DOWNLOAD Sony HDR-FX1000 / HDR-FX1000E (serv.man3) Service Manual ↓ Size: 1.02 MB | Pages: 81 in PDF or view online for FREE

6-52

HDR-FX1000/FX1000E_ADJ

Pin No.

Signal Name

Pin No.

Signal Name

1

XSYS_RST

11

EEP_SI_S

2

XCS_MC_FLASH

12

EEP_SI_C

3

XCS_MC_FLASH_C 13

GND

4

MD2

14

GND

5

MD2_C

15

REG_GND

6

D_2.8V

16

FRRV

7

EEP_SCK_S

17

SWP

8

EEP_SCK_C

18

REG_GND

9

EEP_SO_S

19

RF_MON

10

EEP_SO_C

20

REG_GND

1) Connect the adjustment remote commander to the LANC jack.

Set the HOLD switch to ON. (Set the slide switch to SER-
VICE).

2) Select page: 3, address: 26, set data: 00, and press the PAUSE

(Write) button.

3) Select page: 3, address: 33, and set data: 00.

CH1

Entrance side

Exit side

Check this section

(Normal waveform)

CH2

(Trigger)

3.3msec

The changed portions from
Ver. 1.0 are shown in blue.

For details of mechanism section adjustments, checks, and replace-
ment of mechanism parts, refer to the separate volume “DV ME-
CHANICAL ADJUSTMENT MANUAL IX  N Mechanism  ”.

Before performing the adjustments, check the data of page:
0, address: 10 is “00”. If not, set data: 00 to this address.

1) Connect the adjustment remote commander to the LANC jack.
2) Set the HOLD switch to ON. (Set the slide switch to SER-

VICE).

3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, set data: 0C, and press the PAUSE

(Write) button of the adjustment remote commander.
(The mechanism enters the record mode automatically.)

The function buttons become inoperable.

5) To quit the record mode, select page: 3, address: 01, set data:

00, and press the PAUSE (Write) button of the adjustment re-
mote commander.  (Whenever you want to quit the record
mode, be sure to quit following this procedure.)

1) Connect the adjustment remote commander 

(Ref. No. J-1, J-

2)

  to the LANC jack.

2) Set the HOLD switch to ON. (Set the slide switch to SER-

VICE).

3) Close the cassette compartment without the cassette.
4) Select page: 3, address: 01, set data: 0B, and press the PAUSE

(Write) button of the adjustment remote commander.
(The mechanism enters the playback mode automatically.)

The function buttons become inoperable.

5) To quit the playback mode, select page: 3, address: 01, set

data: 00, and press the PAUSE (Write) button of the adjust-
ment remote commander.  (Whenever you want to quit the play-
back mode, be sure to quit following this procedure.)

1) Clean the tape running side (tape guide, drum, capstan shaft,

pinch roller, etc.).

2) Connect the adjustment remote commander to the LANC jack.
3) Set the HOLD switch to ON. (Set the slide switch to SER-

VICE).

4) Connect an oscilloscope to VC-543 board CN1004 via the

CPC-13 Connecting jigs. (J-6082-443-A)

Channel 1: VC-543 board, CN1004 Pin ql (Note)
External trigger: VC-543 board, CN1004 Pin qj

Connect a 75 

Ω resistor between pins ql of CN1004

and w; (GND).
75 

Ω resistor (Parts code: 1-247-804-11)

5) Playback the alignment tape for tracking. (XH2-1) 

(Ref. No.

J-12)

6) Select page: 3, address: 33, and set data: 08.
7) Select page: 3, address: 26, set data: 31, and press the PAUSE

(Write) button.

8) Check that the oscilloscope RF waveform is normal at the en-

trance and exit.
If not normal, adjust according to the separate volume
“DV MECHANICAL ADJUSTMENT MANUAL IX
 N Mechanism ”.

6-53

HDR-FX1000/FX1000E_ADJ

Connect the measuring instruments as shown in Fig. 6-3-1, and
perform the adjustments.

Before performing the adjustment, check the data of page:
0, address: 10 is “00”. If not, select page: 0, address: 00,
and set data “00”.

1) The adjustments of this unit are performed in the VTR mode

(VCR mode) or camera mode (CAMERA mode).

