Sharp MX-M1055 / MX-M1205 (serv.man2) Service Manual ▷ View online
MX-M1205 Dehumidifying heater kit 3 – 12
2)
While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.
paper feed tray.
3)
Remove the screws at the back side of the paper feed tray,
and remove the binding band and the earth wire. Disconnect
the connector.
and remove the binding band and the earth wire. Disconnect
the connector.
4)
Remove the screws at the both sides of the paper feed tray,
and remove the paper feed tray from the slide rail.
and remove the paper feed tray from the slide rail.
(4)
Attach the LCT heater unit and desk heater unit
1)
Attach the mini clamp and step screw to the frame.
Put the LCT heater unit on the step screw and fix it with the
tight screw (M4 x 8 S-tight).
Put the LCT heater unit on the step screw and fix it with the
tight screw (M4 x 8 S-tight).
Pass the LCT heater harness through the mini clamp.
2)
Affix the high temperature warning label onto the frame.
1
2
2
1
1
3
2
4
1
1
1
2
1
4
3
1
2
4
3
1
2
5
Edge
Ref
erence
0mm
0.5mm
Edge
Reference
0mm
0.5mm
MX-M1205 Dehumidifying heater kit 3 – 13
3)
Attach the mini clamp to the frame. Attach the desk heater unit,
and fix by the screw (M3 x 6 S-tight). Pass the desk heater har-
ness through the mini clamp.
and fix by the screw (M3 x 6 S-tight). Pass the desk heater har-
ness through the mini clamp.
(5)
Remove the rear cabinet and left rear cabinet
1)
Disconnect the power cord. Loosen the screws at the bottom
ends. Remove the screw, and remove the rear cabinet.
ends. Remove the screw, and remove the rear cabinet.
2)
Remove the screw, and remove the left rear cabinet.
(6)
Connect the harness
1)
Attach the mini clamp and edge wire saddle to the frame.
2)
Attach the dehumidifier heater switch to the frame. Connect
the LCT WH SW harness.
the LCT WH SW harness.
NOTE: Attach the switch to the frame; the switch terminal
must be in front frame direction.
3
1
1
1
2
3
2
3
2
4
1
2
3
3
3
3
4
1
1
2
1
Connector
Connector
Dehumidifier
heater switch
heater switch
Connector
Front side
MX-M1205 Dehumidifying heater kit 3 – 14
3)
Connect the LCT heater harness 1. Pass the LCT heater har-
ness 1 through the wire saddle and mini clamp, and fix the
snap band.
ness 1 through the wire saddle and mini clamp, and fix the
snap band.
4)
Pass the LCT heater harness 1 through the edge wire saddle,
and fix the snap band.
and fix the snap band.
5)
Fix the snap band, and connect the connector.
6)
Connect the LCT heater harness 2.
7)
Connect the connector, and fix the snap band.
8)
Connect the connector, and fix the snap band.
Connector
Wire saddle
Snap band
Mini clamp
Snap band
Snap band
Snap band
Snap band
Edge wire saddl
Snap band
Connector
Connector
Connector
Connector
Snap band
Snap band
Connector
Snap band
MX-M1205 Dehumidifying heater kit 3 – 15
(7)
Attach the left rear cabinet and rear cabinet
1)
Cut the switch part of the left rear cabinet.
2)
Attach the left rear cabinet, and fix by the screw.
3)
Attach the rear cabinet, and fix by the screw. Tighten the screw
at the bottom ends. Connect the power cord.
at the bottom ends. Connect the power cord.
(8)
Attach the paper feed tray
1)
Attach the paper feed tray to the slide rail, and fix by the screw.
2)
Connect the connector into the back side of the paper feed
tray. Attach the earth wire and the binding band, and fix by the
screw.
tray. Attach the earth wire and the binding band, and fix by the
screw.
2
2
1
2
4
3
2
2
2
2
1
2
2
2
1
2
4
4
2
3
1
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man2) service manuals if exist.