JBL ON TIME 200ID EMC - CB Certificate ▷ View online
<12014165 001>
Page 60 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
16.3
Add: c) Flexible cords not complying with 16.1, used as
connection between the apparatus and other apparatus used
in combination with it, shall be marked VW-1.
connection between the apparatus and other apparatus used
in combination with it, shall be marked VW-1.
N/A
17.8
Expanded to include all cart/stand parts supplied by the
manufacturer, such as casters and brackets. Suitable
assembly instructions required. Add: “Relevant fixing means
are not required when installation is to be done by a skilled
person.”
manufacturer, such as casters and brackets. Suitable
assembly instructions required. Add: “Relevant fixing means
are not required when installation is to be done by a skilled
person.”
N/A
17.10
Add: Aluminum conductors used as internal wiring shall be
terminated by a method capable of being used in the
combination of metals involved at the connection point.
terminated by a method capable of being used in the
combination of metals involved at the connection point.
N/A
17.11
Add: An accessory shall be investigated to determine that: a)
The accessory, and the combination of the accessory and the
apparatus shall present no hazard in the sense of this
standard and b) The accessory is provided with installation
instructions.
The accessory, and the combination of the accessory and the
apparatus shall present no hazard in the sense of this
standard and b) The accessory is provided with installation
instructions.
N/A
17.11.1
Add: The installation of an accessory of a killed person shall
be such that: a) The mechanical positioning is accomplished
by means of tools normally available or by means of special
tools provided by the organization responsible for providing
the apparatus as part of the installation kit, and b) The
electrical connections are made by using existing terminals
and connections in the apparatus or the building wiring.
be such that: a) The mechanical positioning is accomplished
by means of tools normally available or by means of special
tools provided by the organization responsible for providing
the apparatus as part of the installation kit, and b) The
electrical connections are made by using existing terminals
and connections in the apparatus or the building wiring.
N/A
18
Modification: Non-intrinsically protected picture tubes shall
comply with 18.1, 18.2.2 and 18.3. Intrinsically protected
picture tubes shall comply with UL 1418 or UL 61965.
comply with 18.1, 18.2.2 and 18.3. Intrinsically protected
picture tubes shall comply with UL 1418 or UL 61965.
Add: “A bulb of a picture tube having a face diameter of
7.5cm or more shall be mounted in an enclosure. The
enclosure shall have no opening that exceeds 130 mm
7.5cm or more shall be mounted in an enclosure. The
enclosure shall have no opening that exceeds 130 mm
2
unless the minor dimension of the opening is 10 mm or less.”
No picture tube provided.
N/A
<12014165 001>
Page 61 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
18.1
All tubes shall be mounted such that the enclosure of the
apparatus protects the tube against the effects of implosion.
Delete reference to clause 18.2.
apparatus protects the tube against the effects of implosion.
Delete reference to clause 18.2.
18.2, 18.2.1, and 18.2.3 are deleted..19-Add reference to
19.2.1. The test of 19.3 is conducted on 1) apparatus with
direct view CRT with 48cm
19.2.1. The test of 19.3 is conducted on 1) apparatus with
direct view CRT with 48cm
diagonal min., 2) apparatus, other than a speaker, with a
mass greater than 47kg, and 3) apparatus, other than a
speaker, with a mass or 25kg or greater and height of 1 m or
more. The tests in 19.1, 19.2 and 19.3 shall not cause the
apparatus to overturn. During the test of 19.2.1, the apparatus
shall not slide.
mass greater than 47kg, and 3) apparatus, other than a
speaker, with a mass or 25kg or greater and height of 1 m or
more. The tests in 19.1, 19.2 and 19.3 shall not cause the
apparatus to overturn. During the test of 19.2.1, the apparatus
shall not slide.
N/A
19.2.1
Add: Slide test requirements.
P
19.3
Replace by Horizontal force stability test requirements.
P
Table 20
Add: “or equipment rack mounting”.
P
20.1a
Delete
N/A
20.1b
Replace “IEC 60707” with “UL 94”
Add: “-parts such as protection TV lenses, loudspeaker parts,
external accessories, and fibrous materials less than 0.25mm
thick.”
external accessories, and fibrous materials less than 0.25mm
thick.”
(see appended table)
P
20.1.2
Revise text to read: “Sleeving, extruded tubing and insulation
on wiring shall be rated VW-1 under following conditions: a)
wiring located in a circuit that is considered a potential ignition
source” or b) wiring not located in a circuit that is a potential
ignition source but is in contact with wiring located in a circuit
that is a potential ignition source. “Tape should be flame
retardant.”
on wiring shall be rated VW-1 under following conditions: a)
wiring located in a circuit that is considered a potential ignition
source” or b) wiring not located in a circuit that is a potential
ignition source but is in contact with wiring located in a circuit
that is a potential ignition source. “Tape should be flame
retardant.”