The measuring point of the playback RF signal is CN1004 of VC-
543 board. Connect the measuring instruments via the CPC-13 jig
(J-6082-443-A). Refer to “MECHANISM SECTION ADJUST-
MENT” for the measuring method. The following table lists the
test pin numbers of CPC-13 jig, and the pin numbers and signal
names of CN1004.

Pin No.

Signal Name

Pin No.

Signal Name

1

XSYS_RST

11

EEP_SI_S

2

XCS_MC_FLASH

12

EEP_SI_C

3

XCS_MC_FLASH_C 13

GND

4

MD2

14

GND

5

MD2_C

15

REG_GND

6

D_2.8V

16

FRRV

7

EEP_SCK_S

17

SWP

8

EEP_SCK_C

18

REG_GND

9

EEP_SO_S

19

RF_MON

10

EEP_SO_C

20

REG_GND

A/V Connecting Cable (1.5 m)
(with S Video terminal)
(1-823-156-13)

HDMI OUT

 A/V R

LANC jack

Note: The pin arrangement is reverse between 

CN1004 of VC-543 board and CPC-13 jig. 
Accordingly, be careful when inserting the 
connector.

A/V R connector

Audio L (White)

S Video
(Black)

Video
(Yellow)

Audio R (Red)

VIDEO system adjustment (S VIDEO, VIDEO)

To
AC adaptor
(AC-L100)

1

20

Terminated
75 

Ω

20

1

CN1004

VC543 board

Adjustment remote commander

RM-95
(J-6082-053-B)

NEW LANC JIG
(J-6082-565-A)
LANC cable
(J-6082-442-A)

Oscilloscope

CPC-13 jig
(J-6082-443-A)

The changed portions from
Ver. 1.0 are shown in blue.

6-54

HDR-FX1000/FX1000E_ADJ

Use the alignment tapes shown in the following table.
Use tapes specified in the signal column of each adjustment.

Name

Use

Tracking tape (XH2-1)

Tape path adjustment

SW/OL standard (XH2-3)

Switching position adjust-
ment

Audio operation check

Audio system adjustment

(XH5-3 (NTSC), XH5-3P (PAL))

System operation check

Operation check

(XH5-5 (NTSC), XH5-5P (PAL))

Fig. 6-3-2 shows the 75% color bar signals recorded on the align-
ment tape for Audio Operation Check.

 Measure with video terminal (Terminated at 75 

Ω)

Color bar signal waveform

Color bar pattern

Color bar signal waveform

Color bar pattern

10-pin connector
Video signal: 1 Vp-p, 75 

Ω (ohms)

Luminance signal: 1 Vp-p, 75 

Ω (ohms)

Chrominance signal: 0.286 Vp-p (burst signal), 75 

Ω (ohms)

(NTSC)
Chrominance signal: 0.3 Vp-p (burst signal), 75 

Ω (ohms)

(PAL)
Audio signal: -10 dBu (at load impedance 47 k

Ω (kilohms)),

Output impedance with less than 2.2 k

Ω (kilohms)

(0 dBu=0.775 Vrms)

Y: 1 Vp-p, 75 

Ω (ohms), P

B

/P

R

, C

B

/C

R

: +/- 350 mV, 75 

Ω

(ohms)

1 V

0.714 V

0.286 V

White (75%)

White (100%)

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Burst signal

0.286 V

Q

I

Horizontal sync signal

(75%)

White

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Q

I

White

(100%)

Black

1 V

0.7 V

0.3 V

White (100%)

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Burst signal

Horizontal sync signal

0.3 V

(100%)

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

White

Blac

k

6-55

HDR-FX1000/FX1000E_ADJ

D

1

 (decimal)

D

2

 (decimal)

H

1

 (hexadecimal)

(Service model code)

00001 to 65535

D

1

FE

65536 to 131071

D

1

 

− 65536

FE

131072 to196607

D

1

 

− 131072

FE

196608 to 262143

D

1

 

− 196608

FE

262144 to 327679

D

1

 

− 262144

FE

327680 to 393215

D

1

 

− 327680

FE

393216 to 458751

D

1

 

− 393216

FE

458752 to 524287

D

1

 

− 458752

FE

524288 to 589823

D

1

 

− 524288

FE

589824 to 655359

D

1

 

− 589824

FE

655360 to 720895

D

1

 

− 655360

FE

720896 to 786431

D

1

 

− 720896

FE

786432 to 851967

D

1

 

− 786432

FE

851968 to 917503

D

1

 

− 851968

FE

917504 to 983039

D

1

 

− 917504

FE

983040 to 999999

D

1

 

− 983040

FE

5) Enter H

1

 to address: 09 on page: 13.

