Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ▷ View online
MX-M1205 Dehumidifying heater kit 3 – 4
6)
Attach the cover which is removed in step 4).
NOTE: When installing, be careful that does not pinch the har-
ness.
7)
Attach the snap band and arrange the wires.
NOTE: When installing, be careful in the direction of the snap
band.
NOTE: Be careful not to pinch wires.
MEMO: This snap band is not used.
8)
Insert the connector.
9)
Fix the SPF glass unit with screws, and install the table glass
and the glass holder right.
and the glass holder right.
10) Fix the right cabinet upper with three screws.
C. Main unit paper feed section dehumidifier
hearer installing procedures
1)
Remove the screws, and remove the rear plate.
MX-M1205 Dehumidifying heater kit 3 – 5
2)
Remove the harness and the screw, and remove the right cab-
inet rear upper.
inet rear upper.
3)
Remove two cabinet covers. Remove the screw, and remove
the right cabinet rear lower.
the right cabinet rear lower.
4)
Cut out the SW section of the heat-retention heater, and attach
the heater SW label to the frame as shown below.
the heater SW label to the frame as shown below.
(Be careful of the attachment direction of the heater SW label.)
5)
Attach the heat-retention heater switch.
* Attach so that the heater terminal is on the R side.
6)
Insert the connector into the heat-retention heater SW.
7)
Attach the PWB supporters (
✕5).
Heater SW label
Cut out this section for
installation of the
dehumidifier heater.
installation of the
dehumidifier heater.
For North America
MX-M1205 Dehumidifying heater kit 3 – 6
8)
Remove the snap band. (Preparation for insertion of the con-
nector into the WH PWB)
nector into the WH PWB)
9)
Insert the connector.
10) Connect the WH harness, and perform the line process.
11) Insert the connector, and fix it with the snap band.
12) Remove the screws, and remove the tandem tray.
13) Remove the screws, and remove the tray 3 and tray 4.
* The screws of the tray 3 should be removed when installing
the tray.
The above descriptions are based on the case where the
screws were not removed.
screws were not removed.
MX-M1205 Dehumidifying heater kit 3 – 7
14) Remove the screw, and remove the front covers of the cas-
sette 3 and cassette 4.
15) Attach the heater harness sheet to the heater mounting plate.
16) Attach the dehumidifier heater to the heater mounting plate
and fix it with M3
✕ 6S tight screw (✕ 1). Engage the pawls
(
✕ 2).
17) Fix the heater mounting plate assembly to the T heater cover
with M3
✕ 6S tight screws (✕ 2).
Fix the snap band at two positions, too.
18) Attach the heater cover sheet to the T heater cover.
* Repeat the procedures of 15) to 18) and make two sets.
19) Hang the heater mounting plate unit on the step screw of the
main unit frame, and fix them.
* Note that the screw on the upper side used to install the
heater mounting plate unit differs from that on the lower
side.
side.
Folding
reference
reference
L
o
ng
er
s
ide
Shorter side
Heater harness sheet
Edge reference
Pawls (
✕ 2)
M3
✕ 6S tight (✕ 1)
M3
✕ 6S tight 䋨✕ 2䋩
T heater cover
Heater cover sheet
Edge reference
Edge
reference
reference
Back side of T heater cover
Upper side
Lower side
Upper side
䌍䋴㬍䋸䌓 tight
Lower side
䌍䋳㬍䋶䌓
tight
tight
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man2) service manuals if exist.