Sharp MX-M364N / MX-565N (serv.man5) Service Manual ▷ View online
MX-M565N MX-FN11 (FINISHER) 12 – 3
2. Installation
NOTE: Check to confirm that the firmware version is later than
below.
If the version is older, upgrade the firmware.
Firmware version : 01.06.02.00
NOTE: When the finisher is installed, first install the paper pass
unit, and then install the finisher.
NOTE: When the finisher and punch unit is installed at the same
time, first install the punch unit, and then install the finisher.
A. Replacement of the Operation Manual storage
cover
1)
Remove the Operation Manual storage cover on the left side of
the machine.
the machine.
2)
Install the Operation Manual storage cover (which was
removed from the machine) to the finisher.
removed from the machine) to the finisher.
B. Installation of the rail
1)
Install the rail (Packed items) to the finisher with the fixing
screws (Packed items).
screws (Packed items).
2)
Install the rail reception sheet metal (Packed items) to the main
unit with the fixing screws (Packed items).
unit with the fixing screws (Packed items).
C. Installation of the connection fixture F/R
1)
Install the connection fixture R (Packed items) to the main unit
with the fixing screws (Packed items).
with the fixing screws (Packed items).
2)
Install the connection fixture F (Packed items) to the main unit
with the fixing screws (Packed items).
with the fixing screws (Packed items).
2
2
1
MX-M565N MX-FN11 (FINISHER) 12 – 4
D. Attaching the cushion
1)
Attach the cushion (S) (Packed items), the cushion (M)
(Packed items) and the cushion (L) (Packed items) to the posi-
tion indicated in the figure.
(Packed items) and the cushion (L) (Packed items) to the posi-
tion indicated in the figure.
E. Check of the connected position of main unit
and finisher
1)
Insert the rail of the finisher into the slit on the rail reception
sheet metal of the main unit, install the finisher.
sheet metal of the main unit, install the finisher.
2)
Remove the screw, and remove the connector cover on rear
side of the finisher.
side of the finisher.
3)
Check that the center of the screw hole of the finisher is in the
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
* When not the range of specification, progress to the proce-
dure of "I. Adjustment".
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.
F. Adjustment
1)
Remove the finisher from the main unit.
#USHION
2EFER
ENCE
2EFERENCE
#USHION
#USHION
2EFERENCE
2EFER
ENCE
2EFERENCE
2EFER
ENCE
MX-M565N MX-FN11 (FINISHER) 12 – 5
2)
Remove the screw, slide to the left the front lower cover, and
remove it.
remove it.
3)
Open the front upper door, and remove the screw.
4)
Remove the screws, and open the front cover.
5)
Remove the fixing tapes.
6)
Remove the screws, and remove the auxiliary wheels.
7)
Remove the screws, and remove the rear lower cover.
8)
Remove the fixing tapes.
MX-M565N MX-FN11 (FINISHER) 12 – 6
9)
Loosen both of the caster fixing screws of the front side and
rear side.
rear side.
10) Remove the screw, and remove the spanner installed inside
the front lower door.
11) Turn the bolt for which the adjustment is necessary, and adjust
to become it within the range of specification.
12) Check to insure that the upper and lower clearances between
the main unit and the finisher are even.
Click on the first or last page to see other MX-M364N / MX-565N (serv.man5) service manuals if exist.