DOWNLOAD Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ↓ Size: 31.08 MB | Pages: 127 in PDF or view online for FREE

MX-M1205  MX-EB15 (MIRRORING KIT)  24 – 1

MX-M1205

Service Manual

 

*1: Not use for this installation.

*2: Not use for this installation. (One of five screws)

Before installing the mirroring kit, fully understand the descriptions
below and careful follow the instructions.

When installing a mirroring kit newly, do not install a mirroring kit
which has been used. 

When a mirroring kit which has been used is installed in new instal-
lation of the mirroring kit, the mirroring kit HDD will overwrite the
machine HDD which has been original installed, deleting the user
data and causing a freeze of the machine.

“A mirroring kit which has been used” includes one which was only
installed and conducted.

When removing the HDD after installing the mirroring kit, be sure to
remove the both HDD’s. If only one HDD is removed and rein-
stalled, the data on the both HDD's data may be out of synchroni-
zation.

When removing the HDD, first disconnect the HDD SATA connec-
tor of the MFP PWB. This procedure brings the machine into the
state where the both HDD's are disconnected from the machine
simultaneously.

If a mirroring kit which has been used must be installed at any cost,
delete the mirroring information of the HDD before installing. (For
details, refer to “5. Deleting the HDD mirroring information” 
described later.)

MEMO: When the mirroring kit is installed to a machine which has
not been used, this procedure is not required. Backup of data with
a machine which has been used is made in order to provide against
a failure in automatic copy of data to the HDD of the kit.

1)

Use SIM56-2 or Web Page to backup the HDD data. 
(Device cloning data / Storage backup data)

2)

Use SIM56-3 or Web Page to backup the HDD data. 
(Document filing data)

3)

Use SIM56-4 or Web Page to backup the HDD data. 
(Jog log data (Reinstallation disable))

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation. 

1)

Remove the screw, and remove the rear cabinet.

1

Mirroring HDD unit

1

2

Screw  *2

5

3

Step screw

4

4

Damper

4

5

Wire saddle (small size) *1

2

6

Wire saddle (big size)

2

7

Earth plate *1

1

8

Core *1

2

9

SATA cable

2

10

Power cable

1

11

Communication cable

1

12

RAID PWB

1

13

Banding band

1

2

1

3

4

5

8

6

9

10

11

12

13

7

MX-M1205  MX-EB15 (MIRRORING KIT)  24 – 2

2)

Remove the harness.

3)

Remove the screw, and remove the plate.

Make a mark on both the mirroring HDD unit (Packed items No.1)
and the main HDD unit with a marker pen to indicate the use his-
tory.

1)

Attach the damper (Packed items No.4 x2) with the step screw
(Packed items No.3 x2).

2)

Attach the damper (Packed items No.4 x2) to the mirroring
HDD unit and install it to the MFP control unit with step screws
(Packed items No.3 x2).

MX-M1205  MX-EB15 (MIRRORING KIT)  24 – 3

1)

Remove the SATA cable and the power cable from the main
HDD unit.

MEMO: Open the clamp and unbind the SATA cable only.

2)

Attach the RAID PWB (Packed items No.12) with screws
(Packed items No.2 x4).

1)

Attach the wire saddle (big size) (Packed items No.6 x2) to the
frame as per the following picture.

2)

Connect the power cable (Packed items No.10) to the power
cable which was disconnected C-1). 
After connected, pass the power cable through the wire sad-
dles and connect to both the HDD.

MX-M1205  MX-EB15 (MIRRORING KIT)  24 – 4

3)

Connect the SATA cable (Packed items No.9).

MEMO: Bind up the cables as per the following picture.

NOTE: Be careful not to mistake the machine HDD with the

mirroring HDD. 
If the HDD should be erroneously connected, the con-
tents of the mirroring HDD would be written into the
machine HDD.

4)

Bind up the SATA cable which is unbinded in the step C-1) and
connect it.

NOTE: Twist the SATA cable two and half times and connect

it.

5)

Connect the communication cable (Packed items No.11).

Bind up the communication cable with banding band (Packed
items No. 13) after connection. (The following picture shows
bind up position.)

MEMO: Cut off excess part of the band with nippers.

NOTE: Check to confirm that the SATA connector is securely

connected.

1)

Turn on the main power switch and the operation panel power
switch.
Date copying from the standard HDD to the mirroring unit HDD
is started. It is called "Rebuilding.”

2)

Check to confirm that the machine is booted. 
It takes about three hours to complete rebuilding. Do not turn
off the power during rebuilding. When, however, the power is
turned off during rebuilding, turn on the power again, and
rebuilding will be continued. During rebuilding, a message is
displayed to indicate the operation. A job can be performed
during rebuilding, though the job speed may be reduced.

1)

Check to confirm that the mirroring kit active icon is displayed.

2)

Use SIM62-20 to check to confirm that the HDD status is OK/
REBUILDING.

3)

Perform copying and check to confirm that machine is normally
operating.

Mirroring kit installed

Mirroring kit/HDD trouble

Mirroring kit/Rebuilding