Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ▷ View online
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 18
2) Install the toner cartridge (a).
3) Install the toner tray (a).
J. Tray setup
(1) Setting of paper size and paper type
Change the tray setting in the "system setting" mode. Some items
require administrator authority for display. The paper setting (to A4/
recycle) procedure for tray 3 is as follows.
However, if the size of tray 1 has been switched to B5, execute SIM
26-2, and set the paper size.
1) Press the [SETTINGS] key on the operation panel.
2) Press the [SYSTEM SETTINGS] key.
3) Touch the [Paper Tray Settings] key.
4) Touch the [Tray 3] key.
5) Select "recycled" on the selection box of the "Type". Select
require administrator authority for display. The paper setting (to A4/
recycle) procedure for tray 3 is as follows.
However, if the size of tray 1 has been switched to B5, execute SIM
26-2, and set the paper size.
1) Press the [SETTINGS] key on the operation panel.
2) Press the [SYSTEM SETTINGS] key.
3) Touch the [Paper Tray Settings] key.
4) Touch the [Tray 3] key.
5) Select "recycled" on the selection box of the "Type". Select
"A4" on the selection box of the "Size". Touch the [Submit] key.
(2) Tray size setup
a. Inch series tray 1, tray 2 (LT to A4)
1) Pull out the tray 1/2 (a).
1) Pull out the tray 1/2 (a).
2)
Push down the paper feed base plate (a) gently, hold the
hooks and remove A4 size regulation plate (b).
hooks and remove A4 size regulation plate (b).
3)
Fit the A4 size regulation plate (a) to A4 size, and attach it.
* Be careful to align regulation plates properly into base.
* Be careful to align regulation plates properly into base.
a
a
a
a
a
b
b
b
b
a
a
a
a
b
b
b
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 19
4) Close the tray 1/2 (a).
b. Tray 3, tray 4
1) Gently pull out trays 3 and 4 (a) until each tray stops.
1) Gently pull out trays 3 and 4 (a) until each tray stops.
2) Adjust the guide plates (a) and (b) by squeezing their lock
levers and sliding them to match the vertical and horizontal
dimensions of the paper to be loaded.
Squeeze the lock knob on guide plate (a), (b) and slide to the
desired paper size.
For a non-standard paper size, after sliding guide plate (b) to
the desired size, press the lock button (c).
* If slid to a standard paper size, guide plate (b) will lock auto-
dimensions of the paper to be loaded.
Squeeze the lock knob on guide plate (a), (b) and slide to the
desired paper size.
For a non-standard paper size, after sliding guide plate (b) to
the desired size, press the lock button (c).
* If slid to a standard paper size, guide plate (b) will lock auto-
matically.
K. Specifications setup
Used to set the specifications with SIM26 according to the cus-
tomer's request.
tomer's request.
To customize the following items after completion of the destination
setup, change the set values.
setup, change the set values.
L. Image quality check
Be sure to check the following items related to image quality. For
details of the adjustment and checking procedures, refer to the “[5]
ADJUSTMENT” on the Service Manual.
Check that the following items are within specification. If not, carry
out the adjustment.
details of the adjustment and checking procedures, refer to the “[5]
ADJUSTMENT” on the Service Manual.
Check that the following items are within specification. If not, carry
out the adjustment.
NOTE: When installing the copier, be sure to carry out the copy
gray balance and the printer gray balance.
(1) Image loss, void area (see ADJ 9)
(2) Copy gray balance (11-A / Auto adjustment)
(2) Copy gray balance (11-A / Auto adjustment)
1)
Enter the SIM 46-74 mode.
2)
Press [EXECUTE] button.
The high density process control is performed, and the copy
gray patch image (adjustment pattern) is printed out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
The high density process control is performed, and the copy
gray patch image (adjustment pattern) is printed out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
a
B
a
b
c
SIM No
Content
26
6
Used to set the destination.
SIM No
Content
26
2
Paper size setting of the Tray1/LCC.
3
Used to set the auditor specification mode.
5
Used to set the number (1 or 2) of count of paper
(A3 or WLT or 8K) that passes.
1:1pc 2:2pcs
* Targets: Total counter, maintenance counter,
(A3 or WLT or 8K) that passes.
1:1pc 2:2pcs
* Targets: Total counter, maintenance counter,
developer counter.
18
Used to set YES/NO of the toner save mode (Only
in UK and Japan versions)
* Carry out the setting by the user's program
in UK and Japan versions)
* Carry out the setting by the user's program
except the UK version.
1:accept 2:inhibit
52
Used to set whether non-printed paper (insertion
paper, cover paper) is counted up or not.
1:YES 2:NO
paper, cover paper) is counted up or not.
1:YES 2:NO
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 20
3) Set the gray patch image (adjustment pattern) paper printed in
procedure 2) on the document table.
Set the gray patch image (adjustment pattern) printed in the
procedure 2) on the document table.
Place the gray patch image so that the fine lines are on the left
side.
At that time, place 5 sheets of white paper on the printed gray
patch image (adjustment pattern).
Set the gray patch image (adjustment pattern) printed in the
procedure 2) on the document table.
Place the gray patch image so that the fine lines are on the left
side.
At that time, place 5 sheets of white paper on the printed gray
patch image (adjustment pattern).
4) Press [FACTORY] button, then press [EXECUTE] button.
The copy density and gradation adjustment is performed auto-
matically, and the adjustment pattern is printed.
If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.
matically, and the adjustment pattern is printed.
If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.
5)
Press [EXECUTE] key.
