Sharp MX-PEX1 (serv.man3) Service Manual ▷ View online
37
Restoring functionality after service
4.
Mount the Fiery X3eTY2 on the back of the MFP.
Align the slotted holes on the Fiery X3eTY2 with the upper mounting screws attached to
the MFP (see Figure S). Carefully lower the Fiery X3eTY2 until the narrow ends of the
slotted holes engage the four mounting screws.
the MFP (see Figure S). Carefully lower the Fiery X3eTY2 until the narrow ends of the
slotted holes engage the four mounting screws.
F
IGURE
S
Mounting the Fiery X3eTY2 on the MFP
5.
Replace the two lower mounting screws that secure the bottom edge of the Fiery X3eTY2
to the MFP.
to the MFP.
6.
Tighten all four mounting screws.
Make sure that the screws are fully tightened and that the Fiery X3eTY2 is firmly
attached to the MFP.
attached to the MFP.
Upper mounting screw
(1 of 2)
(1 of 2)
Lower mounting screw
(1 of 2)
(1 of 2)
Slotted hole (1 of 2)
38
Restoring functionality after service
7.
Connect any external cables that you removed during inspection or service
(see Figure T).
(see Figure T).
Make sure that the following cables are properly connected:
• Network cable
• MFP interface cable
• MFP Ethernet cable
F
IGURE
T
External Fiery X3eTY2 connections
MFP interface connector
MFP Ethernet connector (10/100 BaseT)
Network connector (10/100/1000 BaseT)
Monitor port (not used)
Serial port (not used)
USB-Type A ports
USB-Type B port (not used)
39
Restoring functionality after service
8.
If you installed a new HDD, install system software (see page 44).
A spare HDD is shipped without system software.
9.
Make sure both service switches are in normal position (away from the motherboard).
10.
Power on the MFP using the main power switch in the front compartment, and then the
secondary power switch on the Control Panel. Then move the power switch on the
Fiery X3eTY2 to the ON (|) position.
secondary power switch on the Control Panel. Then move the power switch on the
Fiery X3eTY2 to the ON (|) position.
Allow the MFP to start up and display ready status on the Control Panel.
11.
Before you leave the customer site, verify Fiery X3eTY2 operation as described in the
following flow diagram:
following flow diagram:
F
IGURE
U
Steps to verify the Fiery X3eTY2
Power up and print test pages
(see page 40).
(see page 40).
Check the Setup options (see
Configuration and Setup on the User
Documentation CD).
Configuration and Setup on the User
Documentation CD).
Connect the Fiery X3eTY2 to the
network and verify (see page 42).
network and verify (see page 42).
40
Restoring functionality after service
Printing Fiery X3eTY2 pages
The MFP touch panel allows you to print special pages that reside on the Fiery X3eTY2
HDD. These pages include the following:
HDD. These pages include the following:
•
Test Page:
Verifies that the Fiery X3eTY2 is functional and connected properly to the
MFP. Before connecting the Fiery X3eTY2 to the network, print the Test Page.
•
Configuration page:
Lists all the settings in effect from the current Setup. After you
have finished running Setup, print a Configuration page to confirm your settings. If
the Fiery X3eTY2 is rebooting, allow the Fiery X3eTY2 to reboot and return to Idle
before printing a Configuration page.
the Fiery X3eTY2 is rebooting, allow the Fiery X3eTY2 to reboot and return to Idle
before printing a Configuration page.
Before you perform any service procedure, print the Configuration page (if possible) so
that you can return the settings to their former configurations, if necessary.
that you can return the settings to their former configurations, if necessary.
After the connection to the network is made, the network administrator can customize
Setup options according to the network and user environment. Using the
Configuration page as a guide can help speed up this process.
Setup options according to the network and user environment. Using the
Configuration page as a guide can help speed up this process.
If desired, you can also print additional Fiery X3eTY2 pages.
T
O
PRINT
F
IERY
X3
E
TY2
PAGES
1.
Press the System Settings button on the MFP.
2.
On the MFP touch panel, press Admin Password. Then press Password.
3.
On the touch panel, use the keyboard to enter the administrator password for the MFP.
Press OK, and press OK again at the next screen.
Press OK, and press OK again at the next screen.
N
OTE
:
This password is not the same as the administrator password for the
Fiery X3eTY2.
4.
At the System Settings screen, use the arrows to scroll to Printer Settings.
Press Printer Settings.
Press Printer Settings.
Click on the first or last page to see other MX-PEX1 (serv.man3) service manuals if exist.