DOWNLOAD Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ↓ Size: 31.08 MB | Pages: 127 in PDF or view online for FREE

MX-M1205  MX-FD10 (FOLDING UNIT)  14 – 5

When the height of the paper folding unit is adjusted, execute the
caster roller height adjustment in the folder section according to the
following procedures.

1)

Open the front upper cover, pull out the folder section, remove
the screws, and remove the front cover of the folder section.

2)

Return the folder section to the inside of the machine. Loosen
the screws, and turn the adjuster bolt to adjust the height so
that the clearance between the caster roller and the floor is
about 1mm. After completion of the adjustment, tighten the
screw to fix.

1)

Connect the communication cables from the folding unit to the
finisher. Fix it with the screw (Packed items No.7).

2)

Remove the inlet cover of the finisher, and connect the power
relay cable (Packed items No.3).

1)

Connect the paper folding unit and the connection unit with the
shunt cable (Packed items No.8). Use the screw (Packed
items No.4).

[1]

[2]

 About 1mm

[1]

[2]

 

 

MX-M1205  MX-FN21/FN22 (FINISHER/SADDLE STITCH FINISHER)  15 – 1

MX-M1205

Service Manual

 

1)

Remove the fixing material, and remove the top case.

2)

Remove the bundled items from the top. 

3)

Remove the packing materials.

4)

One person holds the machine not to fall, and the other person
tilt the machine a little to remove the packing materials from
the lower section. Remove the vinyl cover.

5)

Put the base of the machine on the floor. (Use enough care not
to slip.)

6)

Tilt the machine slightly to the opposite side, and remove the
packing material on the opposite side. Remove the vinyl cover.

7)

Put the opposite side base of the machine on the floor.

8)

Remove the slopes and the fixing pins from the pallet.

9)

Fix the slopes to the pallet with the fixing pins.

MX-M1205  MX-FN21/FN22 (FINISHER/SADDLE STITCH FINISHER)  15 – 2

10) Move the finisher from the pallet to the floor slowly.

1)

Remove the fixing tape and the fixing bracket from the finisher.

2)

Remove the screw, and remove the four fixing members of the
lift tray rail section.

1

Latch receiver

2

2

Positioning pin

1

3

Shunt cable unit

1

4

Wire saddle

1

5

Spacer

1

6

Staple unit staple case

1

7

Spring + small bind screw with flat washer (M4)

1

2

1

4

5

3

7

6

9

8

11

10

13

14

15

12

8

Screw (RS tight, M4 x 8)

9

9

Latch cover

1

10

Screw (Bind, M4 x 6)

2

11

Power cord

1

12

Staple position label (For scanner)

1

13

Staple position label (For DSPF)

1

14

Punch position label (For scanner)

1

15

Punch position label (For DSPF)

1

1

Latch receiver

2

2

Positioning pin

1

3

Shunt cable unit

1

4

Wire saddle

1

5

Spacer

1

6

Staple unit staple case

1

7

Power cord

1

8

Screw (RS tight, M4 x 8)

9

9

Bookbinding tray

1

10

Saddle stitcher unit accessory caster

1

11

Screw (with spring washer)

2

12

Staple position label (For scanner)

1

13

Staple position label (For DSPF)

1

14

Punch position label (For scanner)

1

15

Punch position label (For DSPF)

1

2

1

4

5

3

7

6

8

9

10

11

13

14

15

12

MX-M1205  MX-FN21/FN22 (FINISHER/SADDLE STITCH FINISHER)  15 – 3

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Open the front cover of the finisher. Insert the staple unit staple
case into the staple unit until it clicks.

1)

Attach the spacer to the inside of [A] at the groove in the right
side of the upper cover of the finisher. Since the groove is
shorter than the spacer, put the spacer in parallel with the top
line where there is no groove.

Cushion attachment 
position

⾍ઃၮḰ

Reference of cushion on.
(Upper cabinet side tier)

Reference of cushion on.
(Upper cabinet lower edge)

Cushion attachment 
position

Reference of cushion on.
(Upper cabinet side tier)

Reference of cushion on.
(Upper cabinet lower edge)

[A]

[A]