Panasonic KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 Service Manual ▷ View online
29
8.3.6.
CIS (B)
8.3.7.
Wiring of Upper Chassis
(1) Remove the Top Cover.
(See 8.3.2. Top Cover)
(2) While pushing the hook on the PALEL Board side inward
with the fine screwdriver (arrow
1
), push the CIS(B) from the
round hole (arrow
2
).
(3) Remove CIS (B) Assembly (arrow
3
).
(4) Unlock the connector and disconnect the FFC cable.
(5) Remove the CIS Cover B with 2 CIS Springs, while releasing
(5) Remove the CIS Cover B with 2 CIS Springs, while releasing
the 9 hooks.
(6) Remove CIS (B) from Scanning Glass (B).
CIS Cover B
Hooks
CIS Spring
CIS (B)
Scanning Glass (B)
CIS (B) Connector
Unlock
FFC Cable
Hooks
Scanning Glass (B)
Boss of
CIS (B)
CIS (B)
PANEL
Board
Board
1
3
<Back side>
2
Screwdriver
30
8.4.
Lower Chassis
8.4.1.
Bottom Cover
8.4.2.
Bottom Plate
(1) Remove the Rear Cover.
(See 8.2.3. Rear Cover)
(2) Remove the Front Cover.
(See 8.2.5. Front Cover)
(3) Slide the Bottom Cover (arrow
2
) while releasing the hook
(arrow
1
).
Then, remove the cover (2 arrows
3
).
Hook
Bottom Cover
Bottom Plate
3
1
3
2
(1) Remove the Bottom Cover.
(See 8.4.1. Bottom Cover)
(2) Remove the 6 Screws C and remove the Bottom Plate.
Bottom Plate
C
C
C
C
C
C
31
8.4.3.
CONTROL Board
8.4.4.
PAPER SENSOR Board
(1) Remove the Bottom Plate.
(See 8.4.2. Bottom Plate)
(2) Unlock the CN1 and CN3 connectors.
(3) Disconnect all cables (4 cables and 4 flat cables) from the
(3) Disconnect all cables (4 cables and 4 flat cables) from the
connectors on the Board.
(4) Remove the 5 screws C and the clip.
(5) Remove the CONTROL Board.
(5) Remove the CONTROL Board.
Reassembling Note:
Do not forget to install the blue clip as follows.
1. Tighten the screw A with the blue
clip and the PCB.
2. Bent the clip inserting the tip of the
clip between the harness and the
PCB.
PCB.
3. Adjust the height of the clip to a
position lower than the plate.
Plate
CONTROL Board
C
Connector
Connector
C
C
Coating Clip
C
Connector
Flat Cable
C
Flat Cable
CN1
CN3
Unlock CN1 & CN3
Unlock
Unlock
(1) Remove the Rear Cover.
(See 8.2.3. Rear Cover)
(2) Remove the PAPER SENSOR Board while unlocking the
hook.
(3) Disconnect the connector.
Hook
PAPER SENSOR Board
Connector
32
8.4.5.
CONTROL Board’s Box
8.4.6.
FAN
8.4.7.
DOOR DETECTION Board
(1) Remove the Bottom Plate.
(See 8.4.2. Bottom Plate)
(2) Disconnect all connectors on the CONTROL Board.
(See 8.4.3. CONTROL Board)
(3) Release the cable from the clamper.
(4) Remove the screw C, 4 screws D, and screw D with FG
(4) Remove the screw C, 4 screws D, and screw D with FG
cable.
(5) Remove the CONTROL Board's Box from the unit.
CONTROL Board
D
D
C
Clamper
D
D
(with FG Cable)
CONTROL Board’s Box
Flat Cable
Flat Cable
Connector
Connector
(1) Remove the CONTROL Board's Box.
(See 8.4.5. CONTROL Board’s Box)
(2) Remove the 2 screws D.
(3) Disconnect the FAN.
(3) Disconnect the FAN.
CONTROL Board’s Box
D
D
FAN
(1) Remove the CONTROL Board's Box.
(See 8.4.5. CONTROL Board’s Box)
(2) Unlock the hook and remove the DOOR DETECTION
Board.
(3) Disconnect the connector.
㻴㼛㼛㼗
DOOR DETECTION Board
Connector
Click on the first or last page to see other KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 service manuals if exist.