Delete Note and add: “Tape in contact with parts of circuits
that are potential ignition source shall be flame retardant.”
that are potential ignition source shall be flame retardant.”
(see appended table)
P
<12014165 001>
Page 62 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
20.1.3
Replace 1st paragraph with: “Base material of printed wiring
boards, or which the available power as the connection
exceeds 15W or the operating voltage exceeds 50V a.c. or
d.c. under normal operating conditions, shall be of
flammability category V-1 or better according to UL 94.”
boards, or which the available power as the connection
exceeds 15W or the operating voltage exceeds 50V a.c. or
d.c. under normal operating conditions, shall be of
flammability category V-1 or better according to UL 94.”
In 2nd paragraph replace “IEC 60707” with “UL 94” and
remove exception for printed boards housed in metal
enclosures.
remove exception for printed boards housed in metal
enclosures.
In 3rd paragraph replace “IEC 60707” with “UL 94” and delete
option to use Clause G.1 of Annex G.
option to use Clause G.1 of Annex G.
(see appended table)
P
20.1.4
Replace with: components and parts shall comply with the
relevant flammability category according to UL 94 as specified
in Table 21. Delete all other text.
relevant flammability category according to UL 94 as specified
in Table 21. Delete all other text.
(see appended table)
P
20.1.4
Add: “Component power supplies complying with the
construction and test requirements of UL 1310, UL 1950
Third Edition, or UL 60950 are considered to fulfill the test
requirements on the clause.”
construction and test requirements of UL 1310, UL 1950
Third Edition, or UL 60950 are considered to fulfill the test
requirements on the clause.”
Table 21 – Replace complete table with new table for
“Flammability categories for components and parts.”
“Flammability categories for components and parts.”
N/A
20.2.1
Modification: 1st paragraph: “Fire enclosure required for 1)
circuits and components where the available power exceeds
15W, 2) inductors and windings conductively connected to the
mains and 3) high-voltage products. The fire enclosure shall
comply with the flammability requirements of Table 22
according to UL 94 and 746C. 2nd, 3rd, and 4th paragraphs
are deleted.
circuits and components where the available power exceeds
15W, 2) inductors and windings conductively connected to the
mains and 3) high-voltage products. The fire enclosure shall
comply with the flammability requirements of Table 22
according to UL 94 and 746C. 2nd, 3rd, and 4th paragraphs
are deleted.
In 5th paragraph replace “IEC 60707 or clause G.1 of Annex
G” with “UL 94 or UL 746C.”
G” with “UL 94 or UL 746C.”
Table 22 – Add “Flammability categories for fire enclosures.”
N/A
<12014165 001>
Page 63 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
20.2.2
20.2.3 – Modification: Outer enclosures shall have a minimum
flammability rating of HB, per UL 94, when an internal fire
enclosure is provided.
flammability rating of HB, per UL 94, when an internal fire
enclosure is provided.
Modifications to figures:
Fig 14 – Illustrates the articulated finger probe.
Fig 15 – Illustrates the shock hazard marking and associated
graphical symbols.
graphical symbols.
Fig 16 – Illustrates the shock hazard graphical symbol.
Fig 17 – Illustrates the portable cart marking.
Fig 18 – High voltage spacings graph.
Fig 19 – Class 105 insulation aging temperature graph.
Fig 20 – Flowchart for horizontal force test.
Annex A – Modification: Apparatus intended for outdoor use
or wet locations has any of the following attributes: a)
provided with a means to make it transportable, b) has a
mass less than 35kg, c) can be battery operated, d)
associated literature states or implies such use
or wet locations has any of the following attributes: a)
provided with a means to make it transportable, b) has a
mass less than 35kg, c) can be battery operated, d)
associated literature states or implies such use
Add: Apparatus in a), b), or c) above is not considered for
outdoor use or in wet locations if marked as specified in
5.4..A.5, A.5.4.1 are deleted.
outdoor use or in wet locations if marked as specified in
5.4..A.5, A.5.4.1 are deleted.
A9.1.1 – Add: Touch current test shall be conducted after the
water spray test described in A.11.1.1 and the touch current
shall not be more than 0.5MIU when the open-circuit potential
between any accessible part and earth or any other
accessible part is more than 21.2V peak.
water spray test described in A.11.1.1 and the touch current
shall not be more than 0.5MIU when the open-circuit potential
between any accessible part and earth or any other
accessible part is more than 21.2V peak.
A.10, A10.2, A10.2.1, and A.10.2.2 are deleted.
A.11.1.1 – Add: Apparatus shall be subjected to the water
spray test according to UL 1571.
spray test according to UL 1571.
N/A
Click on the first or last page to see other ON TIME 200ID service manuals if exist.