Panasonic FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 Service Manual ▷ View online
6.2.
Disassembly
6.2.1.
Preparation
Before disassembling, be sure to make the following prepara-
tions.
tions.
• Shut down OS and turn off the power.
• Disconnect the AC adaptor.
• Remove other devices if they are connected.
• Disconnect the AC adaptor.
• Remove other devices if they are connected.
Attention:
• Parts (Sheet and rubber) etc. related various the Conductive
Cloth and Heat Spreader cannot be recycled. Use new parts.
6.2.2.
Removing the Battery Cover Ass'y,
Battery Pack, IO Cover Right/Left
Ass'y
Battery Pack, IO Cover Right/Left
Ass'y
1. Remove 12 Screw<N7>, remove the Battery Cover Ass'y.
2. Remove the Battery Mylar.
3. Slightly lift the front of the Battery Pack, slide the front,
2. Remove the Battery Mylar.
3. Slightly lift the front of the Battery Pack, slide the front,
and then disconnect battery connector. Remove the Bat-
tery Pack. (BATCN1)
tery Pack. (BATCN1)
4. Remove the Cable Mylar 4 and 2 Tapes.
5. Disconnect the FPC 3 locations.
5. Disconnect the FPC 3 locations.
6. Unlock the IO Cover Right/Left Ass'y, and open the cov-
ers.
7. Remove 4 Screw<N4>, remove the IO Cover Right Ass'y
and IO Cover Left Ass'y.
Screw<N4> : DRHM0215ZA
Screw<N7> : DRHM0218ZA
Screw<N7> : DRHM0218ZA
Screw<N7>
Screw<N7>
Battery Cable
Connector
(BATCN1)
(BATCN1)
Battery Pack
Battery Mylar
Battery Cover
Ass'y
Ass'y
Connector
Connector
Cable Mylar 4
Tape
Tape
IO Cover Right
Ass'y
Ass'y
IO Cover Left
Ass'y
Ass'y
IO Cover
Left Ass'y
Left Ass'y
Screw<N4>
Screw<N4>
IO Cover
Right Ass'y
Right Ass'y
6-2
6.2.3.
Removing the Media PCB, LCD
Module / Upper Case Ass'y, Lower
Case / Speaker Ass'y
Module / Upper Case Ass'y, Lower
Case / Speaker Ass'y
1. Remove 11 Screw<N3> and 2 Screw<N5>, remove the
Lower Case / Speaker Ass'y.
2. Remove the Cable Mylar 2 of 2 locations, and remove the
Conductive Tape.
3. Remove the Lock Bracket
4. Disconnect the FPC of 2 locations, flip the Media FPC.
4. Disconnect the FPC of 2 locations, flip the Media FPC.
5. Remove the Cable Mylar 2 and disconnect Media FPC.
6. Remove 2 Screw<N6>, remove the Media PCB from the
LCD Module / Upper Case Ass'y.
Screw<N3> : DRHM0214ZA
Screw<N5> : DRHM0216ZA
Screw<N6> : DRHM0217ZA
Screw<N5> : DRHM0216ZA
Screw<N6> : DRHM0217ZA
6.2.4.
Removing the 5M Camera, 2M Cam-
era Rear
era Rear
1. Remove the Cable Mylar 2 and disconnect 2M Camera
and Transfer FPC.
2. Remove the Rectangular Plastic.
Lock Bracket
Media FPC
Screw<N3>
Connector
Cable
Mylar 2
Mylar 2
Cable Mylar 2
Conductive
Tape
Screw
<N5>
<N5>
Screw<N3>
Screw<N3>
Lower Case /
Speaker Ass'y
Speaker Ass'y
Media FPC
Cable Mylar 2
Connector
Screw<N6>
Media PCB
LCD Module /
Upper Case Ass'y
Upper Case Ass'y
Transfer FPC
Rectangular Plastic
Cable Mylar 2
2M Camera
Connector
(MEDCN1)
(MEDCN1)
6-3
3. Remove 1 Screw<N1>, remove the Camera Holder.
4. Remove 2 Screw<N1>, remove the Support Bracket.
5. Remove the 3 Tapes and LVDS Cable Sheet.
6. Disconnect the LVDS Cable and remove the Camera Foil.
4. Remove 2 Screw<N1>, remove the Support Bracket.
5. Remove the 3 Tapes and LVDS Cable Sheet.
6. Disconnect the LVDS Cable and remove the Camera Foil.
(LCDCN1)
7. Disconnect the 5M Camera.
8. Remove the BOT Sheet.
8. Remove the BOT Sheet.
Screw<N1> : DRHM0212ZA
6.2.5.
