JBL SUB 250P (serv.man2) EMC - CB Certificate ▷ View online
Page 8 of 54
Report No.: 11034065 001
TRF No. IEC60065K
or splashing and that no objects filled with liquids shall be placed on the apparatus (see subclause
5.4.1).
5.4.1).
•
The installation instructions provided with instructions of correct and safe installation and interconnection
of the apparatus in multimedia systems. (see subclause 5.4.1).
of the apparatus in multimedia systems. (see subclause 5.4.1).
•
Transformers are marked with following:
Transformer
Marking
T1, T2, CT1, DT1
Manufacturer and type (see
appended table 14)
appended table 14)
The product also marked with:
•
Fuse marking (See subclause 14.5.2.2): F1 120V: T6.3AL/ 250V; F1 230V: T4.0AL/250V.
•
(ISO 7000-0434) in manufacturer’s service documentation for each critical component.
•
(IEC 60417-5007) for "ON” of the switch (see subclause 5.4.2).
•
(IEC 60417-5008) for “OFF” of the switch (see subclause 5.4.2).
Page 9 of 54
Report No.: 11034065 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
3
General requirements
P
Safety class of the apparatus .................................. : See Test item particulars
P
4
General test conditions
P
4.1.4
Ventilation instructions require the use of the test
box
box
See Additional Information.
P
5
Marking and instructions
P
Comprehensible and easily discernible
The markings are permanent,
comprehensible and easily
discernible.
comprehensible and easily
discernible.
P
Permanent durability against water and petroleum
spirit
spirit
P
5.1
a) Identification, maker ............................................. : See Copy of marking plates
P
b) Model number or type reference .......................... : See Copy of marking plates
P
c) Class II symbol if applicable ................................ : See Copy of marking plates
P
d) Nature of supply .................................................... : See Copy of marking plates
P
e) Rated supply voltage ........................................... : See Copy of marking plates
P
f) Mains frequency if safety dependant ................... : See Copy of marking plates
P
g) Rated current or power consumption for
apparatus supplied by supply apparatus for general
use ............................................................................ :
apparatus supplied by supply apparatus for general
use ............................................................................ :
N/A
Measured current or power consumption ............... :
N/A
Deviation % (max 10%) ........................................... :
N/A
h) Rated current or power consumption for apparat-
us intended for connection to an a.c. mains supply . :
us intended for connection to an a.c. mains supply . :
See Copy of marking plates
P
Measured current or power consumption ............... : See appended table 7.1.
P
Measured current or power consumption for
Television set ........................................................... :
Television set ........................................................... :
N/A
Deviation % (max 10%) ........................................... :
P
5.2
a) Earth terminal
N/A
b) Hazardous live terminals
N/A
c) Markings on supply output terminals
N/A
5.3
a) Use of triangle with exclamation mark
Triangle with exclamation mark
is marked on each critical
component in circuit diagram.
is marked on each critical
component in circuit diagram.
P
b) marking on loudspeaker grille, IEC 60417-5036
N/A
5.4
Instructions for use
P
5.4.1
a) Mains powered equipment not exposed to
dripping or splashing. Warning concerning objects
filled with liquid, etc.
dripping or splashing. Warning concerning objects
filled with liquid, etc.
See Markings and
Instructions.
Instructions.
P
Page 10 of 54
Report No.: 11034065 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
b) Hazardous live terminals, instructions for wiring
N/A
c) Instructions for replacing lithium battery
N/A
d) Class I earth connection warning
N/A
e) Instructions for multimedia system connection
See Markings and
Instructions.
Instructions.
P
f) Special stability warning for attachment of the
apparatus to the floor/wall
apparatus to the floor/wall
N/A
g) Warning: battery exposure to heat
N/A
h) Warning: protective film on CRT face
N/A
5.4.2
a-b) Disconnect device: plug/coupler or all-pole
mains switch location, accessibility and markings
mains switch location, accessibility and markings
Inlet as the disconnect device.
P
c) Instructions for permanently connected equipment
N/A
Marking, signal lamps or similar for completely
disconnection from the mains
disconnection from the mains
Inlet as the disconnect device.
