Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) Service Manual ▷ View online
MX-6070V MX-PN15B/C/D (PUNCH MODULE) 13 – 8
33) Connect the harness (Packed item No.8) with the punch unit
PWB.
34) Connect the opposite side of the harness (Packed item No.8) with
the interface connector.
35) Pass the harness through the wire saddle.
Stepping motor (No.7) connector
Resist sensor (No.2) connector
Harness (No.8)
Harness (no.8)
Harness (no.8)
MX-6070V MX-PN15B/C/D (PUNCH MODULE) 13 – 9
36) Tie the harness, and pass it through the wire saddle so that it can
be fixed tightly.
37) Install the rear cover of the finisher with the screw.
38) Insert the hopper from the front side of the finisher, and push the
hopper as far as it goes.
39) Cut the cover section of the finisher shown in the figure below with
the nipper.
40) For MX-FN29 (Saddle finisher), connect the interface connector
connected to the inner cover.
41) Install the inner cover of the finisher with the screw.
MX-6070V MX-PN15B/C/D (PUNCH MODULE) 13 – 10
42) Install the knobs (x2).
For MX-FN29 (Saddle finisher), also install the knob shown in the
figure below.
figure below.
43) After installing the finisher to the main unit, fix the position shown
in the figure below with the screw. (Use the screw removed at
Step 11.)
Step 11.)
44) Close the front door of the finisher.
45) Fix the harness section of the paper pass unit, and connect the
harness.
46) Fix the connector cover with the screw.
B. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet, and
turn ON the main power switch and the operation panel power
switch.
turn ON the main power switch and the operation panel power
switch.
MX-6070V MX-FN30 (FINISHER) 14 – 1
MX-6070V
Service Manual
[14] MX-FN30 (FINISHER)
1. Unpacking
A. Packed items check
B. Removal of the finisher
NOTE: It is recommendable to work by two or more persons.
1)
Open the box, and take out the accessary boxes, packed items,
and cushioning materials.
and cushioning materials.
2)
While holding the upper parts of the main unit and lifting the one
side of the machine, remove the cushioning materials. At this
time, be sure to hold up the plastic bag of the lifting side.
side of the machine, remove the cushioning materials. At this
time, be sure to hold up the plastic bag of the lifting side.
3)
While holding the upper parts of the main unit and lifting the oppo-
site side of Step.2), remove the cushioning materials and the plas-
tic bag.
site side of Step.2), remove the cushioning materials and the plas-
tic bag.
4)
Remove the slope plates (x2) and the fixing pins (x2). Fixing pins
are attached to the slope plate with the tape.
are attached to the slope plate with the tape.
5)
Align the line on the pallet and the arrow mark on the slope plate,
and mount the slope plates (x2) to the pallet with the screws (x2).
and mount the slope plates (x2) to the pallet with the screws (x2).
No.
Name
Quantity
1
Connection guide plate
1
2
Interface pass guide
1
3
Earth plate
1
4
Stapler unit staple case
1
5
Screw (M4× 14 S- tight)
4
6
Screw (M3× 6 S- tight)
5
7
Staple position label (for scanner)
1
8
Staple position label (for RSPF)
1
1
2
3
4
5
6
7
8
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) service manuals if exist.