Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ▷ View online
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 14
(1) Turn ON the power of the main unit
1) Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
power switch.
(2) Keyboard input check
1) Touch [E-Mail] on the touch panel.
2) Touch the input column of the address.
3) Input the address with the keyboard, and check the input result
2) Touch the input column of the address.
3) Input the address with the keyboard, and check the input result
on the touch panel.
(3) USB operation check
1) Insert the USB memory into the USB connector of the opera-
tion panel.
2) Check to confirm that the recognition mark of the USB memory
is displayed on the operation panel.
E. Fusing heat roller pressure
1) Open the front cover (a), and pull out the intermediate frame
(b).
2) Remove the screw (a), and remove the cover (b).
3) Insert a screwdriver into the pressure release shaft (a) to apply
pressure.
* When the pressure is released, the arrow on the pressure
* When the pressure is released, the arrow on the pressure
release shaft faces diagonally (b). When the pressure is
applied, the arrow faces upward (c).
applied, the arrow faces upward (c).
NOTE: If the machine is left unused for one month or more, the
heat roller rubber may be deformed. In such a case,
release the pressure.
release the pressure.
F. Developer supply
1)
Open the front cover (a), and pull out the intermediate frame
(b).
(b).
2)
Remove the screw (a), and remove the cover (b).
3)
Remove the blue screw, and remove the plate (b).
a
b
a
b
a
c
b
a
b
a
b
a
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 15
4) Slide the developing unit (a) to the right, and pull it out until the
grip (b) can be held.
5) Hold the handle (a) of the developing unit, and lift it up to
remove completely.
* When placing the developing unit down, rotate the stabilizing
* When placing the developing unit down, rotate the stabilizing
leg and place the developing unit down with the leg
extended.
extended.
6) Remove the connector (a), the screw (b), and the cover (c).
* Be careful not to smear the pin of the connector (a) with
toner.
7)
Remove the screw (a), and remove the guide (b).
8)
Remove the cover (a).
9)
While rotating the coupling (a), supply developer (b).
10) Attach the cover (a).
a
b
b
a
a
b
c
a
a
b
a
a
b
a
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 16
11) Attach the guide (a), and secure it with the screw (b).
12) Attach the cover (a), and secure it with the screw (b). Connect
the connector (c).
* Check to confirm that the pin of the connector (c) is not
* Check to confirm that the pin of the connector (c) is not
smeared with toner.
13) Rotate the stabilizing leg (a) under the developing unit
and install the developing unit (b).
* When inserting a developing unit with SIM25-2 not exe-
* When inserting a developing unit with SIM25-2 not exe-
cuted, be sure to check that the power is turned OFF.
14) Slide the developing unit (a) to the left, and lock it.
15) Attach the plate (a), and secure it with the screw (b).
16) Attach the cover (a), and secure it with the screw (b).
b
b
a
c
b
a
a
b
a
b
b
b
a
b
a
b
MX-M1205 MX-M1055/M1205 (MAIN UNIT) 2 – 17
17) Insert the toner tray (a), and close the front cover (b).
G. Toner collection container check
1) Open the front cover (a).
2) Check to confirm that toner collection container (a) is securely
installed.
H. Toner density reference control level setting
1)
Connect the power cord of the main unit to the power
outlet.
outlet.
2)
Open the front cover, and turn ON the main power switch.
3)
Turn ON the power switch on the operation panel.
4)
Open the front cover, and remove the toner cartridge. Then
enter the input of SIM25-2.
enter the input of SIM25-2.
5)
After entering the simulation, close the front cover (a).
6)
Press [EXECUTE] button, and the simulation is executed.
After stirring toner, the toner density control sensor values are
sampled to get the average value of the sensor detection level,
which is set (saved) as the reference toner density control
value.
After stirring toner, the toner density control sensor values are
sampled to get the average value of the sensor detection level,
which is set (saved) as the reference toner density control
value.
7)
After completion of the reference toner density control value
setting, [EXECUTE] key returns to the normal display, showing
completion of the setting operation.
setting, [EXECUTE] key returns to the normal display, showing
completion of the setting operation.
I. Toner cartridge installation
1)
Pull out the toner tray (a).
b
a
a
a
a
a
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man2) service manuals if exist.