DOWNLOAD Sharp AR-C200P (serv.man10) Service Manual ↓ Size: 6.26 MB | Pages: 127 in PDF or view online for FREE

SETTING UP > 41

AUTO DENSITY 
MODE

Auto; Manual

Select whether density adjustment 
and Toner Response Curve (TRC) 
compensation is automatic.
Auto: Density adjustment is 
automatically run under specified 
conditions, and reflected in the TRC 
compensation.
Manual: The printer does not 
voluntarily run density adjustment.

ADJUST DENSITY

Execute

If EXECUTE is selected, the printer will 
immediately adjust density and reflect 
it in the TRC compensation. Density 
adjustment must be executed when 
the printer is idling. It may become 
invalid if executed in any other state.

COLOUR TUNING

Print pattern

Prints the pattern for the user to adjust 
TRC. Ordinarily this function is not 
needed because TRC is automatically 
adjusted to the recommended levels 
through density adjustment and TRC 
compensation. This function permits 
TRC adjustment to your requirement by 
using the adjustment menu of 
HIGHLIGHT, MID-TONE, and DARK for 
each of CMYK. Adjustment results will 
be reflected as offset values (addition) 
to the corrections made through the 
Adjust Density/TRC Compensation 
function.

CYAN, MAGENTA, 
YELLOW OR BLACK 
HIGHLIGHT

0+1+2+3-3-2-1

Adjusts HIGHLIGHT (light area) of Cyan, 
Magenta, Yellow or Black TRC.
Plus indicates adjustment toward a 
darker level and minus toward lighter.

CYAN, MAGENTA, 
YELLOW OR BLACK 
MID-TONE

0+1+2+3-3-2-1

Adjusts MID-TONE of Cyan, Magenta, 
Yellow or BlackTRC.
Plus indicates adjustment toward a 
darker level and minus toward lighter.

CYAN, MAGENTA, 
YELLOW OR BLACK 
DARK

0+1+2+3-3-2-1

Adjusts DARK of Cyan, Magenta, Yellow 
or Black TRC.
Plus indicates adjustment toward a 
darker level and minus toward lighter.

SETTING UP > 42

CYAN, MAGENTA, 
YELLOW OR BLACK 
DARKNESS

0+1+2+3-4-3-2-1

Adjusts Cyan, Magenta, Yellow or 
Black engine density.
The Darkness settings for each CMYK 
value will be reflected as offset values 
(additions) to the corrections through 
the Adjust Density/TRC Compensation 
function.

ADJUST 
REGISTRATION

Execute

When this menu is selected, the 
printer performs an Auto Adjust 
Registration.
Must be executed in the idle state 
(Auto Registration OFF).

CYAN REGISTRATION 
- FINE ADJUST

0+1+2+3-3-2-1

Makes a fine adjustment to image 
registration in Cyan, Magenta or Yellow 
against Black in the horizontal 
direction. The adjustment is reflected 
as an offset (addition) value to the 
corrections through Auto Colour 
Registration Correction. Values are 
adjusted in increments of .026 mm. 
Example: if the paper movement is 
upward - if a value is increased (+) it 
means the image moves downward in 
relation to it.

MAGENTA 
REGISTRATION - FINE 
ADJUST

0+1+2+3-3-2-1

YELLOW 
REGISTRATION - FINE 
ADJUST

0+1+2+3-3-2-1

INK SIMULATION

Off; Euroscale

The printer has its own process 
simulation generator which simulates 
standard colours in the printer.
This function is enabled only with 
Postscript language jobs.

INK LIMIT

Dark; Medium; Light

Selects the limit of the toner layer 
thickness. If paper curl occurs in DARK 
printing, select MEDIUM or LIGHT. This 
sometimes helps reduce curl.

SETTING UP > 43

CMY 100% DENSITY

Disable; enable

Selects enable/disable 100% output 
against the CMY100% TRC 
compensation. Ordinarily, the TRC 
compensation function controls the 
appropriate print density; thus, 100% 
output is not always enabled. 
Selecting ENABLE will allow 100% 
output. In actual printing, the TCR 
values, too, are controlled by Colour 
Matching. This function is used for 
special purposes; for example, to 
specify the colour for CMYK colour 
space in PS.

POWER SAVE 
DELAY TIME

5 min; 15 min; 30 min; 
60 min; 240 min.

Sets the time before printer enters 
power save mode.

PERSONALITY

Auto emulation; PCL; 
IBM PPR III XL; Epson 
FX; Adobe PostScript; 
HP-GL2

Selects the printer emulation 
language. Note: the only printer 
languages that can be selected are 

those enabled in the Personality

section of the Maintenance menu.

USB 
PS-PROTOCOL

ASCII
RAW

Specifies PostScript (PS) 
communication protocol mode of data 
from USB. (In RAW mode, Ctrl-T is 
invalid.)

IEEE 1394
PS PROTOCOL

ASCII
RAW

Displayed only when IEEE1394 option 
board is installed.
Specifies PS communication mode of 
data from IEEE1394.
(In RAW mode, Ctrl-T is invalid).

NETWORK
PS PROTOCOL

ASCII
RAW

Displayed this Item when the network 
card is installed.
Specifies PS communication protocol 
mode of data from  the network card.
(In RAW mode, Ctrl-T is invalid.)

SETTING UP > 44

CLEARABLE
WARNING

On; Job

PCL emulation: Sets the time before 
deleting error messages. If On, press 
Error Delete switch to display error. If 
Job, error remains displayed until next 
print job is received.
PS emulation: Error messages are 
only shown during job regardless of 
setting.

AUTO CONTINUE

On; 

Sets the printer to automatically 
recover after a memory overflow or 
print overrun.

MANUAL TIMEOUT

60 sec; 30 sec; Off

Sets the time between requesting that 
paper is inserted and when the print 
job is cancelled should paper not be 
inserted.
Only works in PostScript mode.

WAIT TIMEOUT

Off; 5 sec to 300 sec 
(

90 sec)

Sets the time between receiving the 
last byte of data and the page being 
automatically ejected.
Only works in PCL mode.
In PS mode the job will be cancelled.

LOW TONER

Continue; Stop

If set to CONTINUE, allows printing to 
continue when Low toner is displayed. 
If STOP is selected - when Low toner is 
displayed, the printer goes off line.

JAM RECOVERY

ON; OFF

Sets whether or not printing will 
continue after a paper jam has been 
cleared. If set to OFF, the print job that 
was being printed when the paper jam 
occurred will be cancelled after 
clearing the paper jam. When set to 
ON, the print job will continue after 
the jam has been cleared.

ERROR REPORT

ON; 

When set to ON, prints an error report 
when internal error occurs.
Only works in PostScript mode.

LANGUAGE

English; German; 
French; Italian; 
Spanish; Swedish; 
Norwegian; Danish; 
Dutch; Turkish; 
Portuguese; Polish

Selects the printer display language.