However, an all pole power
switch is used and marked
according to IEC 60417-
5007/5008.
However, an all pole power
switch is used and marked
according to IEC 60417-
5007/5008.
N/A
6
Hazardous radiation
N/A
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
N/A
Ionizing radiation under fault condition
N/A
6.2
Laser radiation, emission limits to IEC 60825-1:2007
................................................................................... :
................................................................................... :
N/A
Emission limits under fault conditions ..................... :
N/A
7
Heating under normal operating conditions
P
7.1
Temperature rises not exceeding specified values;
fuse links and other protective devices defeated
fuse links and other protective devices defeated
(see appended table)
P
7.1.1
Temperature rise of accessible parts
(see appended table)
P
7.1.2
Temperature rise of parts providing electrical
insulation
insulation
(see appended table)
P
7.1.3
Temperature rise of parts acting as a support or as a
mechanical barrier
mechanical barrier
N/A
7.1.4
Temperature rise of windings
(see appended table)
P
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
(see appended table)
P
7.2
Softening temperature of insulating material
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
supporting parts conductively connected to the
mains carrying a current > 0,2 A at least 150
o
C
Certified connector used. See
appended table 14.
appended table 14.
P
8
Constructional requirements with regard to the protection against electric
shock
shock
P
Page 11 of 54
Report No.: 11034065 001
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
8.1
Conductive parts covered by lacquer, paper,
untreated textile oxide films and beads etc.
considered to be bare
untreated textile oxide films and beads etc.
considered to be bare
Considered.
P
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
device, fuse-links or handling drawers etc.
N/A
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
hygroscopic material
No hygroscopic material is
used as insulation of
hazardous live parts.
used as insulation of
hazardous live parts.
Humidity treatment was
conducted under the required
relative humidity and following
conditioning period: 120h
conducted under the required
relative humidity and following
conditioning period: 120h
P
8.4
No risk of electric shock from accessible parts or
from parts rendered accessible following the
removal of a cover which can be removed by hand
from parts rendered accessible following the
removal of a cover which can be removed by hand
No risk of electric shock. See
8.6.
8.6.
P
8.5
Class I equipment
N/A
Basic insulation between hazardous live parts and
earthed accessible parts
earthed accessible parts
N/A
Resistors bridging basic insulation complying with
14.1 a)
14.1 a)
N/A
Capacitors bridging basic insulation complying with
14.2.1 a)
14.2.1 a)
N/A
Protective earthing terminal
N/A
8.6
Class II equipment and Class II constructions within
Class I equipment
Class I equipment
See below.
P
Double or reinforced insulation between hazardous
live parts and accessible parts
live parts and accessible parts
Hazardous live parts to
accessible parts are separated
by either reinforced or double
insulation.
accessible parts are separated
by either reinforced or double
insulation.
P
Components bridging double or reinforced insulation
complying with 14.1 a) or 14.3
complying with 14.1 a) or 14.3
Transformer (T1, T2, CT1 and
DT1) bridging reinforced or
double insulation complying
with 14.3.
DT1) bridging reinforced or
double insulation complying
with 14.3.
P
Basic insulation bridged by components complying
with 14.3.4.3.
with 14.3.4.3.
N/A
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.1 a)
bridged by a capacitor complying with 14.1 a)
N/A
Double or reinforced insulation being bridged with 2
capacitors in series complying with 14.2.1 a)
capacitors in series complying with 14.2.1 a)
N/A
Double or reinforced insulation being bridged with a
single capacitor complying with 14.2.1 b)
single capacitor complying with 14.2.1 b)
Y1-capacitor (CY1, CY2, CY3,
CY4) bridging Reinforced
insulation. See 14.2.1 b).
CY4) bridging Reinforced
insulation. See 14.2.1 b).
P
8.7
This clause is void
—
8.8
Basic or supplementary insulation > 0,4 mm (mm) :
Transformer (DT1 and T2)
bobbin thickness is 0.8mm
min.
bobbin thickness is 0.8mm
min.
P
Click on the first or last page to see other SUB 250P (serv.man2) service manuals if exist.