Example: If H

1

 = FE,

Select page: 0, address: 10, and set data: 01.
Select page: 3 (13), address: 09, and set data: FE, then press
the PAUSE (Write) button.

6) From Table 6-3-3, obtain the maximum decimal number less

than D

2

, and it is assumed to be D

3

.

Example: If D

2

 = 12345.

D

3

 = 12288

7) From Table 6-3-3, obtain a hexadecimal number that corre-

sponds to D

3

, and it is assumed to be H

3

.

Example: If D

3

 = 12288,

H

3

 = 3000

8) Caluculate D

4

  using following equa tions (decimal

caluculation). (0   D

4

 

 225)

D

4

 = D

2

 – D

3

Example: If D

2

 = 12345 and D

3

 = 12288,

D

4

 = 12345 – 12288 = 57

9) Convert D

4

 into a hexadecimal number to obtain H

4

. (See Table

6-4-1 “Hexadecimal - decimal conversion table” in 6-4. Ser-
vice Mode)
Example: If D

4

 = 57,

H

4

 = 39

10) Enter higher two digits of H

3

 to address: 0A on page: 13.

Example: If H

3

 = 3000,

Select page: 0, address: 10, and set data: 01.
Select page: 3 (13), address: 0A, and set data: 30, then press
the PAUSE (Write) button.

11) Enter H

4

 to address: 0B on page: 13.

Example: If H

4

 = 39,

Select page: 0, address: 10, and set data: 01.
Select page: 3 (13), address: 0B, and set data: 39, then press
the PAUSE (Write) button.

12) Select page: 0, address: 10, and set data: 00.
13) Select page: 3, address: 70, and set data: 10, then press the

PAUSE (Write) button.

14) Select page: 3, address: 70, and check that the data changes to

“11”.

15) Select page: 0, address: 01, and set data: 00.

If the EEPROM data is erased due to some reason, perform “1-2.
INITIALIZATION OF EVR DATA ”, of “6-1. CAMERA SEC-
TION ADJUSTMENTS”

Perform “2-2. Input of Serial No.” if the data on page 13
has been cleared and original node unique ID No. is un-
certain.
Usually, read the data on page 13 before repair, and write
it after repair.

If reading/writing data on pages 13, set data: 01 to page:
0, address: 10, and then select pages: 3. By this data set-
ting, the pages 13 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Write the company ID to the EEPROM (nonvolatile memory).

Page

13

Address

04, 05, 06, 07

Input method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 71, and set data: 01, then press the

PAUSE (Write) button.

3) Select page: 0, address: 10, and set data: 01.
4) Select page: 3 (13), and enter the following data.

Each time the data is set, press the PAUSE (Write) but-
ton on the adjusting remote commander.

Address

Data

04

08

05

00

06

46

07

01

 5)Select page: 0, address: 10, and set data: 00.

6) Select page: 3, address: 70, and set data: 10, then press the

PAUSE (Write) button.

7) Select page: 3, address: 70, and check that the data changes to

“11”.

8) Select page: 0, address: 01, and set data: 00.

Write the serial No. and model code to the EEPROM (nonvolatile
memory).
In writing the serial No., a decimal number should be converted
into a hexadecimal number

Page

13

Address

08, 09, 0A, 0B

1) Select page: 0, address: 01, and set data: 01.
2) Select page: 3, address: 71, and set data: 01, then press the

PAUSE (Write) button.

3) Read the serial No. from the model name label, and it is as-

sumed to be D

1

.

Example: If serial No. is “77881”,

D

1

 = 77881

4) From Table 6-3-2, obtain D

2

 and H

1

 that correspond to D

1

.

Example: If D

1

 = 77881,

D

2

 = D

1

 – 65536 = 12345

H

1

 = FE