The printer gray patch image (adjustment pattern) is printed
out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
The printer gray patch image (adjustment pattern) is printed
out.
(A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.)
6)
Set the gray patch image (adjustment pattern) printed in the
procedure 5) on the document table.
Set the gray patch image (adjustment pattern) printed in the
procedure 2) on the document table.
Place the gray patch image so that the fine lines are on the left
side.
At that time, place 5 sheets of white paper on the printed gray
patch image (adjustment pattern).
procedure 5) on the document table.
Set the gray patch image (adjustment pattern) printed in the
procedure 2) on the document table.
Place the gray patch image so that the fine lines are on the left
side.
At that time, place 5 sheets of white paper on the printed gray
patch image (adjustment pattern).
Q
O P
N
M
L
K
J
I
H
G
F
E
D
C
B
A
High
density
density
Low
density
density
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 21
7) Select [FACTORY] target, and press [EXECUTE] key.
When the gray balance is customized with the manual gray
balance adjustment (SIM 67-25) according to the user's
request and the gray balance is registered as the service tar-
get with SIM 67-27, if the gray balance is adjusted to that gray
balance, select the [SERVICE] target.
The printer gray balance adjustment (step 1) is automatically
performed and the gray balance check patch image is printed
out.
If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.
balance adjustment (SIM 67-25) according to the user's
request and the gray balance is registered as the service tar-
get with SIM 67-27, if the gray balance is adjusted to that gray
balance, select the [SERVICE] target.
The printer gray balance adjustment (step 1) is automatically
performed and the gray balance check patch image is printed
out.
If there is any streak or unclear print on the printed check pat-
tern, check the print engine for any problems.
8) The initial setting menu of the halftone image correction is dis-
played.
Press [OK] key.
The initial setting of the halftone image correction is per-
formed.
Press [OK] key.
The initial setting of the halftone image correction is per-
formed.
9) Wait until [EXECUTE] key is displayed.
When it is displayed, press it.
The halftone image correction is performed.
The halftone image correction is performed.
10) When "COMPLETED THIS PROCEDURE" is displayed, the
adjustment operation is completed.
Cancel SIM46-74.
Cancel SIM46-74.
NOTE: The adjustment result becomes valid only when the
both adjustments in the copy mode and in the printer
mode are completed.
For example, if the copy gray balance adjustment
(automatic adjustment) is performed and the simula-
tion is canceled, the adjustment result is invalid.
mode are completed.
For example, if the copy gray balance adjustment
(automatic adjustment) is performed and the simula-
tion is canceled, the adjustment result is invalid.
11) Check the copy gray balance and density.
(Refer to the item of the copy gray balance and density check.)
When the gray balance and the density are unsatisfactory after
the automatic adjustment by selecting the factory target in pro-
cedure 4), execute the manual gray balance adjustment
(ADJ11C (2)).
Also when the service target is selected in procedure 4) to exe-
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11C (2)).
When the gray balance and the density are unsatisfactory after
the automatic adjustment by selecting the factory target in pro-
cedure 4), execute the manual gray balance adjustment
(ADJ11C (2)).
Also when the service target is selected in procedure 4) to exe-
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11C (2)).
12) Check the printer gray balance and density.
(Refer to the item of the printer gray balance and density
check.)
If a satisfactory result on the gray balance and the density is
not obtained with the automatic adjustment, execute the man-
ual adjustment (SIM 67-25) (ADJ 11E (2)).
Also when the service target is selected in procedure 7) to exe-
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11E (2)).
If the gray balance or density is not in the satisfactory level
even after execution of the automatic and manual adjustments,
there may be another cause.
Troubleshoot the cause, repair or perform necessary works,
and repeat the adjustment from the beginning.
check.)
If a satisfactory result on the gray balance and the density is
not obtained with the automatic adjustment, execute the man-
ual adjustment (SIM 67-25) (ADJ 11E (2)).
Also when the service target is selected in procedure 7) to exe-
cute the automatic adjustment and a satisfactory result is not
obtained, perform the manual gray balance adjustment (ADJ
11E (2)).
If the gray balance or density is not in the satisfactory level
even after execution of the automatic and manual adjustments,
there may be another cause.
Troubleshoot the cause, repair or perform necessary works,
and repeat the adjustment from the beginning.
M. Function and operation check
Check that the following operations are normal.
N. Setup and adjustment data recording
Print the various setup data and the adjustment data (list) with
SIM22-6 and keep the data.
• In case of a memory problems, if the data is not kept, all the
SIM22-6 and keep the data.
• In case of a memory problems, if the data is not kept, all the
adjustments must be made again.
• If the data is kept, the setup values and the adjustment values
can be entered without adjustments, shortening the servicing
time.
time.
Q
O P
N
M
L
K
J
I
H
G
F
E
D
C
B
A
Bk
1) The max. density section is not blurred.
2) Patch C or D is very slightly copied.
3)
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
The patch density is changed gradually.
High density
Low density
Check item list
Equipped condition
Key-in (operation panel)
Display (operation panel)
Paper feed
operation
Display (operation panel)
Paper feed
operation
Hand feed
Paper tray
Paper tray
Paper size detection
Originals size
detection
Originals size
detection
Original table
mode
DSPF mode
mode
DSPF mode
DSPF
operation/
duplex
operation
operation/
duplex
operation
S-S mode
D-S mode
S-D mode
D-D mode
D-S mode
S-D mode
D-D mode
Bookbinding operation
When the finisher is installed
Stapling operation
When the finisher is installed
Grouping operation
When the finisher is installed
Sorting operation
When the finisher is installed
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man2) service manuals if exist.