Sharp XG-V10XE (serv.man32) User Manual / Operation Manual ▷ View online
52
“Fine Sync” Adjustment
“Fine Sync”
adjustment is not necessary except “Auto Sync Setup”
and “Special Modes” with Input3 (DVI) mode (The “Input Adjust” and
“Settings”
“Settings”
items cannot be adjusted.).
1
to
4
: Slide the bar to the desired location or simply type in the desired
value in the box.
1
To make “Clock” adjustment
2
To make “Phase” adjustment
3
To make “H-POS” adjustment
4
To make “V-POS” adjustment
5
To reset all the adjustments
1
to
4
Press the “Reset” button.
6
Select the “Auto Sync Setup” ON/OFF.
“ON”
is for “Auto Sync” whenever the projector is powered or
the input signal is changed.
7
To select the “Special Modes”
8
To make “Auto Sync Display” ON/OFF.
“ON” is for displaying Background Image during “Auto Sync”.
9
To store up to seven adjustment settings for use with various
computers
Connect a PC to the projector and make the adjustments in “Input
Adjust”
Adjust”
. And then press one of the “Save No.” buttons to save
the adjustment setting.
●
Make a note of the “Save No.” and its stored setting, if necessary.
You cannot check each setting with this software after saving it.
You cannot check each setting with this software after saving it.
●
The previous setting will be overwritten if you save on the same
“Save No.”
“Save No.”
button.
0
To select the desired adjustment setting for the currently connected
PC, press the desired “Select No.” button.
Refer to
e
,
r
,
t
on
page 51
about the function of
q
,
w
,
e
on this
page.
1
2
3
4
5
2
3
4
5
q
w
9
0
e
6
7
8
53
Adjusting and
Controlling
“Audio” Adjustment
1
,
2
,
3
and
5
: Slide the bar to the desired location or simply type in
the desired value in the box.
1
To make “Balance” adjustment
2
To make “Treble” adjustment
3
To make “Bass” adjustment
4
To reset the adjustments
1
,
2
and
3
Press the “Reset” button.
5
To make “Volume” adjustment
6
Select the “Mute” ON/OFF.
7
To send all the adjustment data to the projector
Press the “Send” button to control all the adjustments on this
sheet.
sheet.
8
To receive data from the projector
Press the “Receive” button to confirm the adjustments on the
projector.
projector.
9
A “Now Transmitting...” message
is displayed during
transmission.
7
8
5
6
9
1
2
3
4
2
3
4
54
“Options” Adjustment
1
to
2
and
q
: Select ON/OFF.
4
to
0
: Select a mode from the pull down menu.
1
To make “3D DNR” ON/OFF
2
To make “Auto Power Off” (Automatic Power Shutoff) ON/OFF
The Automatic Power Shutoff function will not operate when
performing Advanced Control for Adjustment, although you set it
“ON”.This function operates during Presentation Transfer, Capture
& Transfer
performing Advanced Control for Adjustment, although you set it
“ON”.This function operates during Presentation Transfer, Capture
& Transfer
, or Gamma Correction.
3
See the next page
4
To make “OSD Display” select
5
To make “Video System” select
6
To make “Background Image” select
7
To make “Startup Image” select
8
To make “ID No. Display” select
9
To make “Lamp Mode” select
0
To make “PRJ Mode” select
q
To make “Set Inputs” ON/OFF from Input1 to 6
w
To send all the adjustment data to the projector
Press the “Send” button to control all the adjustments on this
sheet.
sheet.
e
To receive data from the projector
Press the “Receive” button to confirm the adjustments on the
projector.
projector.
r
A “Now Transmitting...” message
is displayed during transmission.
1
2
567
8
w
e
4
9
0
q
3
r
55
Adjusting and
Controlling
3
Press the “Get Information” (Lamp & Signal information) button
to open the “Information” window.
“Model”
Shows the model number of the projector.
“Power Status”
On:
The power is on.
Off:
The power is off.
Cooling: The power is off with the cooling fan turning. Do not
disconnect the power cord during “Cooling”.
“Lamp Status”
On:
The lamp is on.
Off:
The lamp is off.
Retry:
Retrying to turn on the lamp.
Wait:
The lamp is on standby.
“Lamp Timer”
Shows the accumulated lamp usage time. It will be reset when
replacing the lamp.
replacing the lamp.
“Trouble Status”
Temp.: The internal temperature is abnormally high. Something
may block air intake.
Fan:
The filter cover is open. Securely install the filter cover.
Lamp:
The lamp has a problem.
Normal: Displayed in the normal operating condition.
“Real Resolution”
Shows the resolution of the projector’s panel.
“Input Status”
Input1/Input2/Input3/Input4/Input5/Input6
“Resolution”
(Displayed for Input1/2/3)
Shows the resolution of the image when projected on the screen.
“Hor Freq”
(Displayed for Input1/2/3)
Shows the horizontal frequency (kHz).
“Vert Freq”
(Displayed for Input1/2/3)
Shows the vertical frequency (Hz).
“Video System”
(Displayed for Input 4/5)
Shows the video input system (NTSC or PAL etc.). The “---” will be
displayed when it is a monochrome or there is no signal. For a
forced system, a “*” will lead the system name.
displayed when it is a monochrome or there is no signal. For a
forced system, a “*” will lead the system name.
Click on the first or last page to see other XG-V10XE (serv.man32) service manuals if exist.