JBL ON TIME 200ID EMC - CB Certificate ▷ View online
<12014165 001>
Page 52 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
APPENDIX US National Differences according to CB Bulletin No. 109A, December 2005 (UL 60065)
(IEC Publication 60065 7th edition, 2001)
P
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N=Not applicable. Placed in the column to the right.
1.1.1
Scope clarification:
The standard also covers commercial and professional
apparatus; professional apparatus may also be investigated
using UL 1419. Projection apparatus is not covered.
Household games, household gaming and scoring machines,
satellite receiver antenna positioners are covered by this
standard but commercial games and commercial gaming and
scoring machines, and other types of antenna positioners are
covered by other standard.
apparatus; professional apparatus may also be investigated
using UL 1419. Projection apparatus is not covered.
Household games, household gaming and scoring machines,
satellite receiver antenna positioners are covered by this
standard but commercial games and commercial gaming and
scoring machines, and other types of antenna positioners are
covered by other standard.
Add: Mains connected apparatus intended for field installation
requires compliance with the National Electrical Code, ANSI,
NFPA 70.
requires compliance with the National Electrical Code, ANSI,
NFPA 70.
Considered.
P
1.1.3
Protection against splashing water replaced with apparatus
intended for outdoor use (See Annex A).
intended for outdoor use (See Annex A).
N/A
1.1.5
Add: Some equipment covered by these requirements may
also be required to comply with applicable requirements in
other standards
also be required to comply with applicable requirements in
other standards
Added
P
1.2
Add references to ANSI, ASTM and UL standards.
Added
P
4.2.1
Add Note: In the U.S. the RATED SUPPLY VOLTAGE for
single-phase apparatus is assumed to be 120 V or 120/240 V.
single-phase apparatus is assumed to be 120 V or 120/240 V.
Input voltage is 100-240Vac
P
4.2.4
Revision to sub-clause a): Minimum audio output is not less
than 0.5 W per channel unless the maximum audio output is
less than 0.5 W per channel.
than 0.5 W per channel unless the maximum audio output is
less than 0.5 W per channel.
No audio output provided.
N/A
4.2.4.1
Add: “An apparatus with multiple modes of operation, multiple
signal input sources, or both, is to be operated using each
mode of operation or signal input source separately, or in
combination, according to the manufacturer’s instructions to
produce the maximum power input”.
signal input sources, or both, is to be operated using each
mode of operation or signal input source separately, or in
combination, according to the manufacturer’s instructions to
produce the maximum power input”.
Table 2: External supply sources are assumed to be capable
of delivering 30 A, unless otherwise specified (no-load voltage
and internal resistance values in the Table are modified).
of delivering 30 A, unless otherwise specified (no-load voltage
and internal resistance values in the Table are modified).
Not such equipment
N/A
4.3.4
PTC thermistors may also comply with UL 1434.
No PTC provided.
N/A
<12014165 001>
Page 53 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
5.1
Add: Component power supplies and adapters complying with
the construction and test requirements of UL 1310, UL 1950,
or UL 60950 fulfill the requirements of items “a” through “i” of
this clause.
the construction and test requirements of UL 1310, UL 1950,
or UL 60950 fulfill the requirements of items “a” through “i” of
this clause.
Added
N/A
5.1f
Add: Rated frequency is required on all apparatus.
50/60Hz
P
5.1g
Add: Rated current or power required on all apparatus.
1,5A
P
5.1j
Add: Date of Manufacture marking required on all apparatus. Date of manufacture show on
outer enclosure.
P
5.1k
Add: Manufacturing identification marking required.
Only one factory.
N/A
5.1l
Add: Combination of two graphical symbols and
supplementary marking is required.
supplementary marking is required.
The enclosure of EUT is
sealed by ultrasonic welding,
No possibility for user to open
by tools.
sealed by ultrasonic welding,
No possibility for user to open
by tools.
N/A
5.1m
Add: Equipment rack marking required for audio/video
systems.
systems.
No rack provided.
N/A
5.1n
Add: Units having leakage current levels greater than 0.75
MIU and equal to or less than 3.5 MIU must be marked with a
high leakage current marking.
MIU and equal to or less than 3.5 MIU must be marked with a
high leakage current marking.
Leakage current no less than
0.75MIU, for details refer to
clause 9.1.
0.75MIU, for details refer to
clause 9.1.