Removing the RTC Battery, Charger
PCB
PCB
1. Remove the Mylar Tape and Tape.
2. Disconnect the Charger PCB Cable and RTC Battery.
2. Disconnect the Charger PCB Cable and RTC Battery.
(RTCN1)
3. Remove 2 Screw<N2>.
4. Remove the RTC Battery, Charger Holder.
5. Disconnect the Charger PCB Cable. (CHACN1)
4. Remove the RTC Battery, Charger Holder.
5. Disconnect the Charger PCB Cable. (CHACN1)
Attention:
• If folding causes damage, replace the Thermal Pad.
• When replacing only the WWAN module, remove the entire
• When replacing only the WWAN module, remove the entire
shield plate not to damage the Thermal Pad.
Screw<N2> : DRHM0213ZA
6.2.6.
Removing the DC PCB
1. Disconnect the DC PCB Cable. (DCCN1)
2. Remove 1 Screw<N1> and remove the DC IN Bracket
2. Remove 1 Screw<N1> and remove the DC IN Bracket
and DC PCB.
Screw<N1> : DRHM0212ZA
6.2.7.
Removing the GPS Antenna, Main
PCB, WWAN Module
PCB, WWAN Module
1. Remove the Thermal Pad, 3 Mylar Tape.
2. Disconnect the GPS Cable, and remove the GPS
2. Disconnect the GPS Cable, and remove the GPS
Antenna. (GPSCN1)
Camera
Holder
LVDS Cable
LVDS Cable Sheet
BOT Sheet
Tape
Camera
Foil
Foil
Tape
5M
Camera
Camera
Connector
(LCDCN1)
(LCDCN1)
Screw<N1>
Screw<N1>
Support
Bracket
Bracket
Charger PCB
Tape
Screw<N2>
RTC Battery
Charger
Holder
Holder
Connector
(CHACN1)
(CHACN1)
Connector
(RTCN1)
(RTCN1)
Charger PCB Cable
Mylar Tape
DC PCB
Screw<N1>
DC IN Bracket
Connector
(DCCN1)
(DCCN1)
GPS Antemna
Connector
(GPSCN1)
(GPSCN1)
Mylar Tape
Mylar Tape
Mylar Tape
Speaker Cable
Antenna Cable
Thermal Pad
6-4
3. Disconnect the Antenna Cable of 4 locations and Speaker
Cable. (SPKCN1, WWAN MAIN, WWNA AUX, WFCN1,
WFCN2)
WFCN2)
4. Remove 2 Screw<N2> and remove the WWAN Module.
5. Remove 4 Screw<N2>, remove the Main PCB.
Screw<N2> : DRHM0213ZA
6.2.8.
Removing the Main/AUX Antenna,
H Antenna, WLAN Antenna
H Antenna, WLAN Antenna
1. Remove 7 Mylar Tapes and remove 7 Screw<N2>.
2. Remove the Main Antenna, AUX Antenna, H Antenna
2. Remove the Main Antenna, AUX Antenna, H Antenna
and WLAN Antenna.
Screw<N2> : DRHM0213ZA
Antenna Cable
Antenna Cable
Connector
(WFCN1)
(WFCN1)
Connector
(WWAN AUX)
(WWAN AUX)
Connector
(WWAN MAIN)
(WWAN MAIN)
WWAN
Module
Module
Connector
(WFCN2)
(WFCN2)
Speaker Cable
Connector
(SPKCN1)
(SPKCN1)
Screw<N2>
WWAN Module
Screw<N2>
Screw<N2>
Main PCB
Mylar Tape
Mylar Tape
Mylar
Tape
Screw<N2>
Main Antenna
Lower Case /
Speaker Ass'y
Speaker Ass'y
H Antenna
WLAN
Antenna
Antenna
AUX
Antenna
Antenna
Screw
<N2>
<N2>
Screw
<N2>
<N2>
Screw<N2>
6-5
Click on the first or last page to see other FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 service manuals if exist.