JBL SUB 250P (serv.man2) EMC - CB Certificate ▷ View online
Page 4 of 54
Report No.: 11034065 001
TRF No. IEC60065K
Copy of marking plate:
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
the respective NCBs that own these marks.
Page 5 of 54
Report No.: 11034065 001
TRF No. IEC60065K
Copy of marking plate:
The artwork below may be only a draft. The use of certification marks on a product must be authorized by
the respective NCBs that own these marks.
the respective NCBs that own these marks.
Page 6 of 54
Report No.: 11034065 001
TRF No. IEC60065K
Test item particulars ..................................................... :
Classification of installation and use ............................ : Class II, Portable equipment
Supply Connection ....................................................... : Non-detachable power cord
...................................................................................... :
Possible test case verdicts:
- test case does not apply to the test object ................. : N/A (Not Applicable)
- test object does meet the requirement ....................... : P (Pass)
- test object does not meet the requirement ................. : F (Fail)
Testing:
Date of receipt of test item ............................................ : August, 2013
Date (s) of performance of tests ................................... : August, 2013
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a
comma /
point is used as the decimal separator.
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has
been provided ................................................................ :
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has
been provided ................................................................ :
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) .............................. : DONGGUAN MEILOON ACOUSTIC
EQUIPMENTS CO., LTD.
NO. 77, Yuanlin Road, Feng Huang, Guang Ind.,
Estate Tangxia, Dongguan, Guangdong Province,
P.R. China
Estate Tangxia, Dongguan, Guangdong Province,
P.R. China
General product information:
Product Description
•
This equipment under test (EUT) is a powered subwoofer for the use in the scope of EN 60065.
•
Models SUB 250P/100 and SUB 250P are identical to each other and input voltage for these two
models is 100-120Vac.
models is 100-120Vac.
•
Models SUB 250P/230 and SUB 250P/230-C are identical to each other and input voltage for these
two models is 220-240Vac.
two models is 220-240Vac.
•
One power board used for all models. Jump (J2) is used to switch different input voltage (J2 short for
input 100-120Vac, J2 open for 220-240Vac) and is not user accessible.
input 100-120Vac, J2 open for 220-240Vac) and is not user accessible.
•
All components except subwoofer speaker are contained in an enclosure which consists of plastic
chassis (flammability rated V-1) and metal plate. No ventilation opening provided on this enclosure.
chassis (flammability rated V-1) and metal plate. No ventilation opening provided on this enclosure.
Engineering Considerations
•
The product was submitted and tested for use at the maximum ambient temperature (Tma)
Page 7 of 54
Report No.: 11034065 001
TRF No. IEC60065K
permitted by the manufacturer’s specification of: 35°C.
•
The product is intended to be used in environment of pollution degree 2.
•
The product is intended for use on the following power systems: TN.
•
The equipment disconnect device is considered to be: plug.
•
Following transformers are provided (See subclause 1.5.4): Transformer (T2, CT1, DT1 and T1) is an
isolating transformer.
isolating transformer.
•
Components bridging insulation other than functional:
Components
ID
Bridging location
Bridging insulation
Capacitor
CY1,
CY2,
CY3,
CY4
CY2,
CY3,
CY4
Primary-to-secondary
Double/Reinforced (see subclause
8.6)
8.6)
--
Primary-to-earth
Basic (see subclause 8.5)
CX1,
CX2
CX2
Across mains
conductors
conductors
--
Resistor
--
Primary-to-secondary
Double/Reinforced (see subclause
8.6)
8.6)
--
Primary-to-earth
Basic (see subclause 8.5)
R5, R8,
R5A,
R8A
R5A,
R8A
Across mains
conductors
conductors
--
VDR
--
Primary-to-earth
Basic
ZNR1
Across mains
conductors
conductors
--
•
Following solid insulation other than wiring insulation are provided (See subclause 8.8):
Type of Insulation
Type of solid insulation (distance through
insulation / thin sheet
Location
Layer or
thickness
Reinforced insulation
distance through insulation
Plastic
enclosure
2.5mm
•
Following devices were considered protective devices (See subclause 14.5): Fuse (F1).
Additional Information
•
The temperature measurements were carried out with the apparatus positioned in testing box in
accordance with subclause 4.1.4
accordance with subclause 4.1.4
•
The power supply unit used in the product is not a certified product. Hence, compliance has been
evaluated in this report.
evaluated in this report.
•
The equipment is for use in multimedia systems and was investigated additionally to IEC GUIDE
112.
112.
•
The Label in Copy of marking plate is a draft of an artwork pending approval by National Certification
Bodies and it shall not be affixed to products prior to such an approval.
Bodies and it shall not be affixed to products prior to such an approval.
•
The plug was investigated and found in compliance with applicable parts of corresponding plug
standard: EN 50075.
standard: EN 50075.
•
The connector part of the removable plug portion was investigated and found in compliance with
applicable parts of IEC 61984.
applicable parts of IEC 61984.
•
Some components are pre-certified, which have been evaluated according to the relevant
requirements of IEC 60065, are employed in this product. Their suitability of use has been checked
accordingly.
requirements of IEC 60065, are employed in this product. Their suitability of use has been checked
accordingly.
Markings and Instructions
•
The instructions for use provided information that stating the apparatus shall not be exposed to dripping
Click on the first or last page to see other SUB 250P (serv.man2) service manuals if exist.