DOWNLOAD Panasonic KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 Service Manual ↓ Size: 11.38 MB | Pages: 127 in PDF or view online for FREE

37

(1) Remove the Side Plate Assembly 

and the Conveyor Belt 2.

(2) Pull the Pulley (arrow 

) while unlocking the hook (arrow 

) 

and remove the Pulley.

After reassembling the Pulley, be sure to check that the 
Pulley is locked to the Exit Roller by pulling the Pulley.

(3) Slide and remove the Bearing from the Exit Roller (arrow 

).

(4) Unlock the hook of the Conveyor Roller Bearing (arrow 

).

(5) Unlock the Exit Roller by turning the Conveyor Roller 

Bearing (arrow 

).

(6) Slide the Exit Roller with the Conveyor Roller Bearing and

remove it (arrow 

).

(7) Remove the Support Bearing.

(8) Remove the Polyslider.
(9) Remove the Conveyor Roller Bearing from the Exit Roller.

Before reassembling the roller, be sure to check that the 
Support Bearing is installed. 

Bearing

Pulley

Hook

Exit Roller

Exit Roller

Conveyor Roller Bearing

Support Bearing

Exit Roller

Support Bearing

Conveyor Roller Bearing

Polyslider

Support Bearing

38

(1) Remove the Paper Feed Roller Assembly.

(See Appendix (Operating Manual P.47))

(2) Remove the Polyslider and the Spacer.
(3) Slide and remove the Feed Roller Assy.

.

(4) Remove the 2 Polysliders.
(5) Slide and remove the Feed Roller Assy.

Make sure to re-assemble the Feed Roller Assy, paying
attention to the arrow marked on each assy.

Paper Feed Roller Shaft

Spacer

Polyslider

Feed Roller Assy

OK

Paper Feed Roller Shaft

Polyslider

Feed Roller Assy

39

IC11 (Flash memory on CONTROL Board) 

STARTING SENSOR Board

ULTRASONIC SENSOR (G) Board

CIS(F)

CIS(B)

Scanning Glass (F)

Scanning Glass (B)

Drive roller

Exit roller

Others (when assembling or disassembling 

parts(Conveyor etc.) which will affect the 

scanning positions.)

Replaced circuit board or part

USB ID

Double feed

Length

Horizontal Position

Vertical Position

Horizontal Position

Vertical Position

All Position

Shading

Required adjustment

Individual Position

Front

Back

ULTRASONIC SENSOR (R) Board

: Excecute the required adjustment.

: Excecute “All position” or “Individual position” adjustment.

40

According to the following, wipe off the dirt from the surface of each part and replace Limited Life Parts to maintain the performance
of the scanner.

C: Clean each of the following parts every 2,000 sheets scanned.
R: Replace rollers (Paper Feed, DFP) every 100,000 sheets scanned. 

• PC will notify users of cleaning and replacement timing when running the utility software after Clean or Replace Roller Counter

reaches the Clean or Replace Roller Timing (Default setting: Cleaning cycle 2,000, Exchange cycle 100,000).

• The maintenance schedule was determined according to paper standards (A4: 80 g/m² / Letter: 20 lb.), which can vary greatly

between users. Therefore, the schedule may vary depending on usage conditions. As a countermeasure, scanner counter of
setting value (maintenance cycle) can be changed. How to set the scanner counter, please refer to Chapter 10.

• Please refer to the 16 Appendix (Operating manual P.10) for the roller cleaning paper.

Refer to the concerned pages of Operating Manual (See 16. Appendix (Operating Manual P.39).)

Refer to the concerned pages of Operating Manual (See 16. Appendix (Operating Manual P.45).)

KV-SS058 

Clean each part 
every 2(x 1000) 
Sheets 
scanned.

After cleaning the Paper Feed and DFP 
Rollers, execute “Clear Counter” for 
cleaning roller with Service Utility. 
After replacing the rollers, execute “Clear 
Counter” for replacing roller. 
(See Scanner Condition (

Paper Feed Roller

C

C

C

C

R

DFP Roller

C

C

C

C

R

Conveyor Roller

C

C

C

C

-

Exit Roller

C

C

C

C

-

Free Rollers

C

C

C

C

-

Scanning glass (F)

C

C

C

C

-

Scanning glass (B)

C

C

C

C

-

Double Feed Detector 
(Generator)

C

C

C

C

-

Double Feed Detector 
(Receive) 

C

C

C

C

-