Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) Service Manual ▷ View online
MX-6070V MX-FN31 (SADDLE STITCH FINISHER) 15 – 5
5)
When adjusting the skew, make adjustment at 2casters shown in
the picture.
the picture.
Adjust the skew of the adjusting nut of the caster by turning it in
the direction of the arrows as shown.
the direction of the arrows as shown.
*For skewing the finisher to the right side: Turn the nut in [A] direc-
tion.
tion.
*For skewing the finisher to the left side: Turn the nut in [B] direc-
tion.
tion.
6)
After the adjustment, return the wrench to the original position.
G. Fixation of the lock slide plate
1)
Fix the lock slide plate with the screw (x1) (M3x6 S Tight).
Close the front cover of the finisher.
H. Connection of the harness
1)
Attach the connector of the finisher and fix it with the screw.
I.
Placing of the staple position label
1)
Place the staple position label (for scanner)
2)
Place the staple position label (for RSPF)
J. Power-ON of the main unit
1)
Insert the power plug into the socket, and turn ON the main power
switch and the power switch of the operation panel.
switch and the power switch of the operation panel.
[B]
[A]
[A]
[B]
Screw
M3×6 S-tight
Ĭ
ĭ
)LWZLWKWKHFRUQHU5
)LWZLWKWKHFRUQHU5
/DEHODWWDFKPHQWUHIHUHQFH
&RUQHURIWKHXSSHU
FDELQHWERWWRP
MX-6070V MX-PN16B/C/D (PUNCH MODULE) 16 – 1
MX-6070V
Service Manual
[16] MX-PN16B/C/D (PUNCH MODULE)
1. Unpacking
A. Packed items check
B. Packed items check
1)
Open the outer box and remove the punch unit and packed items.
2)
Remove all the cushioning materials and tapes from the punch
unit.
unit.
3)
Remove 3 screws to remove 2pcs of attaching material.
NOTE: Save the 3 screws removed for installation of the punch unit.
2. Installation
NOTE: Be sure to install the punch unit before installing the finisher to
the main unit. In case of installing the punch unit afterward,
remove the finisher from the main unit once.
remove the finisher from the main unit once.
NOTE: Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the
power outlet.
power outlet.
Make sure that the data lamp on the operation panel does not
light up or blink prior to the installation.
light up or blink prior to the installation.
A. Removal of rear cover and top cover
1)
Remove filament tapes from the packing materials.
2)
When the finisher is connected to the main unit, disconnect the
interface cable and remove the finisher.
interface cable and remove the finisher.
3)
Remove two screws fastened to rear cover of the finisher.
4)
Incline upper part of the rear cover and remove the rear cover
while lifting the pawls of the rear cover.
while lifting the pawls of the rear cover.
No.
Name
Quantity
1
Punch unit
1
2
Punch waste full sensor unit
1
3
Harness
1
4
Punch waste Tray
1
5
Positioning guide
1
6
Punch position label (for RSPF/DSPF)
1
7
Punch position label (for scanner)
1
8
Punch cushion A (Resin board)
1
9
Punch cushion B (PORON- Sponge)
1
10
Screw (S tight screw, M3x8)
1
1
2
3
4
5
6
7
8
9
10
Remove two screws.
Position of the pawls of the rear cover
and insertion slot on the finisher unit
and insertion slot on the finisher unit
Rear cover
Finisher unit
MX-6070V MX-PN16B/C/D (PUNCH MODULE) 16 – 2
5)
Open front cover of the finisher.
6)
Remove 4 screws to remove a fulcrum for top cover.
7)
Incline a lever to the right and open top cover.
8)
Slide the top cover toward the direction of an arrow 1 and remove
the top cover toward the direction of an arrow 2.
the top cover toward the direction of an arrow 2.
B. Removal of dummy unit
1)
Disconnect the connector on rear side.
2)
Remove a screw, slide toward front and uplift the guide. The hook
will be removed; remove the guide from rear side.
will be removed; remove the guide from rear side.
3)
Cut 5 sections of insertion slot for punch waste tray using a nipper
and remove.
and remove.
Top cover
Fulcrum
Screws
ĭ
Į
Ĭ
MX-6070V MX-PN16B/C/D (PUNCH MODULE) 16 – 3
C. Attachment of positioning guide
1)
Attach right edge of positioning guide (Packed item No.5) in refer-
ence to the center of the scale. Use a screw (M3x6) removed in
the step 3) in “Unpacking”.
ence to the center of the scale. Use a screw (M3x6) removed in
the step 3) in “Unpacking”.
D. Installation of punch unit
1)
Attach Punch cushion B (Packed item No. 9) along the reference
face on Punch inner cover for Punch unit.
face on Punch inner cover for Punch unit.
2)
Install the punch unit (Packed item No.1) from rear side of the fin-
isher by letting it through under the top cover.
isher by letting it through under the top cover.
3)
Make sure there is no space between base of the punch unit and
a frame.
a frame.
4)
Fix the punch unit with a screw. Use a screw (M3x6) removed in
the step 3) in “Unpacking”.
the step 3) in “Unpacking”.
5)
Attach the fulcrum for top cover again using 4 screws.
E. Attachment of punch waste full sensor unit
1)
Remove filament tapes from the packing materials.
6FDOH
Reference face
Reference face
Punch inner cover
Top cover
Fulcrum
Screws
6HQVRUKROGHU
3XQFKZDVWHIXOOVHQVRUXQLW
+DUQHVVJXLGH
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) service manuals if exist.