Panasonic KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 Service Manual ▷ View online
33
8.4.8.
STARTING SENSOR Board
8.4.9.
ULTRASONIC SENSOR (R) Board
(1) Remove the CONTROL Board's Box.
(See 8.4.5. CONTROL Board’s Box)
(2) Unlock the hook and remove the STARTING SENSOR
Board.
(3) Disconnect the connector.
Hook
STARTING SENSO Board
Connector
(1) Remove the CONTROL Board's Box.
(See 8.4.5. CONTROL Board’s Box)
(2) Remove the screw D and remove the ULTRASONIC
SENSOR (R) Board.
(3) Disconnect a cable from Board.
ULTRASONIC SENSOR (R) Board
D
34
8.4.10. CIS (F)
8.4.11. Side Plate Assembly
(1) Remove the CONTROL Board's Box.
(See 8.4.5. CONTROL Board’s Box)
(2) Remove the black tape that secure a coil of the Flat Cable.
(3) Remove the 2 screws D.
(4) Unlock the 2 hooks and remove CIS (F) (with the CIS
(3) Remove the 2 screws D.
(4) Unlock the 2 hooks and remove CIS (F) (with the CIS
Cover).
(5) Unlock the connector on the CIS.
(6) Remove the flat cable and CIS Cover from the CIS (F).
(6) Remove the flat cable and CIS Cover from the CIS (F).
CIS (F)(with the CIS Cover)
D
Hook
D
Flat Cable
Black Tape
CIS (F)
CIS Cover
Unlock
(1) Remove the Front Cover.
(See 8.2.5. Front Cover)
(2) Remove the 2 screws D and screw C.
(3) Remove Side Plate Assembly.
(3) Remove Side Plate Assembly.
Reassembling Note:
a: When installing the Side-Plate Assembly, make sure to
position the Idle Pulley of the assembly.
Assemble the pulley to outside of the Conveyor Belt 2.
Assemble the pulley to outside of the Conveyor Belt 2.
b: After installing the Side-Plate Assembly, adjust the belt
tension as follows.
(1) Loosen spring plate screw. (Proper belt tension will be
(1) Loosen spring plate screw. (Proper belt tension will be
adjusted by elastic force of the spring.)
(2) Tighten the screw.
Idle Pulley
Conveyor Belt 2
NG
OK
Screw
Screw
D
D
Side Plate Assembly
C
35
8.4.12. Conveyor Motor
(1) Remove the Side Plate Assembly.
(See 8.4.11. Side Plate Assembly)
(2) Remove the connector.
(3) Remove the 2 screws C.
(4) Rotate the motor 180 degrees in front and remove it.
(3) Remove the 2 screws C.
(4) Rotate the motor 180 degrees in front and remove it.
Conveyor Motor
C
C
Conveyor Motor
Connector
36
8.4.13. Conveyor Roller
(1) Remove the Side Plate Assembly and Conveyor Belt 2.
(See 8.4.11. Side Plate Assembly)
(2) Pull the Pulley (arrow
2
) while unlocking the hook (arrow
1
)
and remove the Pulley.
Reassembling Note:
After reassembling the Pulley, be sure to check that the
Pulley is locked to the Conveyor Roller by pulling the Pulley.
Pulley is locked to the Conveyor Roller by pulling the Pulley.
(3) Slide and remove the Bearing from the Conveyor Roller
(arrow
3
).
(4) Unlock the hook of the Conveyor Roller Bearing (arrow
4
).
(5) Unlock the Conveyor Roller by turning the Conveyor Roller
Bearing (arrow
5
).
(6) Slide the Conveyor Roller with the Conveyor Roller Bearing
(arrow
6
) and remove it (arrow
7
).
(7) Remove the Support Bearing.
(8) Remove the Polyslider.
(9) Remove the Conveyor Roller Bearing from the roller.
(9) Remove the Conveyor Roller Bearing from the roller.
Reassembling Note:
Before reassembling the roller, be sure to check that the
Support Bearing is installed.
Support Bearing is installed.
Bearing
Pulley
Hook
1
2
3
Conveyor
Roller
Roller
Conveyor Roller
Conveyor
Roller
Bearing
Roller
Bearing
6
7
4
5
Support
Bearing
Bearing
Support
Bearing
Bearing
Conveyor Roller Bearing
Support Bearing
Polyslider
Click on the first or last page to see other KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 service manuals if exist.