Sony HDR-FX1000 / HDR-FX1000E (serv.man3) Service Manual ▷ View online
6-48
HDR-FX1000/FX1000E_ADJ
34-1. Angular Velocity Sensor Sensitivity Adjustment (1)
Adjustment Page
7F (Note 1)
Adjustment Address
20
Note 1:
If reading/writing data on pages 7F, set data: 07 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 7F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: F. By this data set-
ting, the pages 7F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
The PITCH sensor (SE8501 of GY-014 board) sensitiv-
ity is labeled only the repair parts.
ity is labeled only the repair parts.
Preparation
1) Read the PITCH sensor (SE8501 of GY-014 board) sensitivity
1) Read the PITCH sensor (SE8501 of GY-014 board) sensitivity
written on repair parts, and named this as S
20
.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
07
3
Calculate D
20
’ using
following equations.
(decimal calculation)
(Note 3)
D
(decimal calculation)
(Note 3)
D
20
’ = 129
×
(60/S
20
)
4
Convert D
20
’ to a hexadeci-
mal number, and obtain D
20
.
(Note 4)
5
F
20
D
20
Press PAUSE (Write) button.
(7F)
6
0
10
00
Note 3:
S
20
is read in “Preparation”.
Note 4:
Refer to table 6-4-1. “Hexadecimal-decimal conversion
table”.
table”.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
0
01
00
2
Check that the steady shot
function operates normally.
function operates normally.
34-2. Angular Velocity Sensor Sensitivity Adjustment (2)
Adjustment Page
7F (Note 1)
Adjustment Address
21
Note 1:
If reading/writing data on pages 7F, set data: 07 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 7F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: F. By this data set-
ting, the pages 7F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
The YAW sensor (SE8502 of GY-014 board) sensitivity
is labeled only the repair parts.
is labeled only the repair parts.
Preparation
1) Read the YAW sensor (SE8502 of GY-014 board) sensitivity
1) Read the YAW sensor (SE8502 of GY-014 board) sensitivity
written on repair parts, and named this as S
21
.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
07
3
Calculate D
21
’ using
following equations.
(decimal calculation)
(Note 3)
D
(decimal calculation)
(Note 3)
D
21
’ = 128
×
(60/S
21
)
4
Convert D
21
’ to a hexadeci-
mal number, and obtain D
21
.
(Note 4)
5
F
21
D
21
Press PAUSE (Write) button.
(7F)
6
0
10
00
Note 3:
S
21
is read in “Preparation”.
Note 4:
Refer to table 6-4-1. “Hexadecimal-decimal conversion
table”.
table”.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
0
01
00
2
Check that the steady shot
function operates normally.
function operates normally.
6-49
HDR-FX1000/FX1000E_ADJ
1-4.
ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENTS
ADJUSTMENTS
Before perform the viewfinder system adjustments, check the data
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
Note 1:
Taken an extreme care not to destroy the liquid crystal
display module by static electricity when replacing it.
display module by static electricity when replacing it.
1.
EVF Gain Adjustment (VF-178 board)
RadarW
RadarW
RadarW
This adjustment does the following items automatically.
RGB Amp Adjustment
Contrast Adjustment
Contrast Adjustment
Mode
VTR stop (VCR mode)
Signal
No signal
Adjustment Page
C
Adjustment Address
A9 to AE
Specified value
The data of page :3, address: 03 is
“00”
“00”
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
0
10
01
4
8
AF
Set the bit value of bit1 is
(18)
“1”, and press PAUSE
(Write) button. (Note 2)
(Write) button. (Note 2)
5
8
AC
04
Press PAUSE (Write) button.
(18)
6
8
A3
44
Press PAUSE (Write) button.
(18)
7
0
10
00
8
3
03
FF
Press PAUSE (Write) button.
9
3
01
6B
Press PAUSE (Write) button.
(Note 3)
(Note 3)
10
3
03
Check the data is "00".
(Note 4)
(Note 4)
11
3
70
10
Press PAUSE (Write) button.
12
3
70
Check the data changes to
“11”.
“11”.
13
0
01
00
Note 2:
For the bit values, refer to “6-4. SERVICE MODE”, “4-
4. 3. Bit value discrimination”.
4. 3. Bit value discrimination”.
Note 3:
The adjustment data will be automatically input to page:
C, address: A9 to AE.
C, address: A9 to AE.
Note 4:
If the data is other than “00”, adjustment has errors. Con-
tents of error is written into page: 3, address: 03. See the
following table.
tents of error is written into page: 3, address: 03. See the
following table.
Data of page: 3, address: 03
Contents of error
81
EVF_G adjustment error
82
EVF_R adjustment error
83
EVF_B adjustment error.
6-50
HDR-FX1000/FX1000E_ADJ
1.
PANEL Gain Adjustment (PD-372 board)
RadarW
RadarW
RadarW
This adjustment does the following items automatically.
RGB Amp Adjustment
Contrast Adjustment
Contrast Adjustment
Mode
VTR stop (VCR mode)
Signal
No signal
Adjustment Page
C
Adjustment Address
A6 to A8, AF to B1
Specified value
The data of page: 3, address: 03 is
“00”
“00”
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Switch setting:
VIDEO OUT .......................................................................... LCD
(Page: 7, address: 4F, Bit1 = 0)
VIDEO OUT .......................................................................... LCD
(Page: 7, address: 4F, Bit1 = 0)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
0
10
01
4
8
AF
Set the bit value of bit1 is
(18)
“1”, and press PAUSE
(Write) button. (Note 2)
(Write) button. (Note 2)
5
8
AC
04
Press PAUSE (Write) button.
