Panasonic CF-30FTSAZAM Simplified Service Manual ▷ View online
7-16
7.2.5.
Setting the Display Unit
1. Fix the Display Unit using the 4 Screws. <N9> No1 to No4
2. Fix the Display Unit using the 2 Screws. <N10> No1, No2
2. Fix the Display Unit using the 2 Screws. <N10> No1, No2
Note:
Tighten the Screws in the numbered order (No1 to No2).
Tighten the Screws in the numbered order (No1 to No4).
Tighten the Screws in the numbered order (No1 to No4).
Screws <N9>: DRYN4+J10FKL
Screws <N10>: DXSB4+15FNLB
Screws <N10>: DXSB4+15FNLB
7.2.6.
Setting the Handle and Power SW
1. Set the WM SW using the 2 Screws. <K2-42>
2. Set the Power SW.
3. Set the Handle.
4. Fix the Handle Base L and R using the 2 Screws. <K2-41>
5.
2. Set the Power SW.
3. Set the Handle.
4. Fix the Handle Base L and R using the 2 Screws. <K2-41>
5.
Screws <K2-41>: DRSN4+6FKLT
Screws <K2-42>: DXQT26+D4NLT
Screws <K2-42>: DXQT26+D4NLT
<N9>
<N9>
<N9>
<N9>
Display Unit
<N10>
<N10>
No.1
No.2
No.3
No.4
No.1
No.2
Handle
Handle Base L
Handle Base R
Power
SW
<K2-41>
<K2-41>
WM SW
<K2-42>
7-17
7.2.7.
Setting the Palm Top Cover Sheet, Palm Top Cover, Touch Pad Adhesion Seat, Touch
Pad SW Knob, LED PCB And SW LED PCB
Pad SW Knob, LED PCB And SW LED PCB
1. Set the SW LED PCB.
2. Attach the Power LED Packing Sheet to the LED Spacer
2. Attach the Power LED Packing Sheet to the LED Spacer
Sheet.
3. Attach the LEDX6 Spacer Sheet on the SW LED PCB.
4. Fix the SW LED PCB using the Screw. <K2-42>
5. Attach the PW LED Sheet.
6. Pass the Cable of LED PCB through the hole 1 on the Top
4. Fix the SW LED PCB using the Screw. <K2-42>
5. Attach the PW LED Sheet.
6. Pass the Cable of LED PCB through the hole 1 on the Top
Cabinet, then set the LED PCB.
7. Attach the LES Spacer Sheet on the LED PCB.
8. Set the touch Pad SW Knob In and Touch Pad SW Knob
9. Attach the TP Bottom Tape to the Touch Pad.
8. Set the touch Pad SW Knob In and Touch Pad SW Knob
9. Attach the TP Bottom Tape to the Touch Pad.
10. Pass the Cables of the Touch Pad through the hole 2 on the
Top Cabinet, set the touch Pad.
11. Attach the Touch Pad Adhesion Seat.
12. Fix the Palm Top Cover using the 5 Screws. <N29> No1 to
No5
13. Attach the Palm Top Cover Sheet.
Note:
Tighten the Screws in the numbered order (No1 to No5).
Screws <K2-42>: DRQT26+D4NLT
Screws <N29>: DRQT26+E3FNL
Screws <N29>: DRQT26+E3FNL
■ Preparation of SW LED FPC
Palm Top Cover Sheet
<N29>
<K2-42>
Palm Top Cover
PW LED Sheet
Touch Pad Adhesion Seat
Touch Pad
LED PCB
Touch Pad SW Knob
Touch Pad
SW Knob In
PW LED
PCB
SW LED
PCB
<N29>
<N29>
<N29>
<N29>
No.4
No.2
No.5
No.3
No.1
Hole 1
Hole 2
0.5
0.5
1 1
Attach the Tape
Attach the Sheet
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Use a pinset.
White Full Line : Mountain Fold
Attach it not to overlap the SW leg.
Flex Notch Standard 0 1
White Dotted Line : Valley Fold
SW-LED FPC Ass'y
7-18
■ Assembly of Power SW
12 2
25 2
10 1
3 5
Attach the Battery Cushion
Attach the DC Gasket
Tighten of Screw
Power SW LED
Panel is set
Panel is set
FPC Power SW is set
Safety Working
Attach the TP
FPC Tape
FPC Tape
Cable Power
Connection
Connection
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Battery Pack Insertion Slot
Attach the Battery Slide Sheet (on Battery Cushion)
Avoid air leaking into it. Avoid coming off 4 corners.
Fit to the line.
Ensure the upper and lower Flex holes match.
CAB Wall
Connection Direction
Connection Direction
Top
Bottom
Match the Cabinet slit
and the tape slit.
Do not run the Cabinet
edge out of the tape slit.
and the tape slit.
Do not run the Cabinet
edge out of the tape slit.
CAUTION
S1:Insulation S2:Pinching Cables S3:Sharp Edge
S4:Part No. Check S5:Others
S4:Part No. Check S5:Others
S3
7-19
■ Assembly of Palm Top Cover
Notes:
Attach the Pad
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
After attaching, trace around TP,
SW and circumference with finger.
SW and circumference with finger.
Ensure that the PAD and the button neck
are attached with adhesive firmly.
are attached with adhesive firmly.
A
B
Order of fixing
Screw
Screw
Screw
Screw
Screw
Tighten of
Screw
Screw
Tighten of
Screw
Screw
Tighten of
Screw
Screw
Tighten of
Screw
Screw
Tighten of
Screw
Screw
Palm Top Cover
is set
is set
Touch Pad SW Knob
Rubber is set
Rubber is set
FFC 6LED is set
Attach the
PWB 6LED
PWB 6LED
LEDX6 Spacer
Sheet is set
Sheet is set
Touch Pad SW Knob
In is set
In is set
Attach the Pad WP Sheet
Palm Top
Cover
Cover
Avoid running over the protrusion attached
to the protrusion side of the upper Cabinet.
to the protrusion side of the upper Cabinet.
Put to the arrow direction
and attach it.
and attach it.
Insert FPC into the hole
of upper cabinet.
of upper cabinet.
Do not come over
the Pad edge.
the Pad edge.
Attach the TP
Bottom Tape
Bottom Tape
Put to the left and set.
Protrusion
Insert FFC into the hole
of upper cabinet.
of upper cabinet.
Note: Separation
Notes for Separation
Do not attach the
oil on both sides.
Avoid running over!
oil on both sides.
Avoid running over!
Attach within the range of the
upper Cabinet concave.
upper Cabinet concave.
Palmtop Preparation
Attach the Washer
Attach it not to cover the hole
of LEDX6 Spacer Sheet.
Attach it not to cover the hole
of LEDX6 Spacer Sheet.
Attach the Washer
(See below)
(See below)
Process the speaker lead wire not to
put inside when applying the load.
put inside when applying the load.
Using the pressure jig, Ensure the
loads are applied equally.
loads are applied equally.
Make sure the adhesive materials
are attached closely on the whole
side.
are attached closely on the whole
side.
Click on the first or last page to see other CF-30FTSAZAM service manuals if exist.