Panasonic KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 Service Manual ▷ View online
25
8.2.2.
Side Cover (L)
8.2.3.
Rear Cover
(1) Push the Door Open Button to open the ADF Door.
(2) Unlock the 2 hooks to release the bottom side of the Side
(2) Unlock the 2 hooks to release the bottom side of the Side
Cover (L).
Note:
Pay attention to breaking of the hook tip.
(3) Slide upward and remove it in the direction of the arrow
1
to
release the 2 upper side hooks.
Note:
Don't remove the cover in the direction of the arrow
2
.
Otherwise the hooks are broken.
(1) Remove the Side Cover (R).
(See 8.2.1. Side Cover (R))
(2) Remove the Side Cover (L).
(See 8.2.2. Side Cover (L))
(3) Pull the Rear Cover upward to unlock the cover and remove
it (2 arrows
1
).
Side Cover (L)
Bottom side
Hook
Side Cover (L)
Hook
1
Side Cover (L)
2
Rear Cover
1
1
26
8.2.4.
Exit Tray Assy
8.2.5.
Front Cover
(1) Slide the Exit Tray Assy (arrow
1
) until it goes.
(2) Remove the Exit Tray Assy while distorting it (arrow
2
).
Exit Tray Assy
2
1
2
(1) Remove the Side Cover (R).
(See 8.2.1. Side Cover (R))
(2) Remove the Side Cover (L).
(See 8.2.2. Side Cover (L))
(3) Remove the Exit Tray Assy.
(See 8.2.4. Exit Tray Assy)
(4) Push the Front Cover (2 arrows
1
) to the bottom side, and
then remove it (2 arrows
2
).
Front Cover
2
1
1
2
27
8.3.
Upper Chassis
8.3.1.
DFP Roller
8.3.2.
Top Cover
8.3.3.
PANEL Board
(1) Remove the DFP Roller Assy.
(See Appendix (Operating Manual P.45))
(2) Remove the rollers.
.
Reassembling Note:
Make sure to re-assemble the rollers between the ribs of the
pulleys.
pulleys.
NG
Rib
Rib
Rib
Good
DFP Roller
(1) Push the Door Open Button to open the ADF Door.
(2) While Pulling the Top Cover (arrow
(2) While Pulling the Top Cover (arrow
1
), pull the cover
(arrow
2
) and then (arrow
3
) to unlock the hooks.
(3) While Pulling the Top Cover (arrow
4
), pull the cover
(arrow
5
) and then (arrow
6
) to unlock the hooks.
3
5
:Hook
Top Cover
1
4
6
2
(1) Remove the Top Cover.
(See 8.3.2. Top Cover)
(2) Remove the 2 screws E and the Flat Cable.
(3) Remove the PANEL Board.
(3) Remove the PANEL Board.
Flat Cable
PANEL Board
E
E
28
8.3.4.
ULTRASONIC SENSOR (G) Board
8.3.5.
Free Roller
(1) Remove the Top Cover.
(See 8.3.2. Top Cover)
(2) Remove the 2 screws E and the Flat Cable.
(3) Remove the ULTRASONIC SENSOR (G) Board.
(3) Remove the ULTRASONIC SENSOR (G) Board.
Flat Cable
ULTRASONIC SENSOR(G) Board
E
(1) Remove the Top Cover.
(See 8.3.2. Top Cover)
(2) Remove the ULTRASONIC SENSOR (G) Board.
(See 8.3.4. ULTRASONIC SENSOR (G) Board)
(3) Remove 4 screws E.
(4) Remove the Reinforcement Plate.
(4) Remove the Reinforcement Plate.
(5) Remove 6 springs.
(6) Remove 4 Free Rollers with the shafts.
(6) Remove 4 Free Rollers with the shafts.
Reassembling Note:
Install the Free Rollers with the shaft so that the D-cut of the
shaft is visible and set the Free Roller springs.
shaft is visible and set the Free Roller springs.
(7) Remove the Free Roller from the Free Roller Sleeve.
E
Reinforcement Plate
ULTRASONIC SENSOR (G) Board
Free
Roller
Roller
Free
Roller
Roller
Free
Roller
Roller
Free
Roller
Roller
Free Roller
Shaft
Shaft
D-cut
Free Roller Spring 2
Free Roller Spring 2
Free Roller Spring
Free Roller Spring
Free Roller
Free Roller Sleeve
Free Roller
Click on the first or last page to see other KV-S1037 / KV-S1038 / KV-S1026C-M2 / KV-S1026C-J2 service manuals if exist.