Panasonic FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 Service Manual ▷ View online
■ Grease Application Manual for Servicing-2
㽲
Model: 7012112
Product name:
BARREL O 10CC CL 30
Price: ¥2400 ( 30 pieces )
Product name:
BARREL O 10CC CL 30
Price: ¥2400 ( 30 pieces )
Barrel
㽵
Model: 7018122
Product name:
TIP 18GA GP .033X.5 GREEN 50PC
ID / OD: 0.84mm / 1.27mm
Nozzle length: 12.7mm
Price: ¥2400 ( 50 pieces )
Product name:
TIP 18GA GP .033X.5 GREEN 50PC
ID / OD: 0.84mm / 1.27mm
Nozzle length: 12.7mm
Price: ¥2400 ( 50 pieces )
Nozzle Tip
㽵
Model: 7018122
Product name:
TIP 18GA GP .033X.5 GREEN 50PC
ID / OD: 0.84mm / 1.27mm
Nozzle length: 12.7mm
Price: ¥2400 ( 50 pieces )
Product name:
TIP 18GA GP .033X.5 GREEN 50PC
ID / OD: 0.84mm / 1.27mm
Nozzle length: 12.7mm
Price: ¥2400 ( 50 pieces )
Nozzle Tip
㽶
Model: 7023596
Product name:
10CC SMART REUSABLE DISPENSER
Price: ¥1600 ( 1 pieces )
Product name:
10CC SMART REUSABLE DISPENSER
Price: ¥1600 ( 1 pieces )
Plunger
㽳
Model: 7012180
Product name:
PISTON O 10CC RD WIPER 30
Price: ¥1700 ( 30 pieces )
Product name:
PISTON O 10CC RD WIPER 30
Price: ¥1700 ( 30 pieces )
Piston
㽴
Model: 7012198
Product name:
TIP CAP O BL 50
Price: ¥1000 ( 50 pieces )
Product name:
TIP CAP O BL 50
Price: ¥1000 ( 50 pieces )
Cap
㽲
Model: 7012112
Product name:
BARREL O 10CC CL 30
Price: ¥2400 ( 30 pieces )
Product name:
BARREL O 10CC CL 30
Price: ¥2400 ( 30 pieces )
Barrel
㽳
Model: 7012180
Product name:
PISTON O 10CC RD WIPER 30
Price: ¥1700 ( 30 pieces )
Product name:
PISTON O 10CC RD WIPER 30
Price: ¥1700 ( 30 pieces )
Piston
㽶
Model: 7012180
Product name:
10CC DISPENSGUN
Price: ¥13,000 ( 30 pieces )
Product name:
10CC DISPENSGUN
Price: ¥13,000 ( 30 pieces )
Handgun
㽴
Model: 7012198
Product name:
TIP CAP O BL 50
Price: ¥1000 ( 50 pieces )
Product name:
TIP CAP O BL 50
Price: ¥1000 ( 50 pieces )
Cap
ޣAfter assemblyޤ
ޣAfter assemblyޤ
ޣAfter assemblyޤ
ޣAfter assemblyޤ
ޣAfter use (Cap attached)ޤ
3-1. Preparation (for hand dispenser of gun type
3URFXUHIURPPDQXIDFWXUHUGLUHFWO\)
3. Preparation (for hand dispenser
3URFXUHIURPPDQXIDFWXUHUGLUHFWO\)
7-29
Nordson contact : http://www.nordson.com/en-us/directory/pages/default.aspx
■ Grease Application Manual for Servicing-3
1. Using a dispenser, apply grease on the waterproof rubber ring.
Holding example A
Holding example B
Put your hand on the barrel to stabilize the end nozzle position,
and application will be easy.
and application will be easy.
ޣConditionsޤ
DA55D manufactured by UNICONTROLS CO.,LTD.
Pressure: 0.2 MPa
Moving speed: Move hand 50 mm in approx. 20 seconds.
ψ with the above moving speed
Grease width: 1.2㨪1.5 mm
Thickness:
Pressure: 0.2 MPa
Moving speed: Move hand 50 mm in approx. 20 seconds.
ψ with the above moving speed
Grease width: 1.2㨪1.5 mm
Thickness:
0.7
㨪1 mm
*Note: The thickness should not be less than 0.7 mm
Angle Tilt the needle at an angle of 30
㨪40q
with respect to the rubber ring.
(If the needle is close to vertical, it may be stuck to the rubber ring when moving.)
(If the needle is close to vertical, it may be stuck to the rubber ring when moving.)
Moving directions
Width:
1.2~1.5mm
1.2~1.5mm
Height:
0.7~1.0mm
0.7~1.0mm
30~40
㫦
Grease
5. Application procedure
Τ
(for hand dispenser)
4. Application procedure
Σ
(for automatic machine)
7-30
■ Grease Application Manual for Servicing-4
Has the grease been applied
higher than the elastomer when
seen from the side?
higher than the elastomer when
seen from the side?
After application
Elastomer
Rib
If not, unsuccessful.
ψYou moved your hand too fast.
The pressure of dispenser was low.
ψYou moved your hand too fast.
The pressure of dispenser was low.
If not, unsuccessful.
ψYou moved your hand too fast.
The pressure of dispenser was
low.
ψYou moved your hand too fast.
The pressure of dispenser was
low.
Check
Ԙ : Width
Check
ԙ : Thickness
Has the grease been applied as far as the
rib next to the rubber ring when seen from
above?
rib next to the rubber ring when seen from
above?
Using the jig, level the grease applied on the rubber ring.
7. Application procedure
Τ
6. Check the application procedure
Σ
Fit these 2 surfaces
to each other.
to each other.
Fit it securely.
Fit it securely.
Fit the surface of elastomer
to the ridge line of the jig.
to the ridge line of the jig.
Level and cut the
grease here.
grease here.
Reverse the jig upside
down on the Kensington
part and fit it to the sur-
face of elastomer and
chassis rib.
down on the Kensington
part and fit it to the sur-
face of elastomer and
chassis rib.
7-31
■ Grease Application Manual for Servicing-5
Part where the grease has
been applied and leveled
been applied and leveled
Part where the grease has
not been applied
not been applied
The surface of the waterproof rubber on the part where
the grease has not been applied looks bright.
Insufficient grease application can be checked
by the color of the surface.
the grease has not been applied looks bright.
Insufficient grease application can be checked
by the color of the surface.
8. After application procedure
Τ
7-32
Click on the first or last page to see other FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 service manuals if exist.