N/A
5.2c
Modification: Output terminals must be marked with voltage,
frequency and current or power; output terminals installed or
interconnected in the field must be marked with the class of
wiring.
frequency and current or power; output terminals installed or
interconnected in the field must be marked with the class of
wiring.
The nominal output voltage
and current are marked on
the name label.
and current are marked on
the name label.
P
5.2d
Add: Audio output connections shall be marked “Class 1
Wiring”, “Class 2 Wiring” or “Class 3 Wiring”. Operation
manual shall discuss risks and proper connecting and
insulation techniques when connecting a speaker.
Wiring”, “Class 2 Wiring” or “Class 3 Wiring”. Operation
manual shall discuss risks and proper connecting and
insulation techniques when connecting a speaker.
No audio output connections
provided.
provided.
N/A
5.3
Add: “An explanation and illustration of safety related
graphical symbols used on the apparatus shall be included in
the owner’s instructions preceding any operating instructions.
graphical symbols used on the apparatus shall be included in
the owner’s instructions preceding any operating instructions.
No such symbols.
N/A
5.4
Add: Important Safety Instructions are to be packed with each
apparatus and shall be verbatim.
apparatus and shall be verbatim.
P
5.4.1
Warning about Outdoor Use is required.
Indoor use logo was added in
the label and warning added
in the user manual
the label and warning added
in the user manual
P
5.4.3
Add: When apparatus contains instructions for use by service
personnel the instructions are separate in format and
preceded by a precautionary warning statement.
personnel the instructions are separate in format and
preceded by a precautionary warning statement.
Not use by service personnel
N/A
<12014165 001>
Page 54 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
6.1
Starting from second paragraph replace all by: ”Compliance is
checked in accordance with the requirements in the U.S.
Code of Federal Regulation, Title 21, Chapter 1, Subchapter
J, Sections 1010.2, 1010.3 and 1020.10 by measuring the
radiation produced by the apparatus employing a design
center chassis.”
checked in accordance with the requirements in the U.S.
Code of Federal Regulation, Title 21, Chapter 1, Subchapter
J, Sections 1010.2, 1010.3 and 1020.10 by measuring the
radiation produced by the apparatus employing a design
center chassis.”
No radiation
N/A
6.2
Starting from second paragraph replace all by: “Apparatus
shall be classified and labeled in accordance with the Code of
Federal Regulations, Title 21, Chapter 1, Subchapter J,
Sections 1010.2, 1010.3, 1040.10 and 1040.11.”
shall be classified and labeled in accordance with the Code of
Federal Regulations, Title 21, Chapter 1, Subchapter J,
Sections 1010.2, 1010.3, 1040.10 and 1040.11.”
No ionizing radiation or laser
inside the equipment.
inside the equipment.
N/A
6.2.2
Deleted
Table 3: Temperature limits added for various classes of
insulation systems.
insulation systems.
Add to Note a): “Materials rated in accordance with UL 746B
may be used at their rated higher temperature.”.7.2 – Add: A
material temperature rating can be accepted in lieu of the
softening temperature. The softening test need not be
performed on materials used in UL Listed or Recognized
parts.
may be used at their rated higher temperature.”.7.2 – Add: A
material temperature rating can be accepted in lieu of the
softening temperature. The softening test need not be
performed on materials used in UL Listed or Recognized
parts.
Deleted and added.
N/A
8.1
Add: “A metal part that is not inherently resistant to corrosion
shall be protected against corrosion when corrosion of that
part is capable of contributing to or resulting in a risk of fire,
shock, or injury to persons.”
shall be protected against corrosion when corrosion of that
part is capable of contributing to or resulting in a risk of fire,
shock, or injury to persons.”
Added.
P
8.9.1
Add: “Sleeving, tape, tubing, and wire insulation are suitable
for the conditions of use, such as voltage and temperature,
and comply with UL 224, UL 510, and UL 1441, as
applicable.”
for the conditions of use, such as voltage and temperature,
and comply with UL 224, UL 510, and UL 1441, as
applicable.”
UL approved material used
P
8.10
Add: “Component power supplies and their internal insulation
complying with the construction and test requirements of UL
1310, UL 1950 Third Edition, or UL 60950 are considered to
fulfill the test requirements on the clause.”
complying with the construction and test requirements of UL
1310, UL 1950 Third Edition, or UL 60950 are considered to
fulfill the test requirements on the clause.”