(18)
6
8
A3
44
Press PAUSE (Write) button.
(18)
7
0
10
00
8
3
03
FF
Press PAUSE (Write) button.
9
3
01
6A
Press PAUSE (Write) button.
(Note 3)
(Note 3)
10
3
03
Check the data is "00".
(Note 4)
(Note 4)
11
3
70
10
Press PAUSE (Write) button.
12
3
70
Check the data changes to
“11”.
“11”.
13
0
01
00
Note 2:
For the bit values, refer to “6-4. SERVICE MODE”, “4-
4. 3. Bit value discrimination”.
4. 3. Bit value discrimination”.
Note 3:
The adjustment data will be automatically input to page:
C, address: A6 to A8, AF to B1.
C, address: A6 to A8, AF to B1.
Note 4:
If the data is other than “00”, adjustment has errors. Con-
tents of error is written into page: 3, address: 03. See the
following table.
tents of error is written into page: 3, address: 03. See the
following table.
Data of page: 3, address: 03
Contents of error
01
PANEL_G adjustment error
02
PANEL_R adjustment error
03
PANEL_B adjustment error
1-5.
LCD SYSTEM ADJUSTMENTS
Before perform the LCD system adjustments, check that the data
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
Note 1:
Taken an extreme care not to destroy the liquid crystal
display module by static electricity when replacing it.
display module by static electricity when replacing it.
Note 2:
Set the “LCD BRIGHT”, “LCD COLOR” to the center
with the menu settings of the LCD panel.
with the menu settings of the LCD panel.
Note 3:
Open the LCD panel during the LCD system adjustment.
6-51
HDR-FX1000/FX1000E_ADJ
2.
V-COM Adjustment (PD-372 board)
Set the DC bias of the common electrode drive signal of LCD to
the specified value.
If deviated, the LCD display will be move, producing flicker and
conspicuous vertical lines.
the specified value.
If deviated, the LCD display will be move, producing flicker and
conspicuous vertical lines.
Mode
VTR stop (VCR mode)
Signal
No signal
Measurement Point
Check on LCD screen
Measuring Instrument
Adjustment Page
C
Adjustment Address
A1
Specified Value
The brightness difference between
the section-A and section-B is
minimum
the section-A and section-B is
minimum
Note 1:
Perform “PANEL Gain Adjustment” before this adjust-
ment.
ment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Switch setting
VIDEO OUT .......................................................................... LCD
(Page: 7, address: 4F, Bit1 = 0)
VIDEO OUT .......................................................................... LCD
(Page: 7, address: 4F, Bit1 = 0)
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
7
01
95
4
7
04
00
5
7
00
01
Press PAUSE (Write) button.
6
C
A1
70
7
C
A1
Change the data so that
brightness of the section A
and section B is equal.
brightness of the section A
and section B is equal.
8
C
A1
Set a value obtained by
adding 3 to the
forementioned data, and
press PAUSE (Write) button.
adding 3 to the
forementioned data, and
press PAUSE (Write) button.
9
7
01
95
10
7
04
01
11
7
00
01
Press PAUSE (Write) button.
12
3
70
10
Press PAUSE (Write) button.
13
3
70
Check the data changes to
“11”.
“11”.
14
0
01
00
Fig. 6-1-13
3.
Transmissive Mode White Balance Adjustment
(PD-372 board)
(PD-372 board)
Correct the white balance at transmissive mode.
If deviated, the LCD screen color cannot be reproduced.
If deviated, the LCD screen color cannot be reproduced.
Mode
VTR stop (VCR mode)
Signal
No signal
Measurement Point
Check on LCD screen
Measuring Instrument
Adjustment Page
C
Adjustment Address
A2, A3
Specified Value
LCD screen must not be colored
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Check the white balance only when replacing the fol-
lowing parts. If necessary, adjust them.
1. LCD block
2. Light induction plate
3. IC6001
lowing parts. If necessary, adjust them.
1. LCD block
2. Light induction plate
3. IC6001
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
7
01
95
4
7
04
00
5
7
00
01
Press PAUSE (Write) button.
6
C
A2
20
Press PAUSE (Write) button.
7
C
A3
20
Press PAUSE (Write) button.
8
Check that the LCD screen is
not colored. If not colored,
proceed to step 10.
not colored. If not colored,
proceed to step 10.
9
C
A2
Change the data so that the
LCD screen is not colored.
(Note 3)
LCD screen is not colored.
(Note 3)
10
7
01
95
11
7
04
01
12
7
00
01
Press PAUSE (Write) button.
13
3
70
10
Press PAUSE (Write) button.
14
3
70
Check the data changes to “11”.
15
0
01
00
Note 3:
To write in the non-volatile memory (EEPROM), press
the PAUSE (Write) button each time to set the data.
the PAUSE (Write) button each time to set the data.
A3
A
A
A
A
B
B
B
B
Click on the first or last page to see other HDR-FX1000 / HDR-FX1000E (serv.man3) service manuals if exist.