Sony HDR-FX1000 / HDR-FX1000E (serv.man3) Service Manual ▷ View online
6-36
HDR-FX1000/FX1000E_ADJ
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
99
Check the data is “00”.
3
6
02
Check the data is “00”.
4
6
9B
Check the bit value of bit2 is
“0”. (Note 4)
“0”. (Note 4)
5
6
9B
Check the bit value of bit3 is
“0”. (Note 4)
“0”. (Note 4)
6
6
07
Check the data is “04”.
7
6
15
A0
8
6
61
01
9
Wait for 3 seconds.
10
6
40
01
11
6
41
01
12
6
C9
10
13
6
CA
04
14
6
D0
35
15
6
01
61
Press PAUSE (Write) button.
(Note 5)
(Note 5)
16
6
02
Check the data changes to
“01”.
“01”.
17
6
0C
Check the data is “00”.
Note 4:
For the bit values, refer to “6-4. SERVICE MODE”, “4-
4. 3. Bit value discrimination”.
4. 3. Bit value discrimination”.
Note 5:
The adjustment data will be automatically input to page:
6F, address: B0 to B7, A8 to AF.
6F, address: B0 to B7, A8 to AF.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
C9
00
3
6
CA
00
4
6
40
00
5
6
41
00
6
6
15
00
7
6
61
00
8
0
01
00
17. Color Reproduction Adjustment
RadarW
RadarW
RadarW
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Measurement Point
Adjusting remote commander
Measuring Instrument
Adjustment Page
6F
Adjustment Address
B0 to B7 (HD),
A8 to AF (SD)
A8 to AF (SD)
Specified Value
Data of page: 6 address: 0C is “00”
Note 1:
Perform “Auto White Balance Standard Data Input” be-
fore this adjustment.
fore this adjustment.
Note 2:
If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
6-37
HDR-FX1000/FX1000E_ADJ
18. Color Reproduction Check (Outdoor)
RadarW
RadarW
RadarW
Subject
Color bar chart (Color reproduction
adjustment frame)
adjustment frame)
Filter
Filter C14 for color temperature
correction
correction
Measurement Point
Adjusting remote commander
Measuring Instrument
Specified Value
Data of page: 6, address: 0C is “00”
Note 1:
Perform “Color Reproduction Adjustment” before this
adjustment.
adjustment.
Note 2:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ...................................................................... OFF
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
Checking method:
Order Page Address Data
Procedure
1
Place the C14 filter on the
lens.
lens.
2
0
01
01
3
6
99
Check the data is “00”.
4
6
02
Check the data is “00”.
5
6
9B
Check the bit value of bit2 is
“0”. (Note 3)
“0”. (Note 3)
6
6
9B
Check the bit value of bit3 is
“0”. (Note 3)
“0”. (Note 3)
7
6
07
Check the data is “04”.
8
6
15
A0
9
6
61
01
10
Wait for 3 seconds.
11
6
40
01
12
6
41
01
13
6
C9
10
14
6
CA
04
15
6
D0
35
16
6
01
3D
Press PAUSE (Write) button.
17
6
02
Check the data changes to
“01”.
“01”.
18
6
0C
Check the data is “00”.
Note 3:
For the bit values, refer to “6-4. SERVICE MODE”, “4-
4. 3. Bit value discrimination”.
4. 3. Bit value discrimination”.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
C9
00
3
6
CA
00
4
6
40
00
5
6
41
00
6
6
15
00
7
6
61
00
8
0
01
00
9
Remove the C14 filter on the
lens.
lens.
6-38
HDR-FX1000/FX1000E_ADJ
20. Auto White Balance Adjustment (ND1)
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility
will be poor.
If it is not correct, auto white balance and color reproducibility
will be poor.
Subject
Clear chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Filter
Filter C14 for color temperature
correction
correction
Adjustment Page
6F
Adjustment Address
9C to 9F
Note 1:
Perform “Auto White Balance Standard Data Input” be-
fore this adjustment.
fore this adjustment.
Note 2:
If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 1
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 1
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
Adjusting method:
Order Page Address Data
Procedure
1
Place the C14 filter on the
lens.
lens.
2
0
01
01
3
6
99
Check the data is “01”.
4
6
02
Check the data is “00”.
5
6
07
Check the data is “04”.
6
6
40
01
7
6
41
01
8
6
01
81
Press PAUSE (Write) button.
(Note 4)
(Note 4)
9
6
02
Check the data changes to
“01”.
“01”.