Considered.
N/A
8.12
Modification: Conductors and internal wiring connecting mains
socket-outlets shall comply with the wire size requirements in
clause 16.2 based on the marked rating of the outlet but shall
not be less than 18 AWG.
socket-outlets shall comply with the wire size requirements in
clause 16.2 based on the marked rating of the outlet but shall
not be less than 18 AWG.
No socket-outlet
N/A
8.17
As an option, winding wire insulation may comply with the
requirements in UL Subject 2353.
requirements in UL Subject 2353.
Added.
P
8.19.1
Modification: An all-pole switch or circuit breaker is not
required to have contact separation of 3 mm.
required to have contact separation of 3 mm.
No switches provided.
N/A
<12014165 001>
Page 55 of 73
National Deviation
Clause
Requirement – Test
Result - Remark
Verdict
US National Difference according to CB Bulletin No. 109A, December 2005
8.22
Add: “Printed wiring boards involved with the risk of electric
shock shall comply with the requirements in UL 796.”
shock shall comply with the requirements in UL 796.”
UL approved PCB is used.
P
9.1.1.1
Replace: For Class I apparatus the r.m.s. TOUCH-CURRENT
to earth shall not be more than 3.5 MIU.
to earth shall not be more than 3.5 MIU.
Class II equipment.
N/A
9.1.1.1a
2nd dash replaced by: “For audio signals of professional and
commercial apparatus, 120 Vrms.”
commercial apparatus, 120 Vrms.”
3rd dash replaced by: ”For audio signals other than
professional and commercial apparatus, 71 Vrms.”
professional and commercial apparatus, 71 Vrms.”
No such signal.
N/A
9.1.1.1b
Modification: Touch current shall comply with the American
National Standard for Leakage Current for Appliances, ANSI
C101 and not exceed 0.5MIU for Class II Delete Note 2.
National Standard for Leakage Current for Appliances, ANSI
C101 and not exceed 0.5MIU for Class II Delete Note 2.
L/N to Enclosure: 0,17MIU;
L/N to output terminal:
0,08MIU
L/N to output terminal:
0,08MIU
P
9.1.1.2
UL articulated finger replaces IEC 61032 test probe B. Delete
3rd paragraph.
3rd paragraph.
Table 5 – Add Note 1: “With respect to mains voltages in the
range of 105-130 V(rms), the test voltages are considered to
be 1414 V peak for basic and supplementary insulation and
2828 V peak for reinforced insulation.”
range of 105-130 V(rms), the test voltages are considered to
be 1414 V peak for basic and supplementary insulation and
2828 V peak for reinforced insulation.”
Considered
P
11
Add: “Component power supplies and their power
transformers complying with the construction and test
requirements of UL 1310, UL 1950 Third Edition, or UL 60950
are considered to fulfill the test requirements on the clause.”
transformers complying with the construction and test
requirements of UL 1310, UL 1950 Third Edition, or UL 60950
are considered to fulfill the test requirements on the clause.”
N/A
11.1
Modification: The permissible touch current for terminal
contacts has been increased to twice the value given in
9.1.1.1.
contacts has been increased to twice the value given in
9.1.1.1.
L/N to Enclosure: 0,17MIU;
L/N to output terminal:
0,08MIU
L/N to output terminal:
0,08MIU
P
11.2.1
Modification: Additional fuse testing not required if the
temperature is limited by fuses.
temperature is limited by fuses.
Considered
P
12
Add: “Component power supply adaptors and their
enclosures complying with the construction and test
requirements of UL 1310, UL 1950 Third Edition, or UL
60950 are considered to fulfill the test requirements on the
clause.”
enclosures complying with the construction and test
requirements of UL 1310, UL 1950 Third Edition, or UL
60950 are considered to fulfill the test requirements on the
clause.”
N/A
12.1.3
Delete the first tow paragraphs. Impact test uses the 50mm
steel sphere only.
steel sphere only.
Table 6 – Replace title with “Apparatus impact test.” Table 6
modified to provide impact test criteria detailing impact
location, impact energy and additional pass/fail results.”
modified to provide impact test criteria detailing impact
location, impact energy and additional pass/fail results.”
Considered
P
Click on the first or last page to see other ON TIME 200ID service manuals if exist.