DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

MX-M565N  MX-FN10  10 – 4

2) Remove the two screws, and remove the front under cover

and foot cover.

3) Loosen the fixing screw of the adjustment section on the front

side. If the guide pin is inserted smoothly or the stamp on the
finisher is fit with the stamp on the main unit, tighten the fixing
screws of the adjustment section on the front/rear sides.
* By making space between the main body and ground, the

adjustment screw can be turned by the finger.

1) Insert the finisher into the main unit. Check to insure that the

upper and lower clearances between the main unit and the fin-
isher are even.

2)

If the upper and lower clearances between the main unit and
the finisher are not even, remove the screw (one for each) of
the foot covers on the front/rear sides, and remove the foot
cover.

3)

Loosen four fixing screws of the adjustment section, and turn
the height adjustment screws on the front/rear sides to adjust
so that the clearances are even.
* By making space between the main body and ground, the

adjustment screw can be turned by the finger.

4)

When the clearances are even, tighten the fixing screw of the
adjustment section, and install the foot cover.

Clearance

Clearance

MX-M565N  MX-FN10  10 – 5

1) Fix the connection plate (Packed items) to the paper feed desk

with fixing screws B (Packed items).

2) Install the rail bracket to the frame with fixing screws C

(Packed items).

1) Connect the finisher connector with the connector of the inter-

face pass unit, and tighten the screw.

2)

Connect the finisher connector with the connector of the main
unit, and tighten the screw.

1)

Attach the staple position label (Packed items) to the position
indicated in the figure.
For scanner

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

Fit with the corner R.

Label attachment reference

*Corner of the upper 
cabinet bottom

Fit with the corner R.

DSPF

RSPF

Cleaning of the document scan section

CAUTION

When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).

MX-M565N  MX-PNX5A/B/C/D  11 – 1

MX-M565N

Service Manual

 

Use the punch position labels bundled with the MX-FN10.

Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.

1) Disconnect the connector between the main unit and the sad-

dle finisher.

2)

Release the lock and separate the saddle finisher from the
main unit.

1)

Remove the rear cover.

2)

Remove the front lower cover.

1

Punch  unit

1

2

Harness A (Purple)

1

3

Harness B (Gray)

1

4

Punch jam processing label

1

000-0000

1

3

2

4

MX-M565N  MX-PNX5A/B/C/D  11 – 2

3) Open the front cover and remove the front inner cover.

1) Remove the dummy punch guide. 

2)

Attach the punch unit to the saddle finisher. 
Fix the punch unit with the screw which was removed from the
dummy punch guide.

Before installing, remove the dust box. 

Check to confirm that the punch guide pin is securely inserted
into the guide pin insertion hole of the finisher.

Check to confirm that the pawl (A) is engaged with the plate
frame. 

3)

Connect the harness on the punch unit side with the PWB on
the finisher side.