Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ▷ View online
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 22
O. Necessary procedures before moving the
machine
1) If the following options are installed, remove all of them from
the machine.
• Large capacity tray
• Inserter
• Finisher
• High capacity stacker
• Curl correction unit
• Relay unit
• Paper feed system option
• Large capacity tray
• Inserter
• Finisher
• High capacity stacker
• Curl correction unit
• Relay unit
• Paper feed system option
2) Remove the following consumable parts from the machine.
• Paper
• Toner cartridge
• Development cartridge
• Toner cartridge
• Development cartridge
3) Lock the following sections.
• Scanner (Optical section)
• Paper cassette lift plate
• Paper cassette lift plate
4) Attach the protection material to the position shown below.
• Use the "packing material for fixing the separation pawls"
which was removed when unpacking.
NOTE: Since the hard disk drive is built in the machine, refrain
from vibrations or shocks to the machine when in transit.
MX-M1205 Dehumidifying heater kit 3 – 1
MX-M1205
Service Manual
[3] Dehumidifying heater kit
1. Parts list
No.
Parts name
Parts code
Quantity
Remarks
1
Heater kit HER200
DKIT-0406FCZZ
1
2
WH PWB
QPWBF1569FCE2
1
3
Supporter SPLSN-6
LSUPP0118FCPZ
5
4
WH harness
DHAI-4075HCPZ
1
5
Heater SW
QSW-C9294QCZZ
1
6
Heater SW label Pa EX
TLABZ5256FCZZ
1
7
SCN dehumidifier heater 230V
RHETP0148FCPZ
1
For SCN heater mounting
8
Snap band
LBNDJ0071FCZZ
2
For SCN heater mounting
9
Screw (M3 x 4cap, black)
LX-BZ0324FCPZ
2
For SCN heater mounting
10
Edge saddle, black
LBSHC0161FCZZ
1
For SCN heater mounting
11
Main unit cassette heater (240)V
RHETP0150FCPZ
2
Formain unit heater mounting
12
Heater mounting plate
LPLTM6089FCZZ
2
Formain unit heater mounting
13
T heater cover
PCOVP1654FCZ2
2
Formain unit heater mounting
14
Heater cover sheet
PSHEZ5012FCZZ
2
Formain unit heater mounting
15
Heater harness sheet
PSHEZ5135FCZZ
2
Formain unit heater mounting
16
Screw (M3 x 6S)
XHBS730P06000
7
Formain unit heater mounting
(For dehumidifier heater unit: x6, For cassette 4 heater: x1)
(For dehumidifier heater unit: x6, For cassette 4 heater: x1)
17
High temperature caution label
TLABZ5217FCZZ
1
Formain unit heater mounting
18
High temperature caution mark label
TLABZ4900FCZZ
1
Formain unit heater mounting
19
Screw (M4 x 8S)
XHBS740P08000
1
For cassette 3 heater mounting
Kit name
Kit part code
Parts name
Part code
Q'ty
LCC (A4) heater kit
DKIT-0437FC11 (200V series)
DKIT-0437FC12 (200V series)
DKIT-0437FC12 (200V series)
Heater harness (Ex200V North America)
DHAI-5199FCPZ
1
Heater harness (Ex200V Europe)
DHAI-5200FCPZ
Snap band
LBNDJ0043FCP1
1
AC cord fixer
LFIX-0016FCZZ
1
Connector cover A
PCOVP2149FCZZ
1
Connector cover B
PCOVP2150FCZZ
1
Heater (200V series)
RHETP0121FCZZ
1
Screw (M4 x 8K)
XBPS740P08K00
1
Screw (M3 x 4)
XHBS730P04000
1
Screw for EL connector
LX-BZ1119FCZZ
1
Screw (M4 x 28K)
XBPS740P28KS0
2
Screw (M3 x 20)
XBBS730P20000
3
Screw (M4 x 8)
XHBS740P08000
1
Nut (M3 = 2.4)
XNES730-24000
3
LCC (A3) heater kit
DKIT-0439FCZZ (200V series)
DKIT-0440FCZZ (200V series)
DKIT-0440FCZZ (200V series)
Heater harness A3 (Ex200V North America)
DHAI-5203FCPZ
1
Heater harness A3 (Ex200V Europe)
DHAI-5204FCPZ
Snap band
LBNDJ0043FCP1
1
AC cord fixer
LFIX-0016FCZZ
1
Connector cover A
PCOVP2149FCZZ
1
Connector cover B
PCOVP2150FCZZ
1
Heater (200V series)
RHETP0121FCZZ
1
Screw (M4 x 8K)
XBPS740P08K00
1
Screw (M3 x 4)
XHBS730P04000
1
Screw for EL connector
LX-BZ1119FCZZ
1
Screw (M4 x 28K)
XBPS740P28KS0
2
Screw (M3 x 20)
XBBS730P20000
3
Screw (M4 x 8)
XHBS740P08000
1
Nut (M3 = 2.4)
XNES730-24000
3
Heater cover
PCOVP1942FCZZ
1
Heater sheet
PSHEZ5482FCZZ
1
Screw (M4 x 8 Round-tipped S-tight)
LX-BZ0941FCPZ
2
2
: ‘17/Apr.
