6

/&&

MX-M565N  MX-DE12/DE13/DE14 (STAND/1X500/2X500/3X500 SHEET PAPER DRAWER)  3 – 4

7)

Set the adjustment pattern on the document table.

Fit the adjustment pattern correctly with the document guide.
In this case, put 5 sheets of white paper on the printed adjust-
ment pattern.

8)

Press [EXECUTE] key.

The following item is automatically adjustment.

-  Print image lead edge image position adjustment

-  Print image off-center adjustment

9)

Press [OK] key.

The adjustment result becomes valid.

Perform procedures 4) to 7) for each paper feed tray.

MX-M565N  MX-DE20 (STAND500&2000 SHEET PAPER DRAWER)  4 – 1

MX-M565N

Service Manual

 

If the connector is removed first, it may be damaged during the
installation procedures. Therefore, keep it packed while un-box-
ing.  and unpack it only when connecting the connector to the
machine.

Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation. 

1)

Turn each adjuster to fix the desk unit.

1)

Put the main unit on the desk unit.

Use man power of four persons or more to lift the main unit.

1

Desk unit

1

2

Fixing screws (M4 x 8)

4

3

Fixing screws (M3 x 8)

4

4

Connection cover

2

5

Connection plate FL

1

6

Connection plate FR

1

7

Connection plate RL

1

8

Connection plate RR

1