Panasonic CF-30FTSAZAM Simplified Service Manual ▷ View online
7-28
■ Assembly of USB PCB
Tighten of
Screw
Screw
Tighten of
Screw
Screw
Tighten of Screw
EXT Antenna PCB
is set
is set
W-LAN Cable
Connection
Connection
Safety Working
Safety Working
Attach the Tape
Attach the Antenna Cable Sheet
Antenna Cable
Plate is set
Plate is set
Order of fixing
Screw
Screw
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Connect the coaxial cable from LCD.
Set on the top.
Process the cable from LCD.
Fit to the groove.
Difference : 1 or less
Difference : 1 or less
Along the groove
Pull W-LAN Cable out to the surface from the hole.
CAUTION
S1:Insulation S2:Pinching Cables S3:Sharp Edge
S4:Part No. Check S5:Others
S4:Part No. Check S5:Others
S2
S2
Safety Working
Cable USB is set
PCB USB Sub is set
Tighten of Screw
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Match to the CN edge.
Difference: less than 1
Difference: less than 1
Match to the board edge.
Difference: less than 1
Difference: less than 1
Attach the kapton tape into CD Edge Sheet.
S1
7-29
7.2.14. Setting the DIMM Cover and Bottom Cover
1. Set the Bottom Cover.
2. Fix the Bottom Cover using the 6 Screws. <N8> No1 to No6
3. Fix the Bottom Cover using the 11 Screws. <N6> No1 to
2. Fix the Bottom Cover using the 6 Screws. <N8> No1 to No6
3. Fix the Bottom Cover using the 11 Screws. <N6> No1 to
No11
4. Fix the Bottom Cover using the 2 Screws. <N17> No1, No2
5. Set the DIMM memory card.
6. Attach the DIMM Heat Plate.
7. Fix the DIMM Stopper Base using the 2 Screws. <N2>
8. Fix the DIMM Cover using the 5 Screws. <N1>
5. Set the DIMM memory card.
6. Attach the DIMM Heat Plate.
7. Fix the DIMM Stopper Base using the 2 Screws. <N2>
8. Fix the DIMM Cover using the 5 Screws. <N1>
Screws <N1>: DRHM0002ZA
Screws <N5>: DRQT26+D4FKL
Screws <N6>: DRQT26+E4FKL
Screws <N8>: DRSB3+8FKL
Screws <N17>: DRQT26+E6FKL
Screws <N5>: DRQT26+D4FKL
Screws <N6>: DRQT26+E4FKL
Screws <N8>: DRSB3+8FKL
Screws <N17>: DRQT26+E6FKL
Note:
Tighten the Screws in the numbered order (No1 to No6).
Tighten the Screws in the numbered order (No1 to No11).
Tighten the Screws in the numbered order (No1, No2).
Tighten the Screws in the numbered order (No1 to No5).
Tighten the Screws in the numbered order (No1 to No11).
Tighten the Screws in the numbered order (No1, No2).
Tighten the Screws in the numbered order (No1 to No5).
<N8>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N8>
<N8>
<N8>
Bottom Cover
DIMM Memory Card
DIMM Stopper Base
DIMM Heat Plate
DIMM Cover
<N1>
<N1> <N1>
<N1>
<N1>
<N6>
<N6>
<N8><N17>
<N6>
No.4
No.5 No.2 No.3
No.1
No.1
No.2
No.3
No.4
No.5
No.6
No.6
<N17>
No.7
No.7
<N6>
No.8
No.9
No.10
No.11
No.1
No.2
No.3
No.4
No.5
<N8>
No.6
7-30
■ Preparation of DIMM Cover
LCD Cable Cover is set
Keyboard Cable Cover is installed
Attach the LCD Cable Cover Cushion
Attach the Keyboard Cable Cover Cushion
Safety Working
Safety Working
Attach the CD Edge Sheet
Attach the CD Edge Sheet
4 6mm
4 6mm
0 1mm
1.5 2.5mm
* Notes:
1. Apply the load when attaching the attaching parts. 20N to 30N (2 to 3Kgf)/cm2
1. Apply the load when attaching the attaching parts. 20N to 30N (2 to 3Kgf)/cm2
0 0.5mm
0 0.5mm
0 0.5mm
0 0.5mm
DIMM Cover is set
Attach the DIMM Cover Cushion
Attach the DIMM Cover Spacer
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
CAUTION
S1:Insulation S2:Pinching Cables S3:Sharp Edge
S4:Part No. Check S5:Others
S4:Part No. Check S5:Others
S3
S3
7-31
7.2.15. Setting the GPS PCB and Bluetooth PCB
1. Fix the GPS BT Angle and GPS PCB using the 2 Screws.
<N11>
2. Connect the Cable to the Connector on GPS PCB.
3. Fix the GPS Ass’y using the 4 Screws. <N12>
4. Connect the Cable to the Connector. (CN25)
3. Fix the GPS Ass’y using the 4 Screws. <N12>
4. Connect the Cable to the Connector. (CN25)
Screws <N11>: DFHE5025XA
Screws <N12>: DXQT2+F3FNL
Screws <N12>: DXQT2+F3FNL
■ Cautions for Setting GPS ASSY and BT PCB ASSY
GPS PCB
Bluetooth
PCB
Connector(CN25)
<N11>
<N11>
GPS BT Angle
<N12>
<N12>
<N12>
<N12>
to Connector
(CN25)
Safety Working
Safety Working
Safety Working
8 1
10 2
Main Antenna
Sub Antenna
Bluetooth Cable
Whip Antenna Cable
Whip Antenna Cable
Main Antenna Cable
GPS Antenna Cable
0 2
0 2
Sub Antenna Cable
* Notes:
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
Fit to the plate squeeze line. 1
Attach the Tape
Put the Cable along
the Cabinet side and
tape it firmly.
the Cabinet side and
tape it firmly.
Match to the boss center.
Cabinet Level Standard
Tolerance 0 to 1
Process the wire into the groove.
Tolerance 0 to 1
Process the wire into the groove.
Pass the Cable behind
the Cabinet protrusion.
the Cabinet protrusion.
Attach the Cable Sheet into
Main Cable and Whip Cable.
Main Cable and Whip Cable.
Attach the Cable Sheet into
Sub Cable and GPS Cable.
Sub Cable and GPS Cable.
Ensure that the wrapping
direction is right.
direction is right.
Avoid coming over the groove.
Ensure that the wrapping
direction is right.
direction is right.
Connect into the coaxial Connector.
Process the wire to the
back from the aperture.
back from the aperture.
Insert the
cable plug.
cable plug.
Process the wire of whip ANT cable from
LCD to the back from the aperture.
LCD to the back from the aperture.
1. Do not gouge when inserting and removing the plug.
2. Do not damage the coating when handling the cable.
2. Do not damage the coating when handling the cable.
Bluetooth Cable
GPS Antenna
CAUTION
S1:Insulation S2:Pinching Cables S3:Sharp Edge
S4:Part No. Check S5:Others
S4:Part No. Check S5:Others
S2
S2
S2
Click on the first or last page to see other CF-30FTSAZAM service manuals if exist.