Note 4:
The adjustment data will be automatically input to page:
6F, address: 9C to 9F.
6F, address: 9C to 9F.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
40
00
3
6
41
00
4
0
01
00
5
Remove the C14 filter on the
lens.
lens.
19. Auto White Balance Standard Data Input
(ND1)
RadarW
RadarW
RadarW
Adjust the white balance reference at 3200K, and adjust the nor-
mal coefficient of the light value.
mal coefficient of the light value.
Subject
Clear chart (Color reproduction
adjustment frame)
adjustment frame)
Measurement Point
Adjusting remote commander
Measuring Instrument
Adjustment Page
6F
Adjustment Address
8C to 8F
Specified Value
Data of page: 6 address: 0C is “00”
Note 1:
Perform “Auto White Balance Standard Data Input” be-
fore this adjustment.
fore this adjustment.
Note 2:
If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 1
3) D.EXTENDER (Menu setting) ....................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 1
3) D.EXTENDER (Menu setting) ....................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
99
Check the data is “01”.
3
6
02
Check the data is “00”.
4
6
07
Check the data is “04”.
5
6
61
01
6
Wait for 3 seconds.
7
6
40
01
8
6
41
01
9
6
01
0B
Press PAUSE (Write) button.
(Note 4)
(Note 4)
10
6
02
Check the data changes to
“01”.
“01”.
11
6
0C
Check the data is “00”.
Note 4:
The adjustment data will be automatically input to page:
6F, address: 8C to 8F.
6F, address: 8C to 8F.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
40
00
3
6
41
00
4
6
61
00
5
0
01
00
6-39
HDR-FX1000/FX1000E_ADJ
21. Auto White Balance Check (ND1)
RadarW
RadarW
RadarW
RadarW
RadarW
Subject
Clear chart (Color reproduction
adjustment frame)
adjustment frame)
Filter
ND filter 1.0, 0.4 and 0.1
Measurement Point
Adjusting remote commander
Measuring Instrument
Specified Value
Data of page: 6, address: 0C is “00”
Note 1:
Perform “Auto White Balance Standard Data Input
(ND1)”, “LV Standard Data Input” and “Auto White Bal-
ance Adjustment (ND1)” before this adjustment.
(ND1)”, “LV Standard Data Input” and “Auto White Bal-
ance Adjustment (ND1)” before this adjustment.
Note 2:
Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
If not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Switch setting
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 1
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
1) POWER ......................................................... CAMERA mode
2) ND FILTER ............................................................................ 1
3) D. EXTENDER (Menu setting) ...................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) REC FORMAT (Menu setting) ............................. HDV1080i
Checking method:
Order Page Address Data
Procedure
1
0
01
01
2
6
9B
Check the bit value of bit2 is
“0”. (Note 3)
“0”. (Note 3)
3
6
99
Check the data is “01”.
4
6
07
Check the data is “04”.
5
6
61
01
6
Wait for 3 seconds.
7
6
40
01
8
6
41
01
9
6
CA
85
10
6
C9
10
OUTDOOR white balance check
11
6
01
4F
Press PAUSE (Write) button.
12
6
02
Check the data changes to
“01”.
“01”.
13
6
0C
Check the data is “00”.
14
6
01
00
Press PAUSE (Write) button.
INDOOR white balance check
15
6
01
0F
Press PAUSE (Write) button.
16
6
02
Check the data changes to
“01”.
“01”.
17
6
0C
Check the data is “00”.
18
6
01
00
Press PAUSE (Write) button.
19
6
61
00
20
Wait for 3 seconds.
Order Page Address Data
Procedure
InOut check
21
Place the ND filter 1.5 (1.0
+0.4 + 0.1) on the lens.
+0.4 + 0.1) on the lens.
22
6
C9
11
23
6
01
4B
Press PAUSE (Write) button.
24
6
02
Check the data changes to
“01”.
“01”.
25
6
0C
Check the data is “00”.
26
6
01
00
Press PAUSE (Write) button.
27
Remove the ND filter 1.5
(1.0 + 0.4 + 0.1) on the lens.
(1.0 + 0.4 + 0.1) on the lens.
Note 3:
For the bit values, refer to “6-4. SERVICE MODE”, “4-
4. 3. Bit value discrimination”.
4. 3. Bit value discrimination”.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
C9
00
2
6
CA
00
3
6
40
00
4
6
41
00
5
0
01
00
Click on the first or last page to see other HDR-FX1000 / HDR-FX1000E (serv.man3) service manuals if exist.