Sharp MX-M364N / MX-565N (serv.man5) Service Manual ▷ View online
MX-M565N MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series 1 – 6
3)
Insert the cartridge securely until it locks.
E. Tray setup
(1)
Tray size setup
1)
Pull out the paper tray.
Gently pull the tray out until it stops.
If paper remains in the tray, remove it.
2)
Adjust the guide plates A and B by squeezing their lock levels
and sliding them to match the vertical and horizontal dimen-
sions of the proper to be loaded.
The guide plates A and B are slidable, slide each guide plate
while squeezing lock lever.
and sliding them to match the vertical and horizontal dimen-
sions of the proper to be loaded.
The guide plates A and B are slidable, slide each guide plate
while squeezing lock lever.
F. Image quality check
Be sure to check the following items related to image quality. For
details of the adjustment and checking procedures, refer to the “[5]
ADJUSTMENT” on the Service Manual.
details of the adjustment and checking procedures, refer to the “[5]
ADJUSTMENT” on the Service Manual.
Check that the following items are within specification. If not, carry
out the adjustment.
out the adjustment.
NOTE: When installing the copier, be sure to carry out the copy
gray balance and the printer gray balance.
(1)
Image loss, void area (see ADJ 9)
(2)
Copy gray balance (11-A / Auto adjustment)
1)
Enter the SIM 46-74 mode.
2)
Press [EXECUTE] button.
The high density process control is performed, and the copy
gray patch image (adjustment pattern) is printed out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
gray patch image (adjustment pattern) is printed out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
3)
Set the gray patch image (adjustment pattern) paper printed in
procedure 2) on the document table.
procedure 2) on the document table.
Set the gray patch image (adjustment pattern) printed in the
procedure 2) on the document table.
procedure 2) on the document table.
Place the gray patch image so that the fine lines are on the left
side.
side.
At that time, place 5 sheets of white paper on the printed gray
patch image (adjustment pattern).
patch image (adjustment pattern).
A
B
MX-M565N MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series 1 – 7
4)
Press [EXECUTE] button.
The copy density and gradation adjustment is performed auto-
matically, and the adjustment pattern is printed.
matically, and the adjustment pattern is printed.
If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.
tern, check the print engine for any problems.
5)
Press [EXECUTE] key.
The printer gray patch image (adjustment pattern) is printed
out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
6)
Set the gray patch image (adjustment pattern) printed in the
procedure 5) on the document table.
procedure 5) on the document table.
Set the gray patch image (adjustment pattern) printed in the
procedure 2) on the document table.
procedure 2) on the document table.
Place the gray patch image so that the fine lines are on the left
side.
side.
At that time, place 5 sheets of white paper on the printed gray
patch image (adjustment pattern).
patch image (adjustment pattern).
7)
Press [EXECUTE] key.
The printer gray balance adjustment (step 1) is automatically
performed and the gray balance check patch image is printed
out.
performed and the gray balance check patch image is printed
out.
If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.
tern, check the print engine for any problems.
8)
The initial setting menu of the halftone image correction is dis-
played.
played.
Press [OK] key.
The initial setting of the halftone image correction is per-
formed.
formed.
3
1 2
0
/
.
-
,
+
*
)
(
'
&
%
$
#
*KIJFGPUKV[
.QYFGPUKV[
Უȷ6JGRCVEJFGPUKV[KUKFGPVKECNDGVYGGPRCVEJGUQTPQVTGXGTUGF
ȷ6JGRCVEJFGPUKV[KUEJCPIGFITCFWCNN[
Უ6JGOCZFGPUKV[UGEVKQPKUPQVDNWTTGF
Უ2CVEJ%QT&KUXGT[UNKIJN[EQRKGF
3
1 2
0
/
.
-
,
+
*
)
(
'
&
%
$
#
*KIJFGPUKV[
.QYFGPUKV[
Უȷ6JGRCVEJFGPUKV[KUKFGPVKECNDGVYGGPRCVEJGUQTPQVTGXGTUGF
ȷ6JGRCVEJFGPUKV[KUEJCPIGFITCFWCNN[
Უ6JGOCZFGPUKV[UGEVKQPKUPQVDNWTTGF
Უ2CVEJ#QT$KUXGT[UNKIJN[EQRKGF
MX-M565N MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series 1 – 8
9)
Wait until [EXECUTE] key is displayed.
When it is displayed, press it.
The halftone image correction is performed.
10) When "COMPLETED THIS PROCEDURE" is displayed, the
adjustment operation is completed.
Cancel SIM46-74.
NOTE: The adjustment result becomes valid only when the both
adjustments in the copy mode and in the printer mode are
completed.
For example, if the copy gray balance adjustment (auto-
matic adjustment) is performed and the simulation is can-
celed, the adjustment result is invalid.
completed.
For example, if the copy gray balance adjustment (auto-
matic adjustment) is performed and the simulation is can-
celed, the adjustment result is invalid.
11) Check the copy gray balance and density.
(Refer to the item of the copy gray balance and density check.)
When the gray balance and the density are unsatisfactory after
the automatic adjustment by selecting the factory target in pro-
cedure 4), execute the manual gray balance adjustment
(ADJ11C (2)).
the automatic adjustment by selecting the factory target in pro-
cedure 4), execute the manual gray balance adjustment
(ADJ11C (2)).
Also when the service target is selected in procedure 4) to exe-
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11C (2)).
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11C (2)).
12) Check the printer gray balance and density.
(Refer to the item of the printer gray balance and density
check.)
check.)
If a satisfactory result on the gray balance and the density is
not obtained with the automatic adjustment, execute the man-
ual adjustment (SIM 67-25) (ADJ 11E (2)).
not obtained with the automatic adjustment, execute the man-
ual adjustment (SIM 67-25) (ADJ 11E (2)).
Also when the service target is selected in procedure 7) to exe-
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11E (2)).
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11E (2)).
If the gray balance or density is not in the satisfactory level
even after execution of the automatic and manual adjustments,
there may be another cause.
even after execution of the automatic and manual adjustments,
there may be another cause.
Troubleshoot the cause, repair or perform necessary works,
and repeat the adjustment from the beginning.
and repeat the adjustment from the beginning.
MX-M565N Dehumidifying heater 2 – 1
MX-M565N
Service Manual
[2] Dehumidifying heater
1. Parts list
Kit name
Kit code
No.
Part name
Part code
Price rank
Q'ty
Heater electric
component kit
component kit
DKIT-0425FCZZ
1
Dehumidifier heater control switch
QSW-C9294QCZZ
AF
1
2
Dehumidifier heater control switch label
TLABZ5256FCZZ
AH
1
3
Supporter LSUPP0140FCPZ
AC
4
4
WH PWB
CPWBF1935FCE1
AW
1
5
WH harness
DHAI-4701FCPZ
BF
1
6
Clamp
LHLDW2037FCPZ
AC
1
7
Screw
XBPS730P08KS0
AB
1
8
Washer
XWHS730-05080
AA
2
DH POWER
1
3
2
4
7
5
6
8
Kit name
Kit code
No.
Part name
Part code
Price rank
Q'ty
Heater kit
DKIT-0426FCZZ
(120V series)
DKIT-0426FC11
(230V series)
(120V series)
DKIT-0426FC11
(230V series)
1
Heater (120V series)
RHETP0166FCPZ
BA
1
Heater (230V series)
RHETP0167FCPZ
BA
2
Heater mounting plate
LPLTM6089FCZ2
AK
1
3
Heater mounting plate
LPLTM8118FCZZ
AN
1
4
Screw (M3 x 6 S-tight)
XHBS730P06000
AC
3
5
Screw
XEBS740P10000
AA 1
6
Screw
XBPS730P08KS0
AB 2
7
Clamp
LHLDW1013FCZZ
AB 1
8
CSS-WH harness
DHAI-4711FCPZ
AN
1
9
Washer
XWHS730-05080
AA
2
1
8
2
3
4
5
6
7
9
Click on the first or last page to see other MX-M364N / MX-565N (serv.man5) service manuals if exist.