Panasonic CF-30FTSAZAM Simplified Service Manual ▷ View online
7-32
7.2.16. Setting the KB Cable Cover, Keyboard and LCD Cable Cover
1. Set the Keyboard onto the Computer.
2. Connect the 2 Cables to the 2 Cables. (CN13,CN14)
3. Fix the KB Cable Cover using the 7 Screws. <N29> No1 to
2. Connect the 2 Cables to the 2 Cables. (CN13,CN14)
3. Fix the KB Cable Cover using the 7 Screws. <N29> No1 to
No7
4. Set the LCD Cable Plate.
5. Fix the LCD Cable Cover using the 3 Screws. <N29> No1 to
5. Fix the LCD Cable Cover using the 3 Screws. <N29> No1 to
No3
Note:
Tighten the Screws in the numbered order (No1 to No7).
Tighten the Screws in the numbered order (No1 to No3).
Tighten the Screws in the numbered order (No1 to No3).
Screws <N29>: DRQT26+E3FNL
■ Arranging the Keyboard
<N29>
<N29><N29>
<N29>
<N29>
<N29>
<N29>
<N29>
<N29>
<N29>
to Connector
(CN14)
Connector
(CN13)
Connector
(CN14)
to Connector
(CN13)
KB Cable Cover
LCD
Cable Cover
LCD
Cable Plate
Keyboard
No.6
No.4
No.1
No.5
No.3
No.7
No.2
No.1
No.2
No.3
Attach the Keyboard
Spacer Tape
Spacer Tape
Attach the Keyboard
Spacer Sheet
Spacer Sheet
Attach the Keyboard
Back Plate
Back Plate
Keyboard US is installed
Attach the Keyboard Fook Spacer Lower
Plate hole
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
1. Attach the Keyboard US and Keyboard Spacer. (KB Preparation)
2. Attach the Keyboard Back Plate and Keyboard Spacer Sheet. (Plate Preparation)
2. Attach the Keyboard Back Plate and Keyboard Spacer Sheet. (Plate Preparation)
(Ensure Keyboard Spacer Sheet does not run over the level of Keyboard Back Plate.)
3. Attach the prepared KB to the prepared plate.
(Insert the KB protrusions into the plate holes and determine the position.)
: Fit to the edge of plate (KBD back plate).
Both sides should not come over the plate.
7-33
7.2.17. Setting the KB Cover, Hinge Cover L, Hinge Cover R and Keyboard
1. Insert the front hooks of the Keyboard to the Top Cabinet in
order, and set the Keyboard.
2. Fix the Hinge Cover L and R using the 3 Screws <N6> No1
to No3
3. Fix the Hinge Cover L and R using the 2 Screws. <N2>
No1, No2
4. Fix the Bluetooth PCB using the Screw. <N6>
5. Fix the KB Cover using the 4 Screws. <N6> No1 to No4
5. Fix the KB Cover using the 4 Screws. <N6> No1 to No4
Note:
Tighten the Screws in the numbered order (No1 to No4).
Tighten the Screws in the numbered order (No1 to No3).
Tighten the Screws in the numbered order (No1, No2).
Tighten the Screws in the numbered order (No1 to No3).
Tighten the Screws in the numbered order (No1, No2).
Screws <N2>: DRHM5054XA
Screws <N6>: DRQT26+E4FKL
Screws <N6>: DRQT26+E4FKL
7.2.18. Setting the HDD
1. Set the HDD FPC to HDD.
2. Attach the Heater Ins Sheet and Sheet to HDD.
3. Attach the Heater to HDD.
4. Attach the 6 HDD Forming MFYPC and the two HDD
2. Attach the Heater Ins Sheet and Sheet to HDD.
3. Attach the Heater to HDD.
4. Attach the 6 HDD Forming MFYPC and the two HDD
Terminal Plate Upper to the HDD Damper Ass'y.
5. Attach the six HDD Forming MFYPC and the two HDD
Terminal Plate Upper to the HDD Damper Ass'y.
6. Set the HDD Damper Ass'y to HDD.
7. Attach the Side Cushion to the HDD L Case Ass'y.
8. Set the HDD U Case Ass'y and the HDD L Case Ass'y, and
7. Attach the Side Cushion to the HDD L Case Ass'y.
8. Set the HDD U Case Ass'y and the HDD L Case Ass'y, and
set the two Tabs of the HDD L Case Ass'y.
9. Fix the HDD U Case Ass'y and the HDD L Case Ass'y using
the 4 Screws <K1-17> and Screw <K1-16>.
Screws <K1-16>: DFHE5025XA
Screws <K1-17>: DRQT2+E8FKL
Screws <K1-17>: DRQT2+E8FKL
<N6>
<N6>
<N6>
<N6>
<N6> <N2>
<N2>
<N6> <N6>
KB Cover
Hinge Cover L
Hinge Cover R
Keyboard
<N6>
Bluetooth PCB
No.1
No.3
No.2
No.4
No.1
No.2
No.3
No.1
No.2
HDD U Case Ass'y
HDD FPC
Heater Ins Sheet
HDD L
Case Ass'y
Case Ass'y
HDD
Sheet
<K1-17>
<K1-17>
<K1-16>
SATA Guard
Heater
HDD
Damper
Ass'y
Damper
Ass'y
7-34
■ Preparation oh HDD ASSY
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Fit to the corner.
Turn it to the board side (back side).
HDD INS SHEET
HDD TAPE S
Safety Working
Insert the HDD FPC Ass'y
Connect the Connector
Valley Fold
Mountain Fold
1. Do not gouge when inserting and removing the socket.
2. Do not drop HDD or add any impacts on it.
3. Insert CN into the end firmly.
4. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
2. Do not drop HDD or add any impacts on it.
3. Insert CN into the end firmly.
4. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Do not bend the bending
part of Heater
part of Heater
Attach it pushing the shaded
part not to push the fuse.
part not to push the fuse.
PET TAPE
HEATER FIXED
TAPE
Center
HEATER
CAUTION
S1:Insulation S2:Pinching Cables S3:Sharp Edge
S4:Part No. Check S5:Others
S4:Part No. Check S5:Others
S4
7-35
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
HDD Damper Ass'y
Make sure the product with black
sheet on the yellow sponge.
sheet on the yellow sponge.
HDD Set Insert after removing the Release Paper of the two-sided tape.
Fold the FPC from the board edge.
HDD Ass'y
Remove the Release Paper on
the back, close and attach it.
the back, close and attach it.
Attach it to HDD closely not to loosen.
Push and bend
Do not place the damper
over the plate of FPC.
Do not place the damper
over the plate of heater.
Longer Direction
Sheet
HDD Thermal Plate
1
3
1
2
1
3
0
1
1 3
1 3
Attach the HDD Cushion (Yelllow)
Attach the HDD Cushion (Yelllow)
Attach the HDD Cushion
(Black)
(Black)
Attach the HDD
Thermal Plate
Thermal Plate
HDD Cushion (Black)
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Prepare the metal plate bend.
Do not bend it at a sharp
angle to put natural R.
angle to put natural R.
To the level of attaching
closely in this range
closely in this range
When attaching HDD Cushion (Yellow) and HDD Cushion (Black),
set the bending part of the metal plate up.
set the bending part of the metal plate up.
Metal Plate
Click on the first or last page to see other CF-30FTSAZAM service manuals if exist.