Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) Service Manual ▷ View online
MX-6070V MX-FN31 (SADDLE STITCH FINISHER) 15 – 1
MX-6070V
Service Manual
[15] MX-FN31 (SADDLE STITCH FINISHER)
1. Unpacking
A. Packed items check
B. Removal of the finisher
NOTE: It is recommendable to work by two or more persons.
1)
Open the box, and take out the accessary boxes, packed items,
and cushioning materials.
and cushioning materials.
2)
While holding the upper parts of the main unit and lifting the one
side of the machine, remove the cushioning materials. At this
time, be sure to hold up the plastic bag of the lifting side.
side of the machine, remove the cushioning materials. At this
time, be sure to hold up the plastic bag of the lifting side.
3)
While holding the upper parts of the main unit and lifting the oppo-
site side of Step.2), remove the cushioning materials and the plas-
tic bag.
site side of Step.2), remove the cushioning materials and the plas-
tic bag.
4)
Remove the slope plates (x2) and the fixing pins (x2). Fixing pins
are attached to the slope plate with the tape.
are attached to the slope plate with the tape.
5)
Align the line on the pallet and the arrow mark on the slope plate,
and mount the slope plates (x2) to the pallet with the screws (x2).
and mount the slope plates (x2) to the pallet with the screws (x2).
No.
Name
Quantity
1
Connection guide plate
1
2
Interface pass guide
1
3
Earth plate
1
4
Stapler unit staple case
1
5
Screw (M4× 14 S- tight)
4
6
Screw (M3× 6 S- tight)
5
7
Staple position label (for scanner)
1
8
Staple position label (for RSPF)
1
1
2
3
4
5
6
7
8
MX-6070V MX-FN31 (SADDLE STITCH FINISHER) 15 – 2
6)
Put the casters of the main unit on the slope plates, and then
slowly move the main unit to the floor.
slowly move the main unit to the floor.
C. Removal of the fixing tape and protection
material
1)
Remove all fixing tapes/protection materials from the exterior.
2)
Open the front upper cover. Remove all tapes and take out the
protection materials from the stapler section.
protection materials from the stapler section.
3)
Close the front upper cover.
Ĭ
ĭ
Į
į
į
İ
ı
IJ
ij
MX-6070V MX-FN31 (SADDLE STITCH FINISHER) 15 – 3
2. Installation
Check to confirm that the firmware version is later than below.
If the version is older upgrade the firmware.
Firmware version:
Before installation, be sure to turn both the operation and main power
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
A. Preparation on the main unit
1)
Install the connection guide plate (Packed item No1.) with the
screws (x4) (Packed item No.5).
screws (x4) (Packed item No.5).
2)
Insert the rib of the interface pass guide (Packed item No.2) into
the hole of the main unit, and install it with the screw (Packed item
No.6).
the hole of the main unit, and install it with the screw (Packed item
No.6).
B. Installation of the earth plate
1)
Install the earth plate (Packed item No.3) with the screws (Packed
item No.6).
item No.6).
C. Installation of the stapler unit staple case
1)
Open the front cover. Install the stapler unit staple case (Packed
item No.4) into the stapler unit.
item No.4) into the stapler unit.
NOTE: The staple unit cannot be fixed if the power is OFF. When
installing the stapler unit staple case, insert it while holding it
so that the stapler unit cannot go deep inside.
so that the stapler unit cannot go deep inside.
A
B
C
MX-6070V MX-FN31 (SADDLE STITCH FINISHER) 15 – 4
D. Connection of the finisher to the main unit
1)
Fit the pin of the connection guide plate into the positioning hole of
the finisher.
the finisher.
E. Check of the height of the main unit and the
finisher
1)
Check that the hole on the protrusion of the connection guide
plate is located between the marking lines of the protrusion of the
finisher.
plate is located between the marking lines of the protrusion of the
finisher.
*If the hole is not located between the marking lines, perform the
height/skew adjustment.
height/skew adjustment.
F. Height/skew adjustment
1)
Open the front cover.
2)
Unscrew the screw (x1) and remove the wrench.
3)
Turn the fixing nut of the caster in the direction of the arrow as
shown with the wrench, and then loosen it.
shown with the wrench, and then loosen it.
4)
When adjusting the height, make adjustment at 4casters shown in
the picture.
the picture.
Adjust the height of the adjusting nut of the caster by turning it in
the direction of the arrow as shown. (When turning the adjusting
nut 360-degree, the height of the finisher changes about
1.75mm.)
the direction of the arrow as shown. (When turning the adjusting
nut 360-degree, the height of the finisher changes about
1.75mm.)
*For heightening the finisher: Turn the nut in [A] direction.
*For lowering the finisher: Turn the nut in [B] direction.
Marking Line
Screw
[B]
[B]
[B]
[B]
[B]
[A]
[A]
[A]
[B]
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) service manuals if exist.