DOWNLOAD Panasonic FZ-A1BDAAXXM / FZ-A1BDAAEE9 / FZ-A1BDAAZE9 Service Manual ↓ Size: 15.8 MB | Pages: 63 in PDF or view online for FREE

1. Attach the Media PCB to the LCD Module / Upper Case Ass'y, and tighten 2 Screw<N6>.

Tighten the Screws in the numbered order (No.1 to No.2).

2. Connect the Media FPC, and paste the Cable Mylar 2.
3. Flip the Media FPC.  

4. Connect the Media FPC to 2 locations.
5. Paste the Cable Mylar 2 to 2 locations, and paste the Conductive Tape.

6. Apply grease on the orange-covered waterproof rubber of LCD unit. 

( → P7-28 to P7-32 " ■ Grease Application Manual for Servicing" )

Screw<N6>:No.2

Screw<N6>:No.1

Media PCB

LCD Module / Upper Case Ass'y

Cable Mylar 2

Connector

Media FPC

Media FPC

Connector

Cable

Mylar 2

Cable Mylar 2

Conductive

Tape

7-17

7. Not to drop the Lock Bracket, snap Lock Bracket to Lower Case / Speaker Ass'y, attach the LCD module on it.

8. Connect the FPC to 3 locations.

9. Attach the Lower Case / Speaker Ass'y, and tighten 11 Screw<N3> and 2 Screw<N5>.

Tighten the Screws in the numbered order (No.1 to No.13).

Screw<N3> : DRHM0214ZA
Screw<N5> : DRHM0216ZA
Screw<N6> : DRHM0217ZA

Lower Case / Speaker Ass'y

LCD Module / Upper Case Ass'y

Lock Bracket

Connector

Connector

Lower Case / Speaker Ass'y

Screw<N3>:No.5

Screw<N3>:No.11

Screw<N3>:No.12

Screw<N3>:No.10

Screw<N3>:No.13

Screw<N3>:No.3

Screw<N3>:No.9

Screw<N5>:No.1

Screw<N5>:No.2

Lower Case / Speaker Ass'y

Screw<N3>:No.4

Screw<N3>:No.8

Screw<N3>:No.7

Screw<N3>:No.6

7-18

■ Connection of  Media FPC, and attachment of Media PCB

■ Attachment of Media FPC

1. Insert the Media FPC into the Media PCB connecter, and then 
    close the connecter.
2. Put 1pcs scraps of paper at the bottom of the FPC.
3. Position the Touch PCB on the LCD Module / Upper Case Ass'y.

7. Take the spray gun to blow dust away in the camera hole on 
    the LCD.
8. Remove 2M Camera protective film.

Camera hole

Camera Protective Film

4. Tighten screws*2
    

Note: 

5. Extract pieces of paper.

6. Paste 1pcs Acetate Tape on the Media PCB connecter.

    Note: Paste the acetate Tape toward the cable 

with covering the connecter.

*Notice <Screw tightening torque>

Screw<N6> = 0.165 ± 0.01N·m (1.65 ± 0.1kgf·cm)
<Screw tightening order>
Screw<N6> = 1 - 2

Key point 

Screw<N6>

1

Screw<N6>

2

The screws are not waterproof with no color on its surface. 
Tighten the screw vertically to the bottom once a time, 
aligning with the screw hole. 
Do not repeatedly perform the preceding operation.

1. Remove 2pcs Solder Mask Tape here.
2. Take Media FPC. 
    Insert the LCD Module Cable into the Media FPC connector, 
    close the connector, and then paste 1pcs Tape on the connector. 
    

Note:

3. Remove the FPC adhesive*2 as shown in the figure. 
    Position the FPC on the LCD Module / Upper Case Ass'y.
4. Insert the Media FPC into the LCD Module connector, close the 
    connector, and then paste 1pcs Tape on the connector.
5. Postion 1pcs Conductive Tape at the place as shown in the figure.

The connector edge must be aligned with 
the positioning line after the connector is 
closed.

Paste the Acetate Tape toward the 
cable with covering the connector.

Position the Conductive Tape 
according to the edge of the 
transverse Conductive Tape 
and the positioning line of the 
LCD Module / Upper Case Ass'y.

LCD Module connector

Align the connector edge with the positioning line after 
the connector is closed. 

7-19

■ What to check before the assembled

The Tape pasting on the left cannot 
exceed the edge of the square. 
The Tape pasting on the right should 
cover the center of the RTC Battery.

1. Put Key lock Bracket in 
    the slot in the Lower Case / 
    Speaker Ass'y.

4. Insert the cables*3 as shown in the 
    figure, and then lock it.

2. Check whether all cables are 
    inserted well, and whether all tapes 
    are pasted.
3. Close the LCD to the lower cover.

    Note: 
    1.

    2. 

    3. 

The groove side faces downwards.

Expose the white positioning line 
on the back.
Do not touch the oil around by 
hands.
There is no Wi-Fi antennas 
in the corresponding the 
LCD frame of Media PCB.

Note: 
Insert the cables parallelly to the end.

Note: 
The groove side of Key lock 
Bracket is towards back 
and downward.

7-20