2
MX-M1205 Dehumidifying heater kit 3 – 2
LCT heater kit
DKIT-0442FCZZ (120V series)
DKIT-0442FC11 (200V series)
DKIT-0442FC11 (200V series)
LCT heater (120V series)
RHETP0145FCZZ
2
LCT heater (200V series)
RHETP0121FCZZ
LCT heater mount plate
LPLTM8436FCZZ
2
Mini clamp
LHLDW1009ACZZ
4
Edge wire saddle
LHLDW1503FCZZ
6
Screw (M3x4 S-tight)
XHBS730P04000
16
Desk heater (120V series)
RHETP0144FCZZ
3
Desk heater (200V series)
RHETP0139FCZZ
Desk heater mount plate
LPLTM6021FCZZ
3
Heater heat sink
PRDAR0087FCZZ
3
Mini clamp
0EUHLD0214C//
9
Screw (M3x6 S-tight)
XHBS730P06000
6
Screw (M4x8 S-tight)
XHBS740P08000
2
Step screw
LX-BZ0714FCPZ
2
High temperature warning label
TLABZ4900FCZZ
2
Dehumidifier heater switch
QSW-C9294QCZZ
1
LCT WH SW harness
DHAI-5131FCPZ
1
LCT heater harness 1 (120V series)
DHAI-5143FCPZ
1
LCT heater harness 1 (200V series)
DHAI-5251FCPZ
LCT heater harness 2 (120V series)
DHAI-5144FCPZ
1
LCT heater harness 2 (200V series)
DHAI-5252FCPZ
Heater SW label Pa EX
TLABZ5256FCZZ
1
Kit name
Kit part code
Parts name
Part code
Q'ty
MX-M1205 Dehumidifying heater kit 3 – 3
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Turn OFF the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cover, turn OFF the main power switch.
3)
Disconnect the power cord of the main unit from the power out-
let.
let.
B. Scanner unit dehumidifier heater installing
procedures
1)
Remove three screws from the right cabinet upper.
2)
Remove the screw, and remove the glass holder right, the SPF
glass unit, and the table glass.
glass unit, and the table glass.
MEMO: Shift the lamp unit completely to the right end of the
optical frame.
optical frame.
3)
Remove the screw (a), and remove the dust-proof cover LB.
NOTE: When removing the dust-proof cover LB, be careful of
two pawls.
4)
Install the dehumidifier heater to the optical frame with two
black screws (M3 x 4), and fit it with the snap band (included in
the package).
black screws (M3 x 4), and fit it with the snap band (included in
the package).
NOTE: When installing, be careful in the direction of the snap
band.
NOTE: Remove slack from the harness between the dehumid-
ifier heater and the snap band.
5)
Install the edge saddle, and through the harness of the dehu-
midifier heater.
midifier heater.
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man2) service manuals if exist.