Sharp MX-BMX1 (serv.man9) User Manual / Operation Manual ▷ View online
1
25
Plug the Booklet Maker powercord into the wall
outlet.
Cover Feeder (optional), Trimmer (optional) and
Book Folder (optional) are powered from the
Booklet Maker.
Open the Top cover (1).
Set main power switch (2) on Booklet Maker to ON
position.
Note
The main power switch also controls Cover Feeder
(optional), Trimmer (optional) and Book Folder
(optional).
Close the Top cover.
Turning On / Off the Main Power
Booklet Maker, Cover Feeder, Trimmer and Book Folder
2
1
1
26
The staple cartridges, containing approximately 5000
staples per cartridge. Cartridge may be removed either
for renewal or for jam clearance.
Raise the handle (C) on the staple cartridge locking
lever.
Remove the staple cartridge from the stapler head
by sliding it away from the stapler head.
Check staples, Staple cartridge and stapler head
Open the top cover.
Remove the set of paper.
Disconnect the staple indication lead (A) from the
socket.
Hold the stapler head in place, press the release
latch (B) to release the rear end of the stapler head
and lift up this end.
Lift out the head, allowing it to rotate around the
front end. The stapler assembly is spring loaded
and will follow the rotation of the stapler.
Removing stapler head
A
B
C
Removing staple cartridge
1
2
Look inside stapler head for jammed staples in the area
of the staple actuator. Remove staples if any.
Position the stapler head on the edge of a firm surface
(for example the top of a table).
While securely holding the head, actuate the Stapler
While securely holding the head, actuate the Stapler
up and down through full travel. Perform this operation
without staple cartridge
Renewing or reinstalling the staple cartridge, pull 25
Renewing or reinstalling the staple cartridge, pull 25
mm (1 inch) of staples out of the cartridge and tear the
staples downward starting at one side pulling away
from you. The staple tear line is indicated by an arrow
on the side of the cartridge.
Insert the cartridge into the stapler head with the end
of the staples facing toward the head of the stapler
mechanism. Push it firmly ahead.
Hold the staple cartridge firmly in place and push down
Hold the staple cartridge firmly in place and push down
the cartridge locking lever.
IMPORTANT
Keep holding (pushing) the staple cartridge into place
while pushing down the cartridge locking lever.
While securely holding the head, actuate the Stapler up
and down through full travel. Perform this operation with
staple cartridge. Repeat this a few times to ensure that
the staples are ejected at each down movement.
Reinstall the stapler head by inserting the pin at the top of
Reinstall the stapler head by inserting the pin at the top of
the stapler head into the stapler retraction swing arm (D).
While rotating the stapler head, insert the pin located
at the rear end of the stapler head into the slots in the
frame of the stapler head assembly. Press down the
rear end of the stapler head until the release lever snaps
into place, locking the stapler head in position.
Press down the front end of the stapler head until it
Press down the front end of the stapler head until it
snaps in position under the frame assembly.
Reconnect the staple indication lead (A), see previous
Reconnect the staple indication lead (A), see previous
page.
Close the top cover and press the [Esc] button. The
booklet maker will automatically go to Ready mode. If
not and/or error message persists, hand feed a four
sheet set of paper. The booklet maker will automatically
cycle and advance staples until both stapler heads are
driving staples. The booklet maker will automatically go
to Ready mode.
Installing stapler head, staple cartridge / clearing staple jam
D
1
28
Emptying the trim bin
Remove the trim bin by lifting it and pulling it out.
trim bin, no Book Folder installed
trim bin, with Book Folder installed
Click on the first or last page to see other MX-BMX1 (serv.man9) service manuals if exist.