DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

Model
MX-M364N MX-565N (serv.man5)
Pages
127
Size
45.47 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual (Revised January2016).
File
mx-m364n-mx-565n-sm5.pdf
Date

Sharp MX-M364N / MX-565N (serv.man5) Service Manual ▷ View online

MX-M565N  MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series  1 – 2
(2)
Dust
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
(3)
Direct rays of the sun
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
(4)
Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5)
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
1)
When in transit or storing, put the parts in an anti-static bag or
an anti-static case and do not touch them with bare hands.
2)
When and after removing the parts from an anti-static bag
(case), use an earth band as shown below:
-  Put an earth band to your arm, and connect it to the
machine.
-  When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
MX-M565N  MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series  1 – 3
G. Note for handling the drum unit, the transfer 
unit, the developing unit, and the fusing unit
When handling the OPC drum unit, the transfer unit, and the devel-
oping unit, strictly observe the following items.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
(Drum unit)
1)
Avoid working at a place with strong lights.
2)
Do not expose the OPC drum to lights including interior lights
for a long time.
3)
When the OPC drum is removed from the machine, cover it
with light blocking material. (When using paper, use about 10
sheets of paper to cover it.)
4)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the OPC drum surface.
(Transfer unit)
1)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the transfer roller.
(Developing unit)
1)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the developing unit.
(Fusing unit)
1)
Be careful not to put fingerprints, oil, grease, or other foreign
material on the fusing roller and the external heating belt.
2)
Do not leave the fusing roller in contact state for a long time.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
3. Unpacking
A. Unpacking procedure
1)
Remove the PP band.
2)
Remove the internal packing pads with the machine.
B. Removal of the fixing tape and protection 
material
C. Removal of parts packed together
No.
Content
Method
1
Implements, facility, 
and man power
Use a forklift. (If no forklift is available, 
manpower of two persons is required.) 
2
Delivery
Transit must be made in packed condition.
MX-M565N  MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series  1 – 4
D. Check the parts packed item
1)
Check that all the parts are in the package.
4. Installation
<Note before installation>
* When connecting the main unit with the optional STAND/1 X 500/
2X500/3X500 SHEET PAPER DRAWER or STAND/500&2000
SHEET PAPER DRAWER, first unpack and install the PAPER
DRAWER; then unpack the main unit and securely place the
main unit on the PAPER DRAWER before installing the main
unit.
A. Lock release
(1)
Tray rotation plate lock release
1)
Pull out the tray, and remove the rotation plate fixing material
and the tray note label.
2)
Attach the removed fixing material to the position shown in the
figure for storage.
(2)
Scanner (2/3 mirror unit) lock release
1)
Remove the optical unit fixing screw, and remove the note
label.
(3)
Removal of the drum protection sheet.
1)  Open the right door and pull out the drum protection sheet from
     transfer roller.
(4)
Removal of the fusing heat roller protector and 
push down the pressure release lever to apply 
pressure
B. Developer supply
Be careful not to put fingerprints or oil dirt on the roller surface.
Do not hold the case adjacent to the DV roller strongly.
1)
Open the front cabinet, and remove the waste toner box.
2)
Remove the fixing screw of the developing unit, and pull out
the developing unit.
NO.
Parts name
Quantity
1
Operation manual
1
1
2
1
3
MX-M565N  MX-M365N/M465N/M565Nseries MX-M364N/M464N/M564Nseries AR-M460N/M560N series  1 – 5
3)
Remove two screws. Remove the DV cover.
4)
While supplying developer from the developer supply port of
the developing unit, turn the MC gear counterclockwise by
using UKOG-0341FCZZ to supply all developer to the devel-
oping unit.
* Before opening the developer bag, shake the bag to mix
toner and developer in the bag, and then supply developer
to the developing unit.
5)
Attach the DV cover to the machine.
* Check to confirm that the pawl is securely engaged.
6)
Insert the developing unit into the machine, and fix it with the
blue screw.
7)
Install the waste toner box.
C. Toner density reference control level setting
NOTE: Execute Toner density reference control level setting
without installing the toner cartridge.
1)
Insert the power plug into a power outlet. With the front cabinet
open, turn ON the power switch of the machine and the power
switch on the operation panel.
2)
With the front cabinet open, enter SIM 25-2.
WARNING: Do not install the toner cartridge before complet-
ing the Toner density reference control level setting (SIM 25-2).
3)
Close the front cabinet.
4)
After completion of the adjustment of the toner density control
reference value, insert the toner cartridge.
5)
When [EXECUTE] key is pressed, it is highlighted. The devel-
oping roller rotates, and the toner density sensor detects toner
density, and the output value is displayed.
The above operation is executed for 2 minutes, and the aver-
age value of the toner density sensor detection level is set
(saved) as the reference toner density control value.
When the reference toner density control adjustment operation
is completed, [EXECUTE] key returns to normal from highlight.
This indicates whether the adjustment operation is completed
or not.
6)
Press the CA key to exit the simulation.
NOTE:
If the operation is interrupted within 2 minutes, the adjustment
result is not reflected.
When [EXECUTE] key is pressed during rotation, the opera-
tion is stopped and [EXECUTE] key returns to the normal dis-
play.
If [EE-EU] or [EE-EL] is displayed, setting of the reference
toner density control value is not completed normally.
NOTE: When not replacing the developer, don’t execute SIM25-2.
Only execute SIM 25-2 when replacing the Developer.
SIM 25-2 should only be run immediately after installing
new DV material.
Toner Concentration Reference Control Level Setting will
be incorrect if SIM 25-2 is performed at any other time.
D. Install toner cartridge
1)
Shake the toner cartridge several times.
2)
Open the front cabinet, and insert the toner cartridge.
* Do not forcibly insert the toner cartridge.
Keep holding the cartridge and completely insert it.
* When the machine is transported with the developing unit
removed, be sure to remove the toner cartridge. (If not, toner
may be clogged.)
Error display
Content
Details of content
EE-EL
EL abnormality
Sensor output level less than 77, or 
sensor control voltage level over 207
EE-EU
EU abnormality
Sensor output level over 177, or sensor 
control voltage level less than 52
EE-EC
EU abnormality
Sensor output level less than 128, or 
sensor control voltage level over 131
Page of 127
Display

Click on the first or last page to see other MX-M364N / MX-565N (serv.man5) service